Pulsar PGiPAIRB4 Inverter Generator Parallel Kit

Introduction

This manual provides essential instructions for the safe and efficient use of your Pulsar PGiPAIRB4 Inverter Generator Parallel Kit. This kit allows you to connect two compatible Pulsar inverter generators to double their power output, providing increased electrical capacity for various applications, including RV use.

Compatible Pulsar Generator Models: PGDA70BiSCO, PGD95BiSCO, PGD105TiSCO.

Consignes de sécurité

Always read and understand all safety warnings and instructions in this manual and the manuals of your connected generators before operation. Failure to follow these instructions can result in serious injury or property damage.

• Ensure all connections are secure before starting generators.
• Operate generators in a well-ventilated area to prevent carbon monoxide poisoning.
• Ne pas utiliser dans des conditions humides.
• Keep children and pets away from operating equipment.
• Always turn off generators and disconnect spark plug wires before performing any maintenance or making connections.

Contenu du colis

Vérifiez que tous les éléments sont présents dans votre colis :

• Pulsar PGiPAIRB4 Parallel Kit Unit
• Connection Cables (integrated)
• Manuel de l'utilisateur (ce document)

Image: The Pulsar PGiPAIRB4 Parallel Kit unit, showing the main box with receptacles and circuit breakers, and the integrated connection cables extending from it.

Installation et connexion

Follow these steps to connect your parallel kit to two compatible Pulsar inverter generators:

1. Préparation: Ensure both generators are turned off, cooled down, and disconnected from any loads. Place the generators on a level, stable surface in a well-ventilated area.
2. Connect Parallel Cables: Locate the parallel connection ports on each generator. These are typically color-coded (red and black) and may have specific shapes.
   

   Image : Un gros plan view of the parallel kit's connection cables, showing the red and black connectors designed to plug into the generators.
   Connect the red cable from the parallel kit to the red parallel port on the first generator. Connect the black cable from the parallel kit to the black parallel port on the first generator. Repeat this process for the second generator.
   

   Image: Various parallel connection adapters and plugs, illustrating the types of connections used for linking generators.

3. Connexions sécurisées : Ensure all connections are firmly seated and secure. Loose connections can cause arcing or power interruptions.
4. Placement final : Position the parallel kit unit in a safe, accessible location, away from exhaust fumes and moisture.
   

   Image: Two Pulsar inverter generators shown from the rear, with the PGiPAIRB4 Parallel Kit connected to their respective parallel ports, demonstrating a complete setup.

Mode d'emploi

Once the parallel kit is securely connected to both generators:

1. Start Generators: Start both inverter generators according to their individual operating instructions. Allow them to run for a few moments to stabilize.
2. Charges de connexion : Plug your electrical loads into the receptacles on the PGiPAIRB4 Parallel Kit.
   • The L14-50 receptacle provides 120/240V output at 50 amps.
   • The L14-30 receptacle provides 120/240V output at 30 amps.
3. Moniteur: Observe the generator and parallel kit for proper operation. The circuit breakers on the parallel kit will trip if an overload occurs.
4. Fermer: To shut down, first disconnect all loads from the parallel kit. Then, turn off both generators according to their individual instructions. Finally, disconnect the parallel kit cables.

Entretien

The Pulsar PGiPAIRB4 Parallel Kit requires minimal maintenance. Follow these guidelines:

• Keep the unit clean and free of dirt, dust, and moisture.
• Inspect cables and connectors regularly for any signs of wear, damage, or corrosion. Replace if necessary.
• Store the kit in a dry, protected area when not in use.

Dépannage

Caractéristiques

• Modèle: PGiPAIRB4
• Volume de sortietage: 120/240V
• Fréquence de sortie : 60 Hz
• L14-50 Receptacle: 50 Amps
• L14-30 Receptacle: 30 Amps
• Générateurs compatibles : Pulsar PGDA70BiSCO, PGD95BiSCO, PGD105TiSCO
• Dimensions du produit : 12 x 9 x 4 pouces
• Poids de l'article : 3 livres
• Fabricant: Pulsar

Informations sur la garantie

For detailed warranty information regarding your Pulsar PGiPAIRB4 Parallel Kit, please refer to the warranty card included with your purchase or visit the official Pulsar Products webConsultez le site. Conservez votre preuve d'achat pour toute réclamation au titre de la garantie.

Assistance clientèle

If you have any questions, require technical assistance, or need to order replacement parts, please contact Pulsar Customer Support:

• Website: www.pulsarproducts.com
• Refer to your product registration or warranty documentation for specific contact numbers or email addresses.