Manuel d'utilisation du contrôleur ZTW Mantis Slim G2 15 A

1. Avertissements de sécurité importants

WARNING: THIS ESC IS NOT A TOY. It is a high-power electronic component for use by knowledgeable hobbyists. Misuse can cause property damage, personal injury, or fire. NEVER short-circuit the battery terminals (+ and -). This will cause extreme heat, fire, or explosion. DISCONNECT the battery immediately after use.

Always ensure proper ventilation around the ESC during operation. Do not operate the ESC in wet conditions. Read this manual completely before installation and operation.

2. Présentation du produit

The ZTW Mantis Slim G2 15A Electronic Speed Controller (ESC) is designed for micro to small-sized RC airplanes and drones. It features a compact and lightweight design, providing reliable and efficient power delivery for various flight applications, including F3P, 3D, and 4D flying. This ESC incorporates advanced technology for smooth operation and multiple protection features to ensure safety and longevity.

Image 1: ZTW Mantis Slim G2 15A ESC showing the product label and wire connections.

3. Principales caractéristiques

• High-Efficiency 15A Output: Delivers a continuous 15A current for stable performance.
• Integrated 5V/3A Switching BEC: Provides clean, stable power to the receiver and servos, preventing brown-outs.
• Conception ultra-compacte et légère : Allows for easy installation in tight spaces, maintaining optimal model balance.
• Comprehensive Protection Suite: Comprend un faible volumetage Cutoff (LVC) and Over-Heat protection to prevent damage.
• Smooth Operation & Wide Compatibility: Offers smooth throttle response and is compatible with 2-4S LiPo battery setups and various sensorless brushless motors.
• Programmable: Supports programming via transmitter or ZTW LCD programming card (sold separately).

4. Spécifications

5. Configuration et installation

Follow these steps for proper installation of your ZTW Mantis Slim G2 15A ESC:

1. Raccordement au moteur : Connect the three motor wires from the ESC to the three wires of your brushless motor using the 2.0mm bullet connectors. The order of connection may affect motor rotation direction; if the motor spins in the wrong direction, swap any two of the motor wires.
2. Se connecter au récepteur : Plug the servo lead (signal cable) from the ESC into the throttle channel of your RC receiver. This is typically channel 3.
3. Connexion à la batterie : Connect your 2-4S LiPo battery (or 5-12NC battery) to the JST female connector on the ESC. Ensure correct polarity.
4. Secure the ESC: Mount the ESC securely in your aircraft, ensuring good airflow for cooling. Avoid placing it near sources of interference.

Image 2 : Terminéview of the ZTW Mantis Slim G2 15A ESC showing all connection points: battery (JST), receiver (servo lead), and motor (bullet connectors).

6. Mode d'emploi

6.1 Calibrage de la plage d'accélération

For optimal performance, calibrate the ESC's throttle range with your transmitter:

1. Turn on your transmitter and set the throttle stick to its maximum position (100% throttle).
2. Connectez la batterie au contrôleur de vitesse électronique (ESC). L'ESC émettra une série de bips.
3. When you hear the confirmation beeps (usually a long beep or a specific tone sequence), move the throttle stick to its minimum position (0% throttle).
4. The ESC will emit another series of beeps to confirm the minimum throttle position. The calibration is now complete.

6.2 Modes de programmation

The ZTW Mantis Slim G2 15A ESC supports two main operating modes:

• Transférer uniquement : Standard mode for fixed-wing aircraft.
• Avant et arrière : For specific 3D/4D flying applications where reverse thrust is required.

Programming can be done via your transmitter's stick commands or more conveniently with the ZTW LCD Program Card G2 (sold separately). Refer to the program card's manual for detailed instructions on adjusting parameters such as battery type, cutoff voltage, timing, and brake settings.

7. Entretien

• Keep the ESC clean and free from dust, dirt, and moisture.
• Inspectez régulièrement tous les fils et connecteurs pour détecter tout dommage ou connexion desserrée.
• Ensure adequate airflow around the ESC to prevent overheating, especially during prolonged use.
• Rangez le contrôleur de vitesse électronique (ESC) dans un endroit sec et frais lorsqu'il n'est pas utilisé.

8. Dépannage

If you encounter issues with your ESC, consider the following:

• Le moteur ne tourne pas : Check all connections (battery, motor, receiver). Ensure the throttle is calibrated correctly. Verify the battery is charged.
• Erratic motor behavior/stuttering: This could indicate incorrect motor timing, a loose connection, or a damaged motor/ESC. Check connections and try adjusting motor timing if programmable.
• Surchauffe du contrôleur de vitesse électronique (ESC) : Ensure sufficient airflow. Check for excessive current draw from the motor or an undersized propeller.
• No power to receiver/servos: Check the BEC output. Ensure the ESC is properly connected to the receiver.
• ESC beeps continuously: This often indicates a low voltage cutoff or an error code. Refer to the programming card manual for specific beep codes if available.

If problems persist, contact ZTW customer support for further assistance.

9. Garantie et assistance

For warranty information and technical support, please refer to the official ZTW webConsultez le site web ou contactez votre revendeur. Conservez votre preuve d'achat pour toute réclamation au titre de la garantie.