Introduction
Thank you for choosing the DD Audio SS6000 Monoblock Amplifier. Cette amplifier is designed to deliver high-performance audio for your vehicle's sound system. This manual provides essential information for the correct installation, operation, and maintenance of your SS6000 ampAmplificateur. Veuillez lire attentivement ce manuel avant toute installation ou utilisation afin de garantir des performances et une sécurité optimales.
Consignes de sécurité
Observe the following safety precautions to prevent injury and damage to the ampamplificateur ou véhicule :
- Débranchez toujours la borne négative de la batterie du véhicule avant d'entreprendre tout travail électrique.
- Assurer une bonne mise à la terre du ampamplificateur au châssis du véhicule.
- Use appropriate wire gauges for power, ground, and speaker connections as specified in this manual.
- Installez le ampInstaller l'amplificateur dans un endroit sec et bien ventilé, à l'abri de la lumière directe du soleil, des sources de chaleur et de l'humidité.
- Evitez de monter le amplifier in areas where it could interfere with vehicle operation or safety systems.
- N'essayez pas d'ouvrir ou de modifier le ampAmplificateur. Confiez toute intervention à un personnel qualifié.
- Protégez tous les câbles des arêtes vives et des pièces mobiles.
Contenu du colis
Vérifiez que tous les éléments sont présents dans le colis :
- DD Audio SS6000 Monoblock Amplifier
- Unité de contrôle de gain à distance
- Matériel de montage (vis, etc.)
- Manuel d'instructions (ce document)
Image: The remote gain control unit, featuring a voltage display, power indicator, clip indicator, and a rotary knob for gain adjustment.
Configuration et installation
1. Emplacement de montage
Choose a mounting location that is secure, dry, and provides adequate ventilation for the amplifier. Avoid mounting on carpet or in enclosed spaces without airflow. Ensure the amplifier is accessible for wiring and adjustments.
2. Connexions de câblage
Proper wiring is crucial for performance and safety. Refer to the diagram below for connection points.
Image : Haut et bas views of the DD Audio SS6000 ampamplificateur. Le haut view shows dual 0 AWG power and ground terminals. The bottom view displays RCA inputs, gain and filter controls (SENS, SUB SONIC, LPF), a remote port, and speaker output terminals.
- Puissance (BATT+) : Connect a 0 AWG power cable directly from the positive terminal of the vehicle's battery to the +12V terminals on the amplifier. Install an appropriate fuse (600A recommended) within 18 inches of the battery. The SS6000 features dual 0 AWG power terminals for robust current delivery.
- Masse (GND): Connect a 0 AWG ground cable from the GND terminals on the amplifier to a clean, unpainted metal surface of the vehicle chassis. The ground point should be as short as possible and securely fastened. The SS6000 features dual 0 AWG ground terminals.
- Télécommandé (REM) : Connect a 18 AWG or larger wire from the vehicle's head unit remote output to the REM terminal on the ampamplificateur. Ce fil transforme le ampL'amplificateur s'allume et s'éteint avec l'autoradio.
- Entrée RCA (ENTRÉE G/D) : Connectez les câbles RCA à la sortie pré-enregistrée de votre autoradio.amp outputs to the RCA INPUTs on the amplifier.
- Sortie haut-parleur (HAUT-PARLEUR) : Connect your subwoofer speaker wires (4 AWG recommended) to the SPEAKER terminals. Ensure correct polarity (+ to + and - to -). The SS6000 is a monoblock amplifier designed for a single channel output.
- Contrôle de gain à distance : Connect the included remote gain control unit to the "REMOTE" port on the amplifier using the provided cable.
Mode d'emploi
1. Initial Power-Up and Gain Setting
Une fois tous les branchements effectués, rebranchez la batterie du véhicule. Allumez votre autoradio. amplifier should power on (PWR indicator will illuminate). Begin with the amplifier's SENS (gain) control set to minimum (fully counter-clockwise) and the head unit volume at a low level.
- Play a familiar audio track.
- Increase the head unit volume to about 75-80% of its maximum.
- Slowly increase the SENS (gain) control on the amplifier until you hear distortion or the CLIP indicator on the remote gain control unit illuminates. Then, back off the gain slightly until the distortion disappears or the CLIP indicator turns off.
- The remote gain control unit allows for convenient adjustment of the ampNiveau de sortie de l'amplificateur depuis le siège conducteur.
2. Filter Adjustments
The SS6000 features adjustable filters to optimize sound quality for your subwoofer system:
- SUB SONIC (High Pass Filter): This filter removes extremely low frequencies that are inaudible or harmful to subwoofers. Adjust between 20Hz and 80Hz. A common setting is around 25-30Hz, depending on your subwoofer's capabilities and enclosure tuning.
- LPF (filtre passe-bas) : This filter allows only frequencies below the set point to pass to the subwoofer, preventing it from playing higher frequencies meant for full-range speakers. Adjust between 80Hz and 20kHz. Typically, for subwoofers, this is set between 80Hz and 120Hz, depending on the crossover point of your main speakers.
Entretien
The DD Audio SS6000 ampL'amplificateur nécessite un entretien minimal. Gardez-le amplifier clean and free of dust and debris. Periodically check all wiring connections for tightness and corrosion. Ensure that the ampLes ailettes de refroidissement de l'amplificateur ne sont pas obstruées afin de maintenir une dissipation thermique adéquate.
Dépannage
Si vous rencontrez des problèmes avec votre amplifier, consult the table below for common problems and solutions before contacting support.
| Problème | Cause possible | Solution |
|---|---|---|
| Amplifier does not turn on (no PWR light) | Pas d'alimentation, pas de mise à la terre, ni de signal à distance. Fusible grillé. | Check battery connections, ground connection, and remote wire. Verify fuse at battery is intact. |
| Pas de sortie audio | RCA cables disconnected, speaker wires disconnected, gain too low, head unit muted. | Check RCA and speaker connections. Adjust gain. Ensure head unit is playing audio. |
| Son déformé | Gain set too high, improper filter settings, poor quality audio source. | Reduce gain. Adjust SUB SONIC and LPF settings. Use a high-quality audio source. |
| Amplifier goes into protect mode (PRO light on) | Surchauffe, court-circuit dans le câblage du haut-parleur, impédance trop faible. | Ensure proper ventilation. Check speaker wiring for shorts. Verify speaker impedance is within amplifier's rated limits (1 Ohm minimum). |
| Noise (hissing, whining) | Ground loop, poor RCA shielding, power wire too close to signal wires. | Ensure good ground connection. Reroute RCA cables away from power wires. Consider a ground loop isolator if necessary. |
Caractéristiques
The following are the technical specifications for the DD Audio SS6000 Monoblock Amplifier :
| Fonctionnalité | Spécification |
|---|---|
| Modèle | SS6000 |
| Vol d'exploitationtage | 9 - 16 volts |
| Vol d'essaitage | 14.4 volts |
| Canaux de sortie | 1 (Monobloc) |
| Vat continutage @ 4 ohms | 2000 Watts RMS |
| Vat continutage @ 2 ohms | 4000 Watts RMS |
| Vat continutage @ 1 ohms | 6000 Watts RMS |
| Tirage de courant max. | 600 Amps |
| Vol d'entrée RCAtage Sensibilité | 0.4 - 4 volts |
| Rapport signal sur bruit (S/N) | >95 dB |
| DampFacteur | >100 |
| Distorsion harmonique totale (THD) | <1.0% |
| Réponse en fréquence | 20 - 20,000 Hz |
| Sub-Sonic Filter (HPF) | 20 - 80 Hz (12dB/Oct) |
| Filtre passe-bas (LPF) | 80 - 20,000 Hz (12dB/Oct) |
| Jauge de fil d'alimentation | 0 AWG (Dual Terminals) |
| Jauge de fil de haut-parleur | 4 AWG |
| Dimensions (L x l x H) | 11.25 x 7.3 x 2.4 pouces (286 x 185 x 60 mm) |
| Poids de l'article | 11 livres |
Garantie et assistance
For warranty information, please refer to the documentation provided with your purchase or visit the official DD Audio website. If you encounter issues not covered in the troubleshooting section, or require further assistance, please contact DD Audio customer support or your authorized dealer. Do not attempt to repair the amplifier yourself, as this may void your warranty.
