Introduction
This manual provides detailed instructions for the installation, configuration, and use of your VIMIN 10G PCI-E Network Card. Please read this manual thoroughly before installation to ensure proper operation and to maximize the performance of your network adapter.
Caractéristiques principales
- 10Gbps RJ45 Copper Port: Equipped with a Marvel AQC113 chipset, offering up to 10Gbps network speed for reliable high-speed data transfer.
- Rapid High-Speed Transmission: Supports PCIe 3.0 x4 bus interface, converting PCIe X4/X8/X16 slots into 10G RJ-45 Ethernet ports for efficient data transfer.
- Compatibilité multi-usages : Supports various data rates including 10Gbps, 5Gbps, 2.5Gbps, 1Gbps, and 100Mbps Ethernet connections with intelligent auto-negotiation.
- Flexible Bracket Adaptability: Includes both low-profile and standard brackets for compatibility with diverse computer chassis.
- Seamless System Support: Compatible with Windows 10/11, Windows Server, and Linux operating systems. Drivers are provided via a USB drive.
- Protocol Standard Compliance: Compliant with IEEE 802.3an, IEEE 802.3bz, IEEE 802.3ab, IEEE 802.3u, IEEE 802.3x, IEEE 802.3az, IEEE 802.1Q standards.
Contenu du colis
- 1 x VIMIN 10G PCI-E Network Card (AQC113)
- 1 x Standard Profile Support (préinstallé)
- 1 x Low-Profile Support
- 1 x Driver USB Drive
- 1 x Quick Installation Guide (This manual serves as a detailed guide)
Installation du matériel
- Éteignez votre ordinateur et débranchez le câble d'alimentation.
- Ouvrez le boîtier de l'ordinateur.
- Locate an available PCI Express x4, x8, or x16 slot on your motherboard.
- Remove the corresponding slot cover from the computer chassis. If necessary, replace the standard bracket on the network card with the low-profile support.
- Carefully insert the VIMIN 10G PCI-E Network Card into the chosen PCIe slot until it is firmly seated.
- Secure the network card with a screw to the computer chassis.
- Fermez le boîtier de l'ordinateur et rebranchez le câble d'alimentation.
- Connect an Ethernet cable to the RJ45 port on the network card.
This image illustrates the three main steps for hardware installation: 1. Opening the chassis and removing the slot limiter. 2. Inserting the PCIe card into the slot. 3. Securing the bracket with screws.
The network card comes with both standard and low-profile brackets to fit various computer cases. It is compatible with PCI Express x4, x8, and x16 slots.
Installation du pilote
After hardware installation, you will need to install the appropriate drivers for your operating system.
- Démarrez votre ordinateur.
- Insert the provided USB drive containing the drivers.
- Navigate to the USB drive and locate the driver folder corresponding to your operating system (Windows, Linux).
- Follow the on-screen instructions to install the drivers. For Windows, run the setup executable. For Linux, consult the README file within the driver folder for specific commands.
- Redémarrez votre ordinateur une fois l'installation du pilote terminée.
Note: In some cases, especially with newer Linux distributions, the driver may be automatically recognized and installed by the system.
Compatibilité du système d'exploitation
The VIMIN 10G PCI-E Network Card supports a wide range of operating systems:
- Windows 10
- Windows 11
- Windows Server (various versions)
- Linux (various distributions)
- VMware
This network card is compatible with Windows 10/11, Windows Server, and Linux operating systems.
Spécifications techniques
| Fonctionnalité | Détail |
|---|---|
| Numéro de modèle | AQC113 |
| Marque | VIMIN |
| Interface matérielle | Ethernet |
| Protocole de liaison de données | Ethernet |
| Taux de transfert de données | 10 gigabits par seconde (10 Gbit/s) |
| Compatible Data Rates | 10Gbps/5Gbps/2.5Gbps/1Gbps/100Mbps |
| Jeu de puces du contrôleur | Marvel AQC113 |
| Interface PCI Express | PCIe 3.0 x4 (Compatible with X4, X8, X16 slots) |
| Ports | 1 x RJ45 Copper Port |
| Appareils compatibles | Desktop, Laptop (with available PCIe slot) |
| Systèmes d'exploitation pris en charge | Windows 10/11, Windows Server, Linux, VMware |
| Normes de protocole | IEEE 802.3an, IEEE 802.3bz, IEEE 802.3ab, IEEE 802.3u, IEEE 802.3x, IEEE 802.3az, IEEE 802.1Q |
| Dimensions du colis | 5.79 x 5.12 x 1.1 pouces |
| Poids de l'article | 5.3 onces (0.15 kilogrammes) |
| Couleur | Noir |
Dépannage
No Network Connection After Installation
- Verify Hardware Installation: Ensure the network card is fully seated in the PCIe slot and securely fastened.
- Vérifier la connexion du cable: Confirm the Ethernet cable is properly connected to both the network card and your router/switch.
- Installation du pilote : Make sure the correct drivers for your operating system have been installed. Refer to the "Driver Installation" section.
- Gestionnaire de périphériques (Windows) : Check Device Manager to see if the network card is recognized and if there are any error symbols (e.g., yellow exclamation mark). Reinstall drivers if necessary.
- Paramètres BIOS/UEFI : Ensure the PCIe slot is enabled in your system's BIOS/UEFI settings.
Débits de réseau lents
- Qualité du câble : Use a high-quality Cat6a or Cat7 Ethernet cable for 10Gbps connections. Lower category cables may limit speed.
- Compatibilité routeur/commutateur : Ensure your network router or switch supports 10Gbps speeds on the connected port.
- Mises à jour du pilote: Check for the latest drivers from the VIMIN website or the provided USB drive.
- Ressources système : High CPU usage or insufficient RAM on your computer can affect network performance.
Card Not Detected in Windows 11
- Bande passante de l'emplacement PCIe : Some motherboards share bandwidth between PCIe slots and M.2 NVMe slots. If the card is not detected, try moving it to a different PCIe slot or temporarily removing other M.2 devices to check for conflicts.
- Manual Driver Update: If the card appears in Device Manager but has issues, try manually updating the driver by searching for the Intel 10 Gigabit Ethernet driver pack and pointing Device Manager to the extracted driver files.
Garantie et assistance technique
The VIMIN 10G PCI-E Network Card comes with a 1-year after-sale service.
Pour toute assistance technique, dépannage ou question relative à la garantie, veuillez contacter notre équipe d'assistance :
- E-mail: support@vimintech.com
- Support en ligne: Visit the official VIMIN webSite de FAQ et de ressources supplémentaires.
VIMIN offers dedicated customer support via email at support@vimintech.com, backed by a professional technical team providing 24-hour service.
Consignes de sécurité
- Always power off your computer and disconnect the power cable before installing or removing any internal components.
- Handle the network card by its edges to avoid touching the gold-plated connectors or sensitive components.
- Utilisez les précautions antistatiques appropriées (par exemple, un bracelet antistatique) pour éviter les dommages causés par les décharges électrostatiques (DES).
- Ensure proper ventilation within your computer case to prevent overheating, especially for high-performance components.
- N’essayez pas de modifier ou de réparer l’appareil vous-même. Confiez toute intervention à un technicien qualifié.
Produit terminéview Vidéo
Cette vidéo offre un aperçu visuelview of the VIMIN 10G PCI-E Network Card, highlighting its key features, installation process, and high-speed capabilities.
