TIMESS Atomic Analog Wall Clock (Model TIMESS-M22) Instruction Manual

Introduction

Thank you for choosing the TIMESS Atomic Analog Wall Clock. This clock is designed for precise timekeeping, automatically synchronizing with the WWVB radio signal from the U.S. National Institute of Standards and Technology (NIST) in Fort Collins, Colorado. It features a large, easy-to-read analog dial and an integrated LCD display for additional information such as date, day, and temperature. This manual provides detailed instructions for setup, operation, and maintenance to ensure optimal performance.

Devant view of the TIMESS Atomic Analog Wall Clock, showing the blue dial, white numbers, and integrated LCD display.

Installation

1. Installation de la batterie

The clock operates on batteries. Locate the battery compartment on the back of the clock. This clock requires one AA carbon battery (not included) for the main clock mechanism and an additional AA alkaline battery (not included) for the LCD display. Ensure correct polarity when inserting batteries.

Arrière view of the clock, highlighting the battery compartment and control switches.

2. Sélection du fuseau horaire

On the back of the clock, locate the time zone switch (P/M/C/E). Slide the switch to select your correct time zone:

• PHeure du Pacifique
• MHeure des montagnes
• CHeure centrale
• EHeure de l'Est

3. Daylight Saving Time (DST) Switch

Locate the DST switch on the back of the clock. If your region observes Daylight Saving Time, slide the switch to the "ON" position during summer months. If your region does not observe DST, or during winter months, slide it to "OFF".

4. Réception du signal initial

After installing batteries and setting the time zone and DST, the clock will begin searching for the WWVB radio signal. The second hand will make one revolution and stop at the 12 o'clock position, then the minute/hour hands will move to the 12 o'clock position. This process can take 3 to 12 minutes. For a strong signal, the clock will set itself within 10 minutes. If the signal is weak or not received, the clock will search for the signal on the odd hours (1 AM, 3 AM, 5 AM, etc.) every 2 hours until a signal is acquired.

For best reception, place the clock near a window and away from electronic devices that may cause interference. Avoid placing it near large metal objects.

5. Montage

Once the time is set, you can hang the clock on a wall using the integrated hanging slot on the back. Ensure it is securely mounted.

Mode d'emploi

Réglage automatique de l'heure

The TIMESS Atomic Analog Wall Clock automatically receives the WWVB radio signal to ensure precise timekeeping. Once set up, you generally do not need to manually adjust the time, including for Daylight Saving Time changes (if the DST switch is correctly set).

Fonctions d'affichage à cristaux liquides

The integrated LCD display shows the month, date, day of the week, and temperature. You can switch between different display modes and temperature units.

• Switching between Time and Calendar Display: Use the "Down" button on the back of the clock to toggle the LCD display between showing the current time and the calendar (month, date, day).
• Switching between Fahrenheit (°F) and Celsius (°C): Use the "Up" button on the back of the clock to switch the temperature unit displayed on the LCD between Fahrenheit and Celsius.

Close-up of the LCD display, showing the month, date, day of the week, and temperature.

Entretien

• Remplacement de la batterie: Replace batteries annually or when the clock hands stop moving or the LCD display fades. Use a new AA carbon battery for the clock mechanism and a new AA alkaline battery for the LCD display.
• Nettoyage: Wipe the clock with a soft, dry cloth. Do not use abrasive cleaners or chemicals, as they may damage the finish or the glass panel.
• Placement: Avoid exposing the clock to extreme temperatures, direct sunlight, or high humidity, which can affect its accuracy and lifespan.

Dépannage

Clock Not Setting Automatically or Incorrect Time

• Vérifier la batterie: Ensure fresh batteries are installed with correct polarity.
• Réglage du fuseau horaire: Verify the time zone switch on the back of the clock is set to your correct region (P, M, C, or E).
• Paramètre d'heure d'été: Confirm the DST switch is in the appropriate ON/OFF position for your current season and region.
• Réception du signal: The clock needs to receive the WWVB signal. This can take 3-12 minutes initially, or longer in areas with weak signals. Try relocating the clock near a window, away from electronic interference (TVs, computers, microwaves) or large metal structures.
• Réinitialisation manuelle: If the clock still displays incorrect time after an extended period (e.g., 24 hours), press the "RESET" button on the back of the clock. This will force the clock to re-initiate the signal search.

LCD Display Not Working or Incorrect Date/Temperature

• Check LCD Battery: Ensure the separate AA alkaline battery for the LCD display is fresh and correctly installed.
• Manual Date/Time Setting for LCD: If the analog clock is correct but the LCD date/day is not, use the "SET", "UP", and "DOWN" buttons on the back of the clock to manually adjust the year, month, and day.
• Précision de la température: The temperature displayed is for the immediate vicinity of the clock. Ensure the clock is not in direct sunlight or near heat sources that could skew readings.

Pour obtenir de l'aide supplémentaire, veuillez consulter les informations de contact dans la section Garantie et assistance.

Caractéristiques

Vidéos pédagogiques

Garantie et assistance

For warranty information or technical support, please contact TIMESS customer service. Refer to your purchase documentation for specific warranty terms and contact details. You may also visit the TIMESS Store on Amazon pour obtenir des informations supplémentaires sur le produit et des ressources d'assistance.