Globo Lighting BOSTON Outdoor Pedestal Light

1. Introduction

Thank you for choosing the Globo Lighting BOSTON Outdoor Pedestal Light. This manual provides essential information for the safe installation, operation, and maintenance of your new lighting fixture. Please read these instructions carefully before installation and retain them for future reference.

Image 1.1: The BOSTON outdoor pedestal light providing illumination along a pathway.

2. Consignes de sécurité

• Sécurité électrique : L'installation doit être effectuée par un électricien qualifié, conformément aux normes électriques locales et nationales en vigueur. Coupez toujours l'alimentation au disjoncteur principal avant toute installation, maintenance ou remplacement d'ampoule.
• Utilisation en extérieur : This fixture is designed for outdoor use. Ensure all connections are waterproof and sealed appropriately to prevent water ingress.
• Type d'ampoule : Use only E27 bulbs with the specified wattage. Ne dépassez pas la puissance maximaletage indiqué sur le luminaire.
• Manutention: Manipulez le luminaire avec précaution. Évitez de le faire tomber ou de le soumettre à des chocs violents.
• Nettoyage: N’utilisez pas de nettoyants abrasifs ni de solvants. Nettoyez avec un chiffon doux et sec.amp tissu.
• Chaleur: Laissez l'ampoule refroidir complètement avant d'essayer de la remplacer.

3. Contenu du colis

Veuillez vérifier que tous les composants sont présents et non endommagés avant de commencer l'installation :

• 1x BOSTON Outdoor Pedestal Light Fixture (Model 105701)
• 1x socle de montage
• 1x Set of Mounting Hardware (screws, anchors)
• 1x Manuel d'utilisation

Note: E27 bulb is not typically included and must be purchased separately.

4. Spécifications

5. Configuration et installation

Important: Ensure the main power supply is switched off at the circuit breaker before commencing installation.

1. Choisissez l'emplacement: Select a suitable outdoor location for the pedestal light, ensuring it is on a stable, level surface and has access to the necessary electrical wiring.
2. Préparation du câblage : If not already present, run appropriate outdoor-rated electrical cable to the installation point. Consult a qualified electrician for this step.
3. Montez la base : Position the mounting base on the desired surface. Mark the drilling points through the holes in the base. Drill pilot holes and secure the base using the provided mounting hardware (screws and anchors). Ensure the base is firmly attached.
4. Connectez les fils électriques : Carefully connect the electrical wires from your power supply to the terminals inside the fixture. Follow the standard wiring color codes (e.g., Live, Neutral, Earth). Ensure all connections are secure and properly insulated.
5. Installez l'ampoule : Insert a suitable E27 bulb (not included) into the lamp titulaire. Ne pas trop serrer.
6. Fixation sécurisée : Attach the main body of the pedestal light to the mounted base, ensuring it is securely fastened and sealed against moisture.
7. Restaurer l'alimentation : Une fois l'installation terminée et toutes les connexions sécurisées, rétablissez le courant au niveau du disjoncteur principal.

Image 5.1: The pedestal light installed on a patio, demonstrating a typical mounting scenario.

6. Mode d'emploi

The BOSTON Pedestal Light features an integrated motion sensor for automatic operation.

• Mise sous tension : Once installed and power is restored, the light will enter a warm-up period (typically a few seconds) before the motion sensor becomes active.
• Capteur de mouvement : The integrated motion sensor detects movement within its detection range. When motion is detected, the light will illuminate.
• Arrêt automatique: After a period of no detected motion, the light will automatically turn off. The duration of illumination is typically pre-set or adjustable via controls on the sensor (if available). Refer to the sensor's specific markings for adjustment options.
• Capteur jour/nuit : The motion sensor also includes a photocell that prevents the light from activating during daylight hours, conserving energy. The light will only activate due to motion when ambient light levels are low enough.

Image 6.1: Detail of the motion sensor on the pedestal light, highlighting its detection area.

Image 6.2: The pedestal light operating at night, with the motion sensor detecting movement.

7. Entretien

• Nettoyage: Nettoyez régulièrement le luminaire avec un chiffon doux.amp cloth to remove dirt and debris. Do not use harsh chemicals or abrasive materials, as these can damage the finish or plastic components.
• Remplacement de l'ampoule :
  1. Ensure the power supply to the fixture is turned off at the circuit breaker.
  2. Laissez l'ampoule usagée refroidir complètement avant de la toucher.
  3. Carefully unscrew the top cover or access panel to reach the E27 bulb.
  4. Unscrew the old bulb and replace it with a new E27 bulb of the correct wattage.
  5. Securely reattach the cover or access panel, ensuring a watertight seal.
  6. Rétablir le courant.
• Inspection: Periodically inspect the fixture for any signs of wear, damage, or loose connections. Address any issues promptly to ensure continued safe operation.

8. Dépannage

If you experience persistent issues not covered here, please contact a qualified electrician or the product supplier.

9. Garantie et assistance

This product is covered by the standard warranty provided by the manufacturer. Please retain your proof of purchase for any warranty claims. For technical support or further assistance, please contact your retailer or the Globo Lighting customer service department.

Les coordonnées se trouvent généralement sur l'emballage du produit ou sur le site officiel du fabricant. website.