1. Introduction
Thank you for choosing the ELEGRP Decorator Triple Rocker Switch. This manual provides essential information for the safe installation, operation, and maintenance of your new switch. Please read these instructions thoroughly before beginning installation and retain them for future reference.
Informations importantes sur la sécurité
- AVERTISSEMENT : RISQUE DE CHOC ÉLECTRIQUE. Always turn off power at the circuit breaker or fuse box before installation, servicing, or removing the switch.
- Install in accordance with all national and local electrical codes. If you are unsure about any part of these instructions, consult a qualified electrician.
- Utiliser uniquement avec du fil de cuivre ou recouvert de cuivre.
- Ne pas utiliser dans des endroits humides.
- Assurez-vous que toutes les connexions filaires sont sécurisées.
2. caractéristiques du produit
The ELEGRP Decorator Triple Rocker Switch is designed for reliable performance and ease of use, offering control for three separate lighting loads from a single gang box.
- Rational Design: Features three smooth ON and OFF paddles with tactile feedback to prevent accidental operation.
- Construction de haute qualité : Made from impact-resistant polycarbonate thermoplastic and solid steel for extended durability.
- Mise à la terre automatique : Includes a self-grounding clip for automatic connection in properly grounded metal wall boxes.
- Installation facile : Supports both back wiring and side wiring. Features break-off plaster ears for flush alignment and a shallow body design to fit standard junction boxes.
- UL & CUL Listed: Strictly tested to UL Standards for safety and quality assurance.
Figure 1: Key features of the ELEGRP Triple Rocker Switch, highlighting its durable construction and safety certifications.
3. Contenu du colis
Vérifiez que tous les composants sont présents avant l'installation :
- 1 x ELEGRP Decorator Triple Rocker Switch (Model 72611-BL)
- 1 x Matching Wall Plate (Screw Wall Plate, Glossy Black)
- Vis de montage
4. Configuration et installation
Follow these steps carefully to install your ELEGRP Triple Rocker Switch.
Étapes de pré-installation
- Couper l'alimentation : Locate the circuit breaker or fuse that controls the switch location and turn off the power. Verify power is off using a voltage testeur.
- Retirer l'ancien interrupteur : Retirez soigneusement la plaque murale et l'interrupteur existants du boîtier mural. Débranchez les fils de l'ancien interrupteur.
- Inspecter le câblage : Identify the hot (line), neutral, ground, and load wires. If you are unsure, consult a qualified electrician.
Instructions de câblage
The ELEGRP Triple Rocker Switch offers two wiring options: side wiring and back wiring.
Figure 2: Wiring options for the switch, illustrating connections for hot, neutral, and ground wires.
- Fil de terre: Connect the green or bare copper ground wire from the wall box to the green grounding screw on the switch.
- Fil conducteur sous tension (ligne) : Connect the incoming hot (line) wire to the black screw terminal. This switch uses a common feed for all three loads.
- Câbles de charge : Connect the three load wires (one for each light/fixture) to the three brass screw terminals.
- Fil neutre : The neutral wire typically bypasses the switch and connects directly to the loads. Ensure proper neutral connections for your fixtures.
Montage du commutateur
- Repliez soigneusement les fils dans la boîte murale, en laissant suffisamment d'espace pour l'interrupteur.
- Insert the switch into the wall box and secure it with the provided mounting screws. Use the break-off plaster ears for flush alignment if needed.
- Attach the included wall plate over the switch and secure it with the smaller screws.
- Restaurer l'alimentation : Remettez le courant au niveau du disjoncteur ou du tableau électrique.
- Opération de test : Test each rocker paddle to ensure proper ON/OFF functionality for its respective load.
Figure 3: Compact design and dimensions of the switch, ensuring compatibility with standard wall boxes.
5. Mode d'emploi
The ELEGRP Decorator Triple Rocker Switch provides simple control for three independent lighting or appliance loads.
- Each of the three paddles operates independently.
- To turn a connected load ON, press the upper part of the corresponding paddle.
- To turn a connected load OFF, press the lower part of the corresponding paddle.
Figure 4: The triple rocker switch allows control of three separate loads from a single wall box, optimizing space.
6. Entretien
The ELEGRP Triple Rocker Switch requires minimal maintenance.
- Nettoyage: To clean the switch and wall plate, wipe with a soft, damp Chiffon. N’utilisez pas de nettoyants abrasifs ni de solvants, car ils pourraient endommager la finition.
- Inspection: Periodically check the switch and wall plate for any signs of damage or loose connections. If any issues are found, turn off power at the circuit breaker and address them promptly.
7. Dépannage
If you experience issues with your ELEGRP Triple Rocker Switch, refer to the following common troubleshooting steps:
| Problème | Cause possible | Solution |
|---|---|---|
| L'interrupteur ne s'allume/ne s'éteint pas. | L'interrupteur n'est pas alimenté. Connexion de fil lâche Faulty bulb/fixture | Check circuit breaker/fuse. Ensure power is restored. Turn off power, recheck all wire connections. Effectuez le test avec une ampoule/un luminaire dont le fonctionnement est avéré. |
| Switch feels loose in wall box | Vis de montage non serrées | Turn off power, tighten mounting screws securely. |
| Wall plate does not sit flush | Wires are too bulky in the box Switch not properly aligned | Carefully arrange wires to allow space. Adjust switch position in the wall box. |
If the problem persists after attempting these solutions, contact ELEGRP customer support or a qualified electrician.
8. Spécifications
| Spécification | Détail |
|---|---|
| Numéro de modèle | 72611-BL |
| Mode de fonctionnement | ALLUMÉ ÉTEINT |
| Évaluation actuelle | 15 Amps |
| Vol d'exploitationtage | 125 volts |
| Type de contact | Normalement ouvert |
| Type de connecteur | Clamp |
| Type de terminal | Clamp |
| Type de circuit | Parallèle |
| Type d'actionneur | Bascule |
| Dimensions du produit (L x l x H) | 7.17 x 4.41 x 3.46 pouces (18.21 x 11.20 x 8.79 cm) |
| Poids | 4.59 onces (130 grammes) |
| Certifications | Homologué UL et CUL |
9. Informations sur la garantie
ELEGRP products are manufactured to high-quality standards and are backed by a limited warranty against defects in materials and workmanship. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official ELEGRP website.
10. Assistance
For technical assistance, product inquiries, or warranty claims, please contact ELEGRP customer support through the following channels:
- En ligne: Visitez le site officiel ELEGRP Brand Store on Amazon.
- E-mail: Refer to your product packaging or the brand store for specific contact email.
