1. Produit terminéview
The TOA Electronics VX-3004F AMQ is a voice alarm system frame designed for use with TOA's VX-3000 Series rack-mount type voice evacuation systems. This unit complies with the European Standard EN54-16 for fire alarm systems, providing control for voice evacuation announcements and status indications.
It supports up to 4 amplifiers, configurable as 1 zone with 1 amplifier, 4 AB-zones, or 3 AB zones with a standby amplifier. The front panel features various indicators for amplifier status, fault conditions, and system operation, along with control buttons for acknowledgment, reset, and lamp essai.
2. Disposition du panneau avant
Figure 1 : Front Panel of the VX-3004F AMQ Voice Alarm System Frame.
The front panel of the VX-3004F AMQ provides visual feedback on the system's operational status and allows for basic control. Key areas include:
- TOA Logo: Brand identification on the upper left.
- Amplifier Status Indicators: Located on the lower left, these LEDs show the status for up to four amplifiers (1, 2, 3, 4/SBY). Each amplifier has indicators for CULMINER (overload), SIGNAL (audio presence), FONCTIONNER (active), and POUVOIR (au).
- Fault Status Indicators: Positioned in the center, these LEDs indicate various system faults. They are categorized by ZONE (A and B, with indicators for 1, 2, 3, 4) and GÉNÉRAL faults (FUSIBLE, POUVOIR, Processeur, UNITÉ, RÉSEAU, EMG MIC).
- Boutons de contrôle : Three buttons are located to the right of the fault status indicators: ACCUSÉ (Acknowledge), RÉINITIALISER, et LAMP TEST.
- Indicateurs d'état du système : On the upper right, these LEDs show overall system status: POUVOIR (main power), COURIR (system operating), URGENCE (emergency mode active), and CPU OFF (CPU not running).
- Network/Link Indicators: Below the system status, LEDs for LAN A, LAN B, RS LINK A, et RS LINK B indicate network and communication link activity.
- Numéro de modèle : "VOICE EVACUATION FRAME VX-3004F" is printed on the lower right.
3. Installation et configuration
3.1. Déballage et inspection
Carefully unpack the VX-3004F AMQ frame and inspect it for any signs of damage during transit. Ensure all components listed in the packing materials are present. If any damage or missing parts are found, contact your supplier immediately.
3.2. Montage
The VX-3004F AMQ is designed for rack-mount installation. Secure the unit into a standard 19-inch equipment rack using appropriate mounting hardware. Ensure adequate ventilation around the unit to prevent overheating.
3.3. Connexion électrique
Connect the unit to a 20 - 33 V DC power source using the removable 4-pin terminal block. Ensure correct polarity and a stable power supply. The power consumption is 24 W for the frame only, and up to 90 W when RS Link is outputting 2A.
3.4. Network and Link Connections
- LAN A, B: Connect standard 100BASE-TX network cables to the RJ45 connectors for network communication.
- RS Link A, B: Use shielded Category 5 twisted pair (CAT5-STP) or greater cables for RS Link connections. These provide power feed up to 1A per connector.
- DS Link: Connect to DS LINK of power supply units using shielded Category 5 twisted pair (CAT5-STP) cables.
- Analog Link: Connect to other VX-3004F, VX-3008F, or VX-3016F units via the RJ45 connectors for analog input/output.
4. Fonctionnement
4.1. Mise sous tension
Once all connections are secure, apply power to the unit. The POUVOIR indicator on the front panel should illuminate. After a brief initialization period, the COURIR indicator will light up, signifying normal operation.
4.2. Amplifier Status Monitoring
Surveiller le amplifier status indicators for each of the four ampcanaux lificateurs :
- PIC: S'allume lorsque le amplifier output level is too high, indicating potential distortion.
- SIGNAL: Illuminates when an audio signal is present at the amplifier l'entrée.
- FONCTIONNER: S'allume lorsque le amplifier is active and functioning.
- POUVOIR: S'allume lorsque le amplifier module has power.
4.3. Fault Status Monitoring
Le ÉTAT DE DÉFAUT section provides critical information regarding system health. If any fault indicator illuminates, refer to the Troubleshooting section.
- ZONE A/B (1-4): Indicates a fault within a specific speaker zone (A or B) for channels 1 through 4.
- FUSIBLE: Indicates a blown fuse within the unit.
- POUVOIR: Indicates a power supply issue.
- Processeur: Indicates a central processing unit malfunction.
- UNITÉ: Indicates a general unit fault.
- RÉSEAU: Indicates a network communication error.
- EMG MIC: Indicates a fault with the emergency microphone.
4.4. Boutons de commande
- ACK (Acknowledge): Press to acknowledge a fault condition, which may silence an audible alarm or clear a flashing indicator.
- RÉINITIALISER: Press to reset the system after a fault has been resolved.
- LAMP TEST: Press and hold to illuminate all LED indicators on the front panel, verifying their functionality.
5. Entretien
5.1. Nettoyage
Regularly clean the exterior of the unit with a soft, dry cloth. Do not use liquid cleaners or abrasive materials. Ensure ventilation openings are free from dust and obstructions.
5.2. Conditions environnementales
Ensure the unit is operated within its specified temperature and humidity ranges. Avoid exposing the unit to direct sunlight, excessive heat, moisture, or corrosive environments.
5.3. Mises à jour du micrologiciel
Periodically check the TOA Electronics website for any available firmware updates for the VX-3004F AMQ. Follow the provided instructions carefully for any update procedures.
6. Dépannage
This section provides guidance for common issues indicated by the front panel fault status LEDs.
| Indicateur | Cause possible | Action |
|---|---|---|
| POUVOIR (System Status) Off | No DC power supply, power cable disconnected. | Check DC power source and cable connections. |
| COURIR Désactivé | System initialization failure, CPU error. | Check CPU fault indicator. Power cycle the unit. If issue persists, contact support. |
| CULMINER (Amplifier) On | Amplifier input signal too high, output overload. | Reduce input signal level or check speaker line impedance. |
| ZONE A/B (Fault Status) On | Fault detected in the specified speaker zone (e.g., open circuit, short circuit). | Inspect speaker lines and connections for the indicated zone. |
| FUSIBLE (Fault Status) On | Fusible interne grillé. | Contact qualified service personnel for fuse replacement. Do not attempt to replace fuses yourself. |
| POUVOIR (Fault Status) On | Internal power supply malfunction. | Power cycle the unit. If the fault persists, contact support. |
| Processeur (Fault Status) On | Central Processing Unit error. | Power cycle the unit. If the fault persists, contact support. |
| RÉSEAU (Fault Status) On | Network communication error. | Check LAN cable connections and network configuration. |
| EMG MIC (Fault Status) On | Emergency microphone fault. | Check emergency microphone connection and functionality. |
After resolving a fault, press the ACCUSÉ button to acknowledge the fault and then the RÉINITIALISER button to clear the fault condition and restore normal operation.
7. Spécifications
| Fonctionnalité | Détail |
|---|---|
| Modèle | VX-3004F AMQ |
| Source d'énergie | 20 - 33 V DC, removable terminal block (4 pins) |
| Consommation d'énergie | 24 W (frame only) at 33V DC input, 90 W (RS Link: 2 A output) at 33 V DC input |
| LAN A, B | 2 Connectors, 100BASE-TX, TCP, UDP, ARP, ICMP, RTP, IGMP, FTP, HTTP, NTP, RSTP, PCM (48 kHz, 16 bits) |
| RS Link A, B | 2 Connectors, Max. 1 A power feed per connector, RJ45, Shielded Category 5 twisted pair cable (CAT5-STP) or greater |
| DS Link | RJ45, Shielded Category 5 twisted pair cable (CAT5-STP) |
| Analog Link | 1 input, 1 output, RJ45 (for VX-3004F, VX-3008F, VX-3016F) |
| Finition | Panel: Surface-treated steel plate, black, 30 percent gloss, paint |
| Dimensions (L x l x H) | 13.58 x 19.02 x 5.22 pouces (34.5 x 48.3 x 13.25 cm) |
| Poids | 16.76 livres (7.6 kg) |
| Conformité | EN54-16 |
8. Garantie et assistance
8.1. Informations sur la garantie
For detailed warranty information regarding your TOA Electronics VX-3004F AMQ, please refer to the warranty card included with your product or contact your authorized TOA Electronics dealer or distributor. Warranty terms and conditions may vary by region and purchase location.
8.2. Assistance technique
Should you encounter any issues not covered in this manual or require further technical assistance, please contact your local TOA Electronics technical support or authorized service center. Ensure you have your product model number (VX-3004F AMQ) and serial number available when seeking support.
