Informations importantes sur la sécurité
Please read and understand all instructions and safety warnings before assembly and use of this product. Failure to follow these instructions may result in injury or product damage.
- Do not attempt to lift or move the box spring when it is fully assembled.
- Suivez toujours attentivement les instructions de montage afin d'éviter toute instabilité ou tout effondrement.
- Be cautious of sharp edges and the folding design during assembly and use.
- Regularly inspect the box spring for any signs of wear or damage.
- Ne dépassez pas la capacité de poids maximale de 3500 lb.
Contenu du colis
Vérifiez que tous les composants sont présents avant de commencer l'assemblage.
- Box Spring Frame Components
- Couverture en tissu
- Manuel d'installation
- Vis
- Clé
Configuration et assemblage
The MAF King Size Box Spring features a foldable design for easier setup. It is recommended that two adults assemble this product.
Outils requis :
- Clé incluse
- (Optional) Power screwdriver for faster assembly
Étapes d'assemblage :
- Déballer les composants : Retirez soigneusement toutes les pièces de leur emballage et disposez-les sur une surface propre et plane. Vérifiez que tous les composants mentionnés sont présents.
- Dépliez le cadre : The box spring frame comes in a folded configuration. Gently unfold the sections as shown in the diagram below. Ensure the triangular support designs lock into place.
- Connexions sécurisées : Align the frame sections and secure them using the provided screws and wrench. Ensure all connections are tightened securely to prevent wobbling or noise.
- Installer les lattes : Place the metal slats into their designated positions on the frame. The U-shaped groove design helps secure each pole and support frame.
- Appliquer la housse en tissu : Once the frame is fully assembled and stable, carefully place the removable fabric cover over the box spring. The cover is designed for easy application and removal.
Figure 1: Assembly Steps for the MAF Box Spring.
Figure 2: Foldable Design and Easy Assembly Overview.
Figure 3: Key Structural Features: Round Corners, Triangular Support, and U-Shaped Grooves.
Mode d'emploi
The MAF Box Spring is designed to provide stable support for your mattress. It can be used with various mattress types, including innerspring, memory foam, and latex mattresses.
- Placement: Position the assembled box spring on a compatible bed frame or directly on the floor if desired. Ensure it is level and stable.
- Placement du matelas : Carefully place your mattress on top of the box spring. The box spring is designed to support mattresses up to 80"L x 76"W.
- Capacité de poids : The box spring is engineered to support up to 3500 lbs. Do not exceed this weight limit to maintain structural integrity and safety.
- Réduction du bruit : The U-shaped groove design and seamless welding are intended to prevent structural distortion and squeaks, providing a quiet sleeping environment.
Figure 4: Proper Layering of Bed Components.
Entretien et soins
Proper maintenance ensures the longevity and performance of your MAF Box Spring.
- Nettoyage du couvercle : The fabric cover is removable and washable. Remove it from the frame for cleaning as needed. Follow care instructions on the cover label if available, or wash with mild detergent and cold water, then air dry.
- Nettoyage du cadre : Essuyez le cadre métallique avec un chiffon sec pour enlever la poussière et les débris. Évitez d'utiliser des produits chimiques agressifs ou des nettoyants abrasifs.
- Inspection régulière : Periodically check all screws and connections to ensure they remain tight. Re-tighten if necessary. Inspect the frame for any signs of bending, cracks, or damage.
- Moving the Box Spring: If you need to move the box spring, it is recommended to disassemble it first, especially if moving through narrow doorways or stairs, to prevent damage to the product or injury.
Dépannage
If you encounter any issues with your MAF Box Spring, refer to the following common solutions:
| Problème | Cause possible | Solution |
|---|---|---|
| Bruit de grincement | Connexions desserrées ou placement inégal. | Ensure all screws are tightly secured. Verify the box spring is placed on a flat, level surface. The U-shaped groove design is intended to minimize noise; if squeaking persists, re-check assembly. |
| Instabilité/oscillation | Incomplete assembly or damaged components. | Re-check all assembly steps, ensuring triangular supports are engaged and all fasteners are tight. Inspect for any bent or damaged parts. |
| Mattress Sagging | Exceeded weight capacity or improper mattress support. | Ensure the combined weight of users and mattress does not exceed 3500 lbs. Verify the mattress is compatible with a box spring. |
Caractéristiques
| Fonctionnalité | Détail |
|---|---|
| Marque | MAF |
| Numéro de modèle | MAF-MT33-10K |
| Taille | Roi |
| Dimensions du produit | 78.8"L x 75.5"l x 10"H |
| Taille de matelas compatible | 80 po L x 76 po l |
| Dossier spécial | Foldable Design, Round Corner Design, Triangular Support, U-Shaped Groove Design |
| Type de finition | Revêtement en poudre |
| Composants inclus | Box Spring Frame, Fabric Cover, Installation Manual, Screws, Wrench |
| Instructions d'entretien du produit | Wipe with Dry Cloth, Removable and Washable Fabric Cover |
| Assemblage requis | Oui |
| Distance entre le sol et l'objet | 10 pouces |
| Poids de l'article | 49.1 livres |
| Capacité de poids maximale | 3500 livres |
Figure 5: MAF Box Spring Size Chart.
Garantie et assistance
Specific warranty details for the MAF Box Spring are not provided within this manual. For warranty information, please refer to the product packaging or contact MAF customer support directly.
For further assistance, questions, or to report any issues, please visit the official MAF store or contact their customer service department.
