1. Introduction
Thank you for choosing the ECOELER 6-Inch Motion Sensor LED Ceiling Light. This manual provides detailed instructions for the safe installation, operation, and maintenance of your new lighting fixture. Please read this manual thoroughly before installation and retain it for future reference.
Illustration 1.1 : Avant view of the ECOELER 6-Inch Motion Sensor LED Ceiling Light.
2. Consignes de sécurité
Pour réduire les risques d'incendie, d'électrocution ou de blessures corporelles, suivez toujours ces précautions de sécurité de base :
- AVERTISSEMENT : Risque de choc électrique. Débranchez l'alimentation au niveau du fusible ou du disjoncteur avant l'installation ou l'entretien.
- Ce produit doit être installé conformément au code d’installation applicable par une personne connaissant la construction et le fonctionnement du produit ainsi que les dangers encourus.
- Use only 120V AC, 60Hz circuits.
- Ne tentez pas de démonter ou de modifier le dispositif. Il ne contient aucune pièce réparable par l'utilisateur.
- Assurez-vous que toutes les connexions sont sécurisées et correctement isolées.
- Ce luminaire convient uniquement à une utilisation en intérieur.
3. Contenu du colis
Vérifiez que tous les composants sont présents avant de commencer l'installation :
- 6-Inch Black Motion Sensor LED Ceiling Light (x1)
- Matériel de montage (vis, connecteurs de fils)
- E26 Adapter Accessories (for recessed can installation)
- Manuel d'instructions (ce document)
Image 3.1: Included accessories for installation.
4. caractéristiques du produit
- 3CCT sélectionnable : Choose between 3000K (Warm White), 4000K (Cool White), and 5000K (Daylight) color temperatures.
- Capteur de mouvement : Passive Infrared (PIR) sensor detects motion within 9-16 feet.
- Temporisation réglable : Set the light to remain on for 30 seconds, 1 minute, or 5 minutes after motion ceases.
- Capteur de lumière : The motion sensor functions only in dark environments, remaining off during daylight hours.
- Efficacité énergétique : 16W LED provides 1000 lumens of brightness.
- Installation polyvalente : Compatible with 3.5 or 4-inch junction boxes and 5 or 6-inch recessed cans.
Image 4.1: Key features including PIR sensor, 3CCT, and time delay settings.
5. Configuration et installation
Before installation, ensure the power supply is turned off at the circuit breaker.
5.1. Installation de la boîte de jonction
- Retirez l'objectif en le tournant dans le sens des aiguilles d'une montre.
- Connect the supply wires to the fixture wires using the provided wire nuts: black to black (live), white to white (neutral), and green/bare copper to green (ground).
- Attach the fixture base to the junction box using the provided screws.
- Twist the lens counter-clockwise to secure it back onto the fixture.
5.2. Recessed Can Installation
- Retirez l'objectif en le tournant dans le sens des aiguilles d'une montre.
- Install the spring clips onto the fixture base using screws.
- Connect the E26 adapter to the existing socket in the recessed can.
- Connect the fixture wires to the E26 adapter wires using wire nuts.
- Push the disk light into the recessed can until the spring clips secure it.
- Twist the lens counter-clockwise to secure it back onto the fixture.
Image 5.1: Installation diagrams for junction box and recessed can.
6. Mode d'emploi
After successful installation and restoring power, the light will be ready for operation. The ECOELER motion sensor light operates automatically based on ambient light and motion detection.
6.1. Fonctionnalités du capteur de mouvement
- Jour: The light remains off even if motion is detected, due to the integrated light sensor.
- Nighttime/Dark Environments: The light will automatically turn on when motion is sensed within its detection range (approximately 9-16 feet).
- The light will turn off after the set time delay if no further motion is detected.
Image 6.1: Motion sensor operation during day and night.
6.2. Réglage de la température de couleur (CCT)
The fixture offers three color temperature options: 3000K (Warm White), 4000K (Cool White), and 5000K (Daylight). To adjust the CCT:
- Assurez-vous que l’alimentation est coupée.
- Carefully remove the lens by twisting it clockwise.
- Locate the CCT selector switch on the LED board (refer to Image 4.1).
- Slide the switch to your desired color temperature setting (3000K, 4000K, or 5000K).
- Replace the lens by twisting it counter-clockwise.
- Restore power to test the new setting.
Image 6.2: Visual representation of 3CCT options.
6.3. Réglage du délai
The light can be set to remain on for 30 seconds, 1 minute, or 5 minutes after motion is no longer detected. To adjust the time delay:
- Assurez-vous que l’alimentation est coupée.
- Carefully remove the lens by twisting it clockwise.
- Locate the time delay selector switch on the fixture (refer to Image 4.1).
- Slide the switch to your desired time setting (30s, 1min, or 5mins).
- Replace the lens by twisting it counter-clockwise.
- Restore power to test the new setting.
Image 6.3: Time delay countdown feature.
7. Entretien
The ECOELER LED ceiling light requires minimal maintenance.
- Nettoyage: Assurez-vous que l'appareil est hors tension avant de le nettoyer. Essuyez-le avec un chiffon doux, sec ou légèrement humidifié.amp cloth. Do not use harsh chemicals or abrasive cleaners, as they may damage the finish or electronic components.
- Lentille: Keep the lens clean to ensure optimal light output and motion sensor performance.
8. Dépannage
If you experience issues with your ECOELER LED ceiling light, refer to the following common problems and solutions:
| Problème | Cause possible | Solution |
|---|---|---|
| La lumière ne s'allume pas. | No power supply; Incorrect wiring; Ambient light too bright; Motion sensor obstructed or faulty. | Check circuit breaker and wall switch. Verify wiring connections. Ensure installation is in a dark environment for sensor activation. Clear any obstructions from the sensor. |
| La lumière reste allumée en permanence. | Constant motion in detection area; Faulty motion sensor. | Ensure there is no continuous motion within the sensor's range. If the issue persists, contact customer support. |
| La lumière s'éteint trop vite ou trop lentement. | Le réglage du délai est incorrect. | Adjust the time delay switch to your desired setting (30s, 1min, or 5mins) as described in Section 6.3. |
| La lumière vacille ou faiblit de façon inattendue. | Loose wiring connection; Incompatible dimmer switch (this light is non-dimmable); Power fluctuations. | Check all wiring connections for tightness. Ensure no dimmer switch is being used. Consult an electrician if power fluctuations are suspected. |
9. Spécifications
| Marque | ÉCÉLER |
| Numéro de modèle | CDR616C-9P3X5BB |
| Dimensions du produit | 7.48"L x 7.48"l x 1.45"H |
| Poids de l'article | 11.3 onces |
| Couleur | Noir |
| Matériel | Acrylique, aluminium, plastique |
| Source d'énergie | Électrique avec fil |
| Voltage | 120 Volts (CA) |
| Quoitage | 16 watts |
| Luminosité | 1000 lumens |
| Couleur claire | 3CCT: 3000K (Warm White) - 4000K (Cool White) - 5000K (Daylight) |
| Type de contrôleur | Détecteur de mouvement |
| Caractéristiques spéciales | 30sec-1min-5min Countdown Timer Selectable, Adjustable Color Temperature, Energy Efficient, Motion Sensor, Shock Resistant |
| Type d'installation | Plafonnier |
| Certification | ETL, FCC |
10. Garantie et assistance
This ECOELER product is backed by a Limited Warranty. For specific warranty details and duration, please refer to the documentation included with your purchase or contact ECOELER customer support.
For technical assistance, troubleshooting, or warranty claims, please contact ECOELER customer support through the retailer where the product was purchased or visit the official ECOELER website.
Fabricant: ECOELER ELECTRIC INC
