1. Informations importantes sur la sécurité
Please read and understand all instructions before installing or operating this fixture. Failure to follow these instructions may result in electric shock, fire, or other hazards that could cause personal injury or property damage.
- AVERTISSEMENT: Risque de choc électrique. Coupez l'alimentation au niveau du fusible ou du disjoncteur avant toute installation ou intervention.
- AVERTISSEMENT: Risque d'incendie. Tenir les matériaux combustibles éloignés de la source d'incendie.amp.
- This fixture is intended for indoor use only. Do not use in wet locations or where directly exposed to water.
- Assurer le vol d'alimentationtage is compatible with the fixture's requirements (120V-277V).
- Tous les raccordements électriques doivent être effectués conformément aux normes électriques locales et nationales. En cas de doute, consultez un électricien qualifié.
- Ne tentez pas de modifier ou de démonter le dispositif. Il ne contient aucune pièce réparable par l'utilisateur.
2. Contenu de la boîte
Vérifiez que tous les composants sont présents avant de commencer l'installation :
- LED Shop Light Fixture(s)
- Matériel de montage (vis, chevilles)
- Linking Cables (1.5" and 8" for daisy-chaining)
- Écrous de fil
3. Spécifications
| Fonctionnalité | Spécification |
|---|---|
| Marque | Éclairage Sunco |
| Nom du modèle | LED Shop Light, 4ft Wraparound, Prismatic Lens, 8.5 Inch |
| Dimensions (L x l x H) | 48"L x 8.58"l x 2.56"H |
| Quoitage | 60 watts |
| Luminosité | 7200 lumens |
| Efficacité | 120 LM / W |
| Température de couleur (CCT) | Sélectionnable : 4000K, 5000K, 6000K |
| Voltage | 120V-277V |
| Gradable | Non (non dimmable) |
| Matériel | Alloy Steel, Polycarbonate |
| Type de montage | Ceiling Mount (Flush Mount) |
| Caractéristiques spéciales | Linkable, Wide Beam Angle (110°) |
| Certifications | ETL, FCC, RoHS |
| Durée de vie moyenne | 50,000 heures |
The fixture features a durable build with an impact-resistant prismatic lens for wide and consistent light dispersion.
This image illustrates key features including impact resistance, the prismatic lens design, non-dimmable functionality, and the wide voltage compatibility of 120-277V.
4. Configuration et installation
Follow these steps for proper installation. Ensure power is disconnected before starting.
4.1. Préparez l'installation
- Éteignez l'alimentation : Locate the circuit breaker controlling the installation area and turn off the power.
- Retirer le diffuseur : Gently remove the prismatic diffuser from the lamp base to access the internal components.
- Sélectionnez la température de couleur (CCT) : Before mounting, locate the CCT switch inside the fixture. Select your desired color temperature (4000K, 5000K, or 6000K). This setting cannot be changed easily after installation.
This image shows the internal CCT switch, allowing selection between 4000K, 5000K, and 6000K before installation.
4.2. Montage du luminaire
The fixture is designed for flush mounting to a ceiling or surface. It includes keyhole slots for easy installation.
- Marquer les points de montage : Hold the fixture in the desired mounting location and mark the positions for the mounting screws. Ensure these align with a junction box or suitable support structure.
- Installer le matériel de montage : Drill pilot holes if necessary and install the provided mounting screws, leaving a small gap for the fixture to slide onto.
- Préparation du câblage : If connecting to a junction box, knock out the appropriate punch hole on the fixture's housing.
This diagram illustrates the three main steps for installation: securing the housing, connecting electrical wires, and attaching the light fixture.
4.3. Connexion électrique
- Connecter les fils : Using the provided wire nuts, connect the fixture's wires to the supply wires: Live (black) to Live, Neutral (white) to Neutral, and Ground (yellow/green) to Ground. Ensure all connections are secure.
- Fils de repli : Carefully tuck all wires and wire nuts into the junction box or fixture housing.
4.4. Linking Multiple Fixtures (Daisy Chain)
This fixture supports daisy-chaining to extend lighting coverage. Use the provided linking cables.
- Connect Linking Cable: Insert one end of a linking cable into the designated port on the first fixture and the other end into the port on the next fixture.
- Connexions sécurisées : Ensure linking cables are securely connected and properly routed.
This image demonstrates how to daisy-chain multiple fixtures using the linking cables and highlights the knockout punch hole for electrical connections.
4.5. Dernières étapes
- Remettre le diffuseur en place : Align one end of the diffuser with the aluminum base and push it into place until it snaps securely.
- Restaurer l'alimentation : Turn the circuit breaker back on to restore power to the fixture.
5. Mode d'emploi
The Sunco Lighting LED Shop Light is designed for straightforward operation once installed.
5.1. Color Temperature Selection (CCT)
This fixture features a selectable color temperature (CCT) switch, allowing you to choose between 4000K (Cool White), 5000K (Daylight), and 6000K (Bright White) to suit your preference or application. The CCT switch is located inside the fixture and must be set during installation before the diffuser is reattached.
- 4000 K : Provides a neutral white light, suitable for offices or general workspaces.
- 5000 K : Offers a bright, crisp daylight-like illumination, ideal for tasks requiring high visibility.
- 6000 K : Delivers a very bright, cool white light, often preferred for industrial settings or areas needing maximum brightness.
This image displays the internal components and wiring, emphasizing the high efficiency of the LED fixture operating within a 120-277V range.
5.2. Marche/Arrêt
The fixture is non-dimmable and operates via a standard wall switch connected to its power supply. Simply toggle the wall switch to turn the light on or off.
6. Entretien
The Sunco Lighting LED Shop Light requires minimal maintenance. Always ensure power is disconnected before performing any maintenance.
- Nettoyage: Essuyez l'extérieur du luminaire avec un chiffon doux, sec ou légèrement humidifié.amp cloth. Do not use harsh chemicals or abrasive cleaners, as these can damage the finish or lens.
- Inspection: Periodically inspect the fixture for any signs of damage, loose wiring, or wear. If any issues are found, disconnect power and consult a qualified electrician.
- Aucun remplacement d'ampoule : This fixture uses integrated LEDs, meaning there are no bulbs to replace. The LEDs are designed for a long lifespan of 50,000 hours.
7. Dépannage
If you experience issues with your LED Shop Light, refer to the following common troubleshooting steps:
- La lumière ne s'allume pas :
- Vérifiez le disjoncteur pour vous assurer que le courant est allumé.
- Verify all wire connections are secure and correct.
- Assurez-vous que l'interrupteur mural est en position ON.
- La lumière vacille :
- Confirm the fixture is not connected to a dimmer switch, as it is non-dimmable.
- Vérifiez les connexions de câblage desserrées.
- Assurer le vol d'alimentationtage est stable et se situe dans la plage spécifiée.
- Température de couleur incorrecte :
- The CCT switch must be set before installation. If the diffuser is already installed, carefully remove it to access and adjust the switch.
If these steps do not resolve the issue, contact Sunco Lighting customer support for assistance.
8. Garantie et assistance
Sunco Lighting garantit la qualité de ses produits.
- Garantie: This product is backed by a 3-Year Warranty. Please refer to the official Sunco Lighting website or your purchase documentation for full warranty details and terms.
- Assistance clientèle : For technical assistance, troubleshooting, or warranty claims, please contact Sunco Lighting customer support.
