Introduction
Thank you for choosing the BESTTEN Super Slim Dimmer Switch. This manual provides detailed instructions for the safe installation, operation, and maintenance of your new dimmer switch. Please read all instructions carefully before installation and retain this manual for future reference.
Image: Six BESTTEN Super Slim Dimmer Switches.
Consignes de sécurité
- AVERTISSEMENT: Pour éviter tout risque d'incendie, d'électrocution ou de décès, coupez le courant au niveau du disjoncteur ou du tableau électrique et vérifiez que le courant est bien coupé avant de procéder au câblage.
- Installer conformément à tous les codes électriques nationaux et locaux.
- Utilisez uniquement du fil de cuivre.
- Cet appareil est destiné à un usage intérieur uniquement.
- Ne pas utiliser avec des ampoules non dimmables.
- Maximum load: 300W for dimmable LED/CFL, 600W for incandescent/halogen.
- Only one dimmer switch can be installed per 3-way circuit.
Contenu du colis
- BESTTEN Super Slim Dimmer Switch (Quantity as purchased, e.g., 6 switches)
- Vis de montage
Note: Wall plates are not included and must be purchased separately.
Caractéristiques
| Paramètre | Valeur |
|---|---|
| Voltage | 120 V, 60 Hz |
| Dimmable LED/CFL Max. Load | 300 W |
| Incandescent/Halogen Max. Load | 600 W |
| Type de commutateur | Single Pole / 3-Way |
| Type de câblage | Wire Pigtails |
| Température de fonctionnement | 32 °C à 104 °C (0 °F à 40 °F) |
| Certifications | Répertorié ETL/cETL |
| Dimensions (L x l x H) | 4.13 x 1.73 x 0.87 pouces |
Image: Detailed specifications for the dimmer switch.
Image: Super Slim Design dimensions.
Image: Bulb compatibility and wattage évaluations.
Configuration et installation
Before beginning installation, ensure the power is turned off at the circuit breaker. This dimmer switch is designed for both single-pole and 3-way applications and does not require a neutral wire, making it suitable for older electrical systems.
Image: No neutral wire required feature.
Instructions de câblage
- Éteignez l'alimentation : Locate your circuit breaker or fuse box and turn off the power to the switch location. Verify power is off using a voltage testeur.
- Supprimer l'interrupteur existant : Retirez soigneusement l'ancien interrupteur du boîtier mural.
- Identifier les fils : Identify the Line (Hot), Load, Ground, and Traveler wires (for 3-way installations). It is recommended to take a picture of the existing wiring before disconnecting.
- Connectez les fils : Refer to the wiring diagrams below for single-pole and 3-way installations. Use wire nuts to secure connections.
- Fil noir : Connect to the Line (Hot) wire.
- Fil rouge : Connect to the Load wire.
- Fil vert : Connect to the Ground wire.
- Red & White wire: This wire is used only in 3-way installations. For single-pole installations, cap this wire with a wire nut. In 3-way installations, connect it to one of the Traveler wires.
- Installez le variateur : Gently push the wired dimmer switch into the wall box and secure it with the provided screws.
- Installer la plaque murale : Attach your desired wall plate (not included).
- Rétablir le courant : Remettez le courant au disjoncteur.
Image: Single Pole and 3-Way Wiring Diagrams.
Important pour les applications à 3 voies
For 3-way switches, there are three terminals besides the ground. One terminal is typically a different color than the other two. Label this wire as the Line/Load. The other two terminals connect to the Traveler wires. Caution: Only one dimmer switch can be installed in a 3-way circuit.
Mode d'emploi
The BESTTEN Super Slim Dimmer Switch features a rocker switch for ON/OFF control and a slide dimmer for brightness adjustment.
- Allumer/éteindre : Press the bottom part of the rocker switch to turn the lights ON, and the top part to turn them OFF.
- Réglage de la luminosité : Use the vertical slider on the side of the rocker switch to adjust the light level. Slide up for brighter light and down for dimmer light.
Dimming Range Setting (Sensitivity Dial)
To optimize performance and eliminate flickering with certain bulb types, you may need to adjust the dimmer's sensitivity dial. This small dial is located on the side of the dimmer switch, accessible after removing the wall plate.
- Turn on the switch and move the slide dimmer to its lowest (all the way down) setting.
- Rotate the Sensitivity Dial clockwise all the way down. NOTE: If the dial stops in either direction, do not continue to turn it.
- Rotate the Sensitivity Dial counter-clockwise slowly until the preferred lowest light level is achieved and the lights are not flickering.
Image: Dimming Range Setting with Sensitivity Dial.
Entretien
To maintain your dimmer switch, ensure power is off before cleaning. Wipe the surface with a soft, damp cloth. Do not use abrasive cleaners or solvents, as these can damage the finish or internal components. Regular inspection for loose connections or damage is recommended.
Dépannage
- Les lumières ne s'allument pas :
- Vérifiez le disjoncteur et assurez-vous que le courant est rétabli.
- Vérifiez que toutes les connexions filaires sont sécurisées.
- Ensure the bulb is functional and correctly installed.
- Lights flicker, hum, or buzz:
- Adjust the dimming range using the sensitivity dial as described in the 'Operating Instructions' section.
- Ensure your bulbs are specifically rated as 'dimmable'. Non-dimmable bulbs will not function correctly with a dimmer.
- Some dimmable LED/CFL bulbs may not be fully compatible with all dimmers. Consider trying a different brand or type of dimmable bulb.
- Assurez-vous que la quantité totale d'eautage of connected bulbs does not exceed the dimmer's maximum load capacity.
- Dimmer switch is warm to the touch:
- It is normal for dimmer switches to feel warm during operation. If the dimmer feels excessively hot, ensure the load does not exceed the maximum wattage note.
Image: Information on eliminating flickering.
Garantie et assistance
BESTTEN products are designed for reliability and performance. For warranty information or technical support, please refer to the manufacturer's official webConsultez le site ou contactez directement leur service client. Conservez votre reçu d'achat comme preuve d'achat.
Vous trouverez plus d'informations et les coordonnées en visitant le site web. Boutique BESTTEN sur Amazon.
