XTOOL XTS500 Wireless Diagnostics Module User Manual

Connect OBDII-16 port of VCI Box to the vehicle’s DLC port.
Plug the USB wireless receiver into the USB port of the PC.
Go to the Wi-Fi selection page of your PC. Select WLAN 2 and search for the Wi-Fi hotspot with the same name as the SN of the device.
Once connected, your PC has established a connection with the device.

Connexion filaire

Connect OBDII-16 port of VCI Box to the vehicle’s DLC port.
Connect the VCI and the diagnostic PC with a USB Type-C cable.

Précautions pour le diagnostic

Ensure proper connections are made and follow safety protocols while performing diagnostics on vehicles.

About J2534 Toolbox
To install J2534 Toolbox:

Scannez le code QR ou visitez
https://www.xtooltech.com/english/DownloadCenter.html to find the installation pack.
Décompressez le fichier téléchargé file and run Setup.exe. Follow the installation process.
After installation, restart your PC for changes to take effect.

Comment utiliser
To use J2534 Toolbox:

For wired connection: Directly connect the VCI to the diagnostic PC via USB cable. The Toolbox will detect the device automatically.
If not detected, click the Refresh button to try again.
For wireless connection: Plug in the WiFi Receiver, click the WiFi button, select WLAN 2, find the matching hotspot, and connect.
Ensure a stable connection before proceeding with diagnostics.

Marques déposées
XTOOL is a trademark of Shenzhen Xtooltech Intelligent Co., Ltd. Copyright, registered in China, the United States, and other countries. All other marks are trademarks or registered trademarks of their respective holders.

Clause de non-responsabilité et limitation de responsabilité
All information, specifications and illustrations in this manual are based on the latest information available at the time of printing. Xtool reserves the right to make changes at any time without notice. While information of this manual has been carefully checked for accuracy, no guarantee is given for the completeness and correctness of the contents, including but not limited to the product specifications, functions, and illustrations. Xtool will not be liable for any direct, special, incidental, or indirect damages, or for any economic consequential damages (including the loss of profits) as a result of using this product.

Before operating or maintaining this unit, please read this manual carefully, please pay extra attention to the safety warnings and precautions.

Assistance et service

Officiel Website: www.xtooltech.com
E-mail: xtoolinplusus@outlook.com

Présentation générale

Perspectives et ports

OBDII-16 port: Connect to vehicle’s DLC port.
Nameplate: Show device information.
Type-C Port: Connect the device to diagnosis PC via wire.
Indicator Light: Show device status.

Couleur du voyant lumineux	Voyant Signification
Feu vert continu	Sous tension
Lumière verte clignotante	Mise à jour du firmware
Lumière bleue continue	Device connected (no communication)
Lumière bleue clignotante	Communicating with the vehicle
Lumière rouge clignotante	Défaut de l'appareil

Commencer

Connexion du véhicule

Connexion sans fil

Connect OBDII-16 port of VCI Box to vehicle’s DLC port.
Plug the USB wireless receiver into the USB port of the PC.
Go to Wi-Fi selection page of your PC. Select “WLAN 2”, and search for the Wi-Fi hotspot that has the same name as the SN of the device.
Once the hotspot is connected, your PC has established connection with the device.

Connexion filaire

Connect OBDII-16 port of VCI Box to vehicle’s DLC port.
Connect the VCI and the diagnostic PC with a USB Type-C cable.

Précautions pour le diagnostic

Le voltagPortée sur la voiture : +9~+36V DC ;
When testing some special functions, the operator must operate according to the prompts and meet the test conditions. In some cases, the conditions that need to be met are: engine water temperature 80 ℃~105 ℃, turn off headlights and air conditioners, keep the accelerator pedal in the released position, etc.;
Les systèmes de contrôle électronique des différents modèles sont très compliqués. Si vous rencontrez des situations où il est impossible de tester ou si une grande quantité de données de test est anormale, vous pouvez rechercher l'ECU du véhicule et sélectionner le menu du modèle sur la plaque signalétique de l'ECU ;
Seuls les faisceaux de câbles fournis par XTOOL et conçus pour l'appareil peuvent être utilisés avec cet appareil afin d'éviter d'endommager le véhicule ou l'appareil ;
When running a diagnostics session, DO NOT shut down the device directly. You should cancel the task before returning to the main interface and then shutting down the device.

About J2534 Toolbox
J2534 Toolbox is a PC application that manage the updates and operation logs for all VCIs that supports J2534 function. Before you start working on diagnostics with your PC, make sure you have the J2534 Toolbox installed.

Installation

Scan the QR code on the right, or go to:https://www.xtooltech.com/english/DownloadCenter.html
And find “J2534 Toolbox” for the installation pack.
After the download is completed, unzip it and click “Setup.exe”, then follow the installation process. We suggest you to restart your PC after installation.

Comment utiliser

The picture on the right shows the main screen of the J2534 Toolbox when the VCI is not connected to the diagnostic PC.

Device Connection – Wired

Directly connect the VCI to the diagnostic PC via USB cable. The Toolbox will automatically detect the device when you connect it.
If the status has not been refreshed after you connect the VCI via wire, click the Refresh button to try again.

Device Connection – Wireless

Plug in the WiFi Receiver that comes with the VCI box.
Click the WiFi button on the bottom-left corner and select “WLAN 2” (or other numbers)
Find the hotspot that names the same as the SN of the VCI box and click “Connect”.
When the connection is ready, you are OK to go.

Écran principal
When the VCI is connected, you will see this screen:

SN: Shows the SN of the current VCI.
Firmware Version: Shows current firmware version that is installed on the VCI.
Driver Version: Shows current driver version that is installed on the VCI.
J2534 Authorization: Shows the VCI authorization status of current VCI.

Log Record: Turn on/off the J2534 communication logs recording.
Feedback: Send feedback to XTool customer service team when you meet any issues regarding the J2534 connection.

Firmware/Driver Update

If there is an update for the firmware or the driver, you will see a red dot beside the version number. Click the Update button on the right to check updates.
You can choose the version first, and click “Upgrade” button on the right to start updates.
DO NOT DISCONNECT THE VCI WHEN THE UPDATE IS IN PROGRESS!

Paramètres

Click the “Settings” button on the top-right corner and go to the Toolbox settings.
Languages: Click to change language shown on the Toolbox.
Version Number: Check the updates of the Toolbox.
Log Cache: Show the size of the log folder. You can click the button on the right to clear all logs.
Save Location: This shows the location of the log folder. You can click this to get into the folder.

DoIP Mode Switch: When there are cases that the vehicle asks for a DoIP connection, please turn on the switch to enable DoIP mode. Please note that the DoIP mode can only be enabled in wired connection.

Retour

If you meet any issues regarding J2534 connection, please record the logs (turn on the log recording switch) and send the logs to XTool customer service team. To better locate your problems, we need the following information in the report:

Votre adresse e-mail
Enregistrer files, recorded when the issues happened
Vehicle information (brand, model, MY)
Firmware/Driver version info
A brief description on what is going on (you can also attach images & screenshots)

Our customer service team will handle this and reply to you via email.

Conformité FCC

FCC ID: 2AW3IV01W2

Cet appareil est conforme à la partie 15 des règles de la FCC. Son fonctionnement est soumis aux deux conditions suivantes :

Cet appareil ne doit pas provoquer d'interférences nuisibles
Cet appareil doit accepter toute interférence reçue, y compris celles qui peuvent provoquer un fonctionnement indésirable.

Avertissement
Les changements ou modifications non expressément approuvés par la partie responsable de la conformité pourraient annuler l'autorité de l'utilisateur à utiliser l'équipement.

Note
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment can generate, use and radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Réorienter ou déplacer l’antenne de réception.
Augmenter la séparation entre l’équipement et le récepteur.
Connectez l’équipement à une prise sur un circuit différent de celui auquel le récepteur est connecté.
Consultez le revendeur ou un technicien radio/TV expérimenté pour obtenir de l’aide.

Partie responsable

Nom de l'entreprise : FCC US Agent, LLC
Adresse : 3722 Illinois Avenue, Saint Charles, IL, 60174, États-Unis
E-mail: Support@FCCUSAgent.com

Déclaration de l'ISDE

IC: 29441-V01W2
Modèle : XTS500
PMN: V120，XTS500
HVIN: V01W2A

Cet appareil contient des émetteurs/récepteurs exempts de licence qui sont conformes aux normes CNR exemptes de licence d'Innovation, Sciences et Développement économique Canada. Son fonctionnement est assujetti aux deux conditions suivantes :

Cet appareil ne doit pas provoquer d'interférences.
Cet appareil doit accepter toute interférence, y compris celles qui peuvent provoquer un fonctionnement indésirable de l'appareil.

Déclaration de conformité
Par la présente, Shenzhen XTOOLtech Intelligent Co., Ltd déclare que ce module de diagnostic sans fil est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 2014/53/UE. Conformément aux articles 10(2) et 10(10), ce produit est autorisé à être utilisé dans tous les États membres de l'UE.

Royaume-UniCA

Par la présente, Shenzhen XTOOLtech Intelligent Co., Ltd déclare que ce module de diagnostic sans fil satisfait à toutes les réglementations techniques applicables au produit dans le cadre des réglementations britanniques sur les équipements radio (SI 2017/1206) ; des réglementations britanniques sur les équipements électriques (sécurité) (SI 2016/1101) ; et des réglementations britanniques sur la compatibilité électromagnétique (SI 2016/1091) et déclare que la même demande n'a pas été déposée auprès d'un autre organisme agréé au Royaume-Uni.
Shenzhen Xtooltech Intelligent Co., Ltd.
Ajouter : 17&18/F, bâtiment A2, ville créative, avenue Liuxian, district de Nanshan, Shenzhen, Chine
Siège social de Shenzhen Tél. : +86 755 2399608
E-mail: marketing@xtooltech.com

FAQ

What operating system does XTS500 J2534 support?

The device only support Windows 7/8/10/11 or later version.

Why can’t my Mac recognize this device?

The device does not support macOS system.

Does the device need to be activated for usage?

This device need no S/N or activation code to activate the device. It will work directly with OE software once connection.

What functions can this device achieve?

This device can do what OE dignostic software do. Please check the compatibility before usage.

Dose the device include OE software?

OE software is not included in the package. You need to subscribe the OE software from manufacturer.

Documents / Ressources

XTOOL XTS500 Wireless Diagnostics Module [pdf] Manuel de l'utilisateur
XTS500 Wireless Diagnostics Module, XTS500, Wireless Diagnostics Module, Diagnostics Module, Module

Références

Manuel d'utilisation

XTOOL XTS500 Wireless Diagnostics Module

Caractéristiques

Instructions d'utilisation du produit