Home › ATOMSTACK › ATOMSTACK L2 Smart Z-Axis Module Installation Guide

Guide d'installation du module intelligent de l'axe Z ATOMSTACK L2

ATOMSTACK-L2-Smart-Z-Axis-Module-featured-image

Module intelligent d'axe Z ATOMSTACK L2

Manuel d'installation du réglage automatique de la hauteur de l'axe Z L2-5W/L2-10W/L2-20W/L2-40W

Note: Les images sont à titre de référence uniquement, veuillez vous référer au produit réel. Pour plus d'informations, veuillez scanner le code QR.

liste

Méthode d'installation de l'axe Z

A5 PRO V2/A10 PRO V2

Dévissez 4 pièces M4*6 dans le sens inverse des aiguilles d'une montre pour retirer le curseur

Installer le connecteur dédié A5 Pro V2/A10 Pro V2
Serrez 4 pièces M4*6

A20 PRO V2/A40 PRO V2

A6 Pro / A12 Pro / A24 Pro / X12 Pro / X24 Pro / E6 Pro / E18 Pro / E24 Pro / A6 Ultral / A12 Ultral / A24 Ultral / X12 Ultral / X24 Ultral A48 PRO/A48 Ultra pas besoin de déplacer les fins de course

Étape 1

Retournez le graveur
Retirez les 2 vis de la carte de fin de course
Avancer la planche pour aligner les 2 trous
Verrouillez 2 vis sur la carte
Finition
Retournez le graveur

Méthode d'installation unifiée au laser

Étape : 1 Retirez 4 pièces M3 et le curseur laser
Étape : 2 Installez le curseur laser avec les 4 vis M3 retirées de l'étape 1

Remarque : Dévissez La pièce de fixation avec le tournevis cruciforme dans la boîte à outils, puis installez le curseur laser sur le laser A48.

Méthode de connexion par câble

Méthode d'installation du laser
A5 PRO V2/A10 PRO V2/A20 PRO V2/A40 PRO V2

A6 Pro / A12 Pro / A24 Pro / X12 Pro / X24 Pro / E6 Pro / E18 Pro / E24 Pro / A6 Ultra/ A12 Ultra/A24 Ultra/X12 Ultra/ X24 Ultra

A5 PRO V2/A10 PRO V2/A20 PRO V2/A40 PRO V2

Note: Lors de la mise sous tension pour utiliser le réglage automatique de la hauteur de l'axe Z, il vous suffit d'appuyer sur le bouton « mise au point automatique » du boîtier de commande pour mettre au point automatiquement le laser.

A6 Pro / A12 Pro / A24 Pro / X12 Pro / X24 Pro / E6 Pro / E18 Pro / E24 Pro / A6 Ultra / A12 Ultra / A24 Ultra / X12 Ultra / X24 Ultra

Note: L'affichage est nécessaire lorsque vous utilisez le réglage automatique de la hauteur de l'axe Z, vous devez le contrôler depuis l'extrémité de l'affichage.

Service client: Pour une politique de garantie détaillée, veuillez visiter notre site officiel website : www.atomstack.com Pour l'assistance technique et le service, veuillez envoyer un e-mail à : support@atomstack.com
Fabricant: Shenzhen AtomStack Technologies Co., Ltd
Adresse: 17e étage, bâtiment 3A, phase II, parc intelligent, n° 76, avenue Baohe, code Bip : tret, district de Longgang, Shenzhen, Guangdong, Chine
Scanner le code QR : OU lecteur de code/scanner de codes-barres ou toute application avec un scanner

Documents / Ressources

Module intelligent de l'axe Z L2

Installation Guide · L2, L2 Smart Z-Axis Module, Smart Z-Axis Module, Z-Axis Module, Module

Références

Manuel d'utilisationmanual.tools

Published: July 13, 2024

Mise à jour : 14 juillet 2024

Questions et réponses

Helpful product questions tied to this manual. Each item links to the full Q&A page.

Questions et réponses

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

🇺🇸 Robert dit:

23 avril 2026 à 12h48
I have an ATOMSTACK A20 PRO V2 machine and have just purchased a L2 Z axis motorized drive ( BM AAS41A0125-AB ) and would like to hook it up but the cable attached to the unit has a connector which does not match any place on my machine . Where does it go to . In the instructions it looks like where the connection for the y motor is. Please clarify how to hook it up . Thank You Bob
🇺🇸 Robert asks I have an ATOMSTACK A20 PRO V2 machine and have just purchased a L2 Z axis motorized drive ( BM AAS41A0125-AB ) and would like to hook it up but the cable attached to the unit has a connector which does not match any place on my machine . Where does it go to . In the instructions it looks like where the connection for the y motor is. Please clarify how to hook it up . Thank You Bob

Manuals+ clarified question

Question

How do I connect the L2 Smart Z-Axis Module cable to an ATOMSTACK A20 PRO V2 machine?
Répondre

Pour connecter le Module intelligent d'axe Z ATOMSTACK L2 à votre A20 PRO V2, you must use the specific wiring method outlined in the manual for "V2" series machines. The connection does not plug directly into a spare port on the motherboard; instead, it typically involves an adapter or a specific bridge connection.

Selon le Section 05 — Cable connection method for the A20 PRO V2:

X-Axis Connection: The Z-axis module cable usually connects to the transfer board located on the X-axis carriage.

Y-Axis Motor Comparison: While the connector may look similar to a Y-axis motor plug, it is intended for the Z-axis control port. On V2 models, this is often a 4-pin or 6-pin connector located on the breakout board near the laser module mount.

Check for the Adapter: Ensure you are using the "Z-axis connection cable" included in the L2 kit (listed as item 4 in the 01-List). One end connects to the L2 module motor, and the other connects to the reserved Z-axis port on the machine's X-axis terminal.

If the connector physically does not fit any port on the X-axis carriage board, please verify if your kit included a small carte adaptateur ou un Y-shaped splitter cable, as some V2 revisions require splitting the signal or using a specific conversion interface provided in the L2 box.
Read the full Q&A page
Répondre
1. 🇺🇸 Robert dit:
  
  23 avril 2026 à 2h31
  I don’t know what the transfer board is nor do I see anything on the x axis carriage. What is the x axis terminal ? I don’t see any extra ports anywhere .
  🇺🇸 Robert asks I don't know what the transfer board is nor do I see anything on the x axis carriage. What is the x axis terminal ? I don't see any extra ports anywhere .
  
  Manuals+ clarified question
  
  Question
  
  Where are the transfer board and X-axis terminal located on the ATOMSTACK L2 Smart Z-Axis Module?
  
  Répondre
  
  Based on the installation manual for the Module intelligent d'axe Z ATOMSTACK L2, the components you are looking for are part of the cable connection setup (Section 05):
  
  Transfer Board: This is the small PCB (circuit board) located on the back or side of the X-axis carriage (the part that moves left and right). On many AtomStack models like the A6, A12, A24, and X24 series, this board is where the main ribbon cable connects.
  
  X-axis Terminal: This refers to the specific port on that transfer board. For the L2 module, you typically need to plug the Z-axis connection cable into the port labeled for the Z-axis or the auxiliary port on this board.
  
  Note: If you do not see extra ports, ensure you are looking at the dos of the laser carriage assembly. On some older models (like the A5 Pro or V2 series), the connection method differs and may involve connecting directly to the main control box or using a specific adapter cable included in the L2 kit. Please verify your specific machine model, as the manual shows different wiring paths for the A5/V2 series par rapport au Pro/Ultra series.
  
  Read the full Q&A page
  Répondre
  1. 🇺🇸 Robert dit:
    
    23 avril 2026 à 2h55
    I do not see any PCB or any extra ports. Nor is there any adapters or splitters in the box.
    
    🇺🇸 Robert asks I do not see any PCB or any extra ports. Nor is there any adapters or splitters in the box.
    
    Manuals+ clarified question
    
    Question
    
    Where are the PCB, extra ports, adapters, or splitters for the ATOMSTACK L2 Smart Z-Axis Module?
    
    Répondre
    
    Based on the ATOMSTACK L2 Smart Z-Axis Module installation guide, the components included in the box (Section 01 - List) are:
    
    Z-axis height adjuster
    
    Laser slider
    
    A5/P/A10/A20/X20/S20 dedicated connector
    
    Vis M3 * 6
    
    Vis M4 * 5
    
    Z-axis connection cable
    
    Manuel
    
    Clé Allen 2.0/2.5
    
    Tournevis cruciforme
    
    Regarding the PCB and Ports: The L2 module is designed to integrate with existing AtomStack frames. For many models (like the A6 Pro, A12 Pro, A24 Pro, etc.), the connection is made directly to the existing X-axis motor interface or the laser module's connection point using the provided Z-axis connection cable. There is typically no separate external PCB board included in this kit.
    
    Regarding Adapters/Splitters: The manual shows that for certain models (Section 05 - Cable connection method), you must unplug the original X-axis motor cable and connect it to the Z-axis module's interface, or use the dedicated connector provided in the kit. If your specific machine model is not listed in the manual (A5, A10, A20, A6 Pro, etc.), you may require a specific adapter not included in the standard L2 package. If these items are missing from your specific kit, it is recommended to contact support@atomstack.com pour vérification.
    
    Read the full Q&A page
    Répondre
    1. 🇺🇸 Robert dit:
      
      23 avril 2026 à 3h23
      
      Now what do I do ?
      
      🇺🇸 Robert asks Now what do I do ?
      
      Manuals+ clarified question
      
      Question
      
      What are the next steps after installing the ATOMSTACK L2 Smart Z-Axis Module?
      
      Répondre
      
      Once you have physically mounted the ATOMSTACK L2 Smart Z-Axis Module and connected the cables as shown in the manual, you must configure your software to recognize the new hardware. Follow these steps:
      
      Vérification du câble : Ensure the Z-axis connection cable is securely plugged into the module and the corresponding port on your laser engraver's motherboard (refer to Section 05 of the manual for your specific model).
      
      Configuration du logiciel: Open your laser control software (LightBurn or LaserGRBL). You may need to enable the Z-axis in the device settings. In LightBurn, go to Paramètres de l'appareil and ensure 'Enable Z-Axis' is toggled on.
      
      Mise au point : The L2 module is designed for automatic or simplified focusing. Use the control panel or software commands to move the Z-axis up and down to verify smooth movement before starting a project.
      
      Interrupteurs de fin de course : If you are using models like the A6 Pro, A12 Pro, or A24 Pro, the manual notes that you do not need to relocate the limit switches.
      
      If the module is not moving, double-check that the 2-pin or 4-pin connectors are not reversed and that your machine's firmware is up to date.
      
      >
      
      Read the full Q&A page
      
      Répondre

Poser une question Cancel question

Sujets connexes

Module L2

Module intelligent d'axe Z ATOMSTACK L2

Méthode d'installation de l'axe Z

Méthode d'installation unifiée au laser

Méthode de connexion par câble

Documents / Ressources

Références

Questions et réponses

Answered questions

Questions et réponses

Poser une question Cancel question

Sujets connexes

Dernier EMPILEMENT ATOMIQUE Manuels