1. Introduction
Thank you for choosing PAUTIX 5V USB COB LED Strip Lights. This manual provides essential information for the safe and efficient use of your LED strip lights. Please read these instructions carefully before installation and operation.
Contenu du colis :
- 1 x PAUTIX 5V USB COB LED Strip Light (6.56ft / 2m, 3000K Warm White)
- 1 x RF Wireless Remote Control
- 1 x USB Power Cable with In-line 3-button Dimmer
Image: Contents of the PAUTIX LED strip light package, showing the coiled strip, USB cable with in-line dimmer, and RF remote control.
2. Consignes de sécurité
- Homologué UL : This product is UL-Listed, ensuring compliance with safety standards.
- Vol faibletage: Operates on 5V DC, making it safe to touch for pets and children.
- Utilisation en intérieur uniquement : The LED strip has an IP30 rating and is designed exclusively for indoor environments. Avoid exposure to water or high humidity.
- Source d'alimentation : Use only with a 5V/2A (or higher) USB power source. Insufficient power may cause flickering or improper operation.
- Installation: Pour une performance adhésive optimale, assurez-vous que la surface de montage soit propre, sèche et lisse.
- Coupe: The strip can be cut at designated marks (every 12mm/0.47in). Cutting at non-marked points will damage the circuit.
- Chaleur: While COB LEDs produce minimal heat, ensure proper ventilation when installed in enclosed spaces.
3. Configuration et installation
- Préparez la surface : Clean the desired mounting surface thoroughly to remove dust, oil, or moisture. A clean, dry, and smooth surface ensures strong adhesion.
- Mesurer et couper (facultatif) : If a shorter length is required, measure the desired length and cut the LED strip only at the designated cutting marks (indicated by copper pads).
Image: Diagram showing the cuttable sections of the LED strip, marked every 12mm/0.47in, with a pair of scissors indicating where to cut.
- Support adhésif pelable : Carefully peel off the protective film from the 3M self-adhesive backing on the LED strip.
- Fixez la bande : Press the LED strip firmly onto the prepared surface, ensuring even contact along its entire length.
Image: Four-step visual guide demonstrating how to install the LED strip: clean the surface, peel the backing, paste the strip, and turn on the light.
- Connecter l'alimentation : Plug the USB connector of the LED strip into a compatible 5V/2A (or higher) USB power source (e.g., TV USB port, computer, power bank, USB wall adapter).
Image: Various USB power sources compatible with the PAUTIX LED strip, including a USB charger, power bank, laptop/TV, 5V battery pack, and USB socket.
4. Mode d'emploi
RF Wireless Remote Control:
The included RF remote control allows for convenient operation from a distance, even without direct line of sight (360° control). It features:
- Marche/Arrêt : Allumer ou éteindre les lumières.
- Réglage de la luminosité : Increase or decrease brightness (5 levels).
- Fonctions de la minuterie : Set the lights to turn off automatically after 30 minutes, 1 hour, 2 hours, 3 hours, or 4 hours. Press 'C' to cancel the timer.
- Fonction mémoire : The lights will restore to their last brightness setting when turned back on.
Image: The PAUTIX LED strip light coiled with the RF wireless remote control and USB power cable visible. The remote shows buttons for power, brightness, and timer settings.
Image: A child sleeping with the LED strip lights providing soft illumination, illustrating the timer function of the RF remote control.
In-line 3-button Dimmer:
The USB power cable includes an in-line controller with three buttons for basic operation:
- Bouton d'alimentation : Turns the lights on/off.
- Brightness Up (+): Augmente la luminosité.
- Brightness Down (-): Diminue la luminosité.
Image: A living room scene with LED strip lights installed, showing the in-line dimmer and its buttons for adjusting brightness from 10% to 100%.
5. Entretien
- Nettoyage: Gently wipe the LED strip with a dry, soft cloth if it accumulates dust. Do not use liquid cleaners or immerse in water.
- Adhésif: The 3M adhesive is strong. If repositioning is necessary, do so carefully to avoid damaging the strip or the surface.
- Stockage: Lorsqu'elle n'est pas utilisée pendant une période prolongée, rangez la bande LED dans un endroit frais et sec, à l'abri de la lumière directe du soleil.
6. Dépannage
| Problème | Cause possible | Solution |
|---|---|---|
| Les lumières ne s'allument pas. | Pas d'alimentation, connexion défectueuse, port USB défectueux. |
|
| Les lumières clignotent. | Alimentation électrique insuffisante. |
|
| La télécommande ne fonctionne pas. | Battery issue, interference. |
|
| Sections of the strip are not lighting up. | Dommages à la bande. |
|
7. Spécifications
- Modèle: RF-SWW320COB-USB-2M-3000K-NEW
- Marque: PAUTIX
- Type de source lumineuse : LED COB
- Température de couleur: Blanc chaud 3000K
- Longueur: 6.56 pieds (2 mètres)
- LEDs per Meter: 320 LEDs/m (Total 640 LEDs)
- Voltage: 5 volts (CC)
- Quoitage: 9.5 watts
- Flux lumineux : 1200 lumens
- Indice de rendu des couleurs (IRC) : >90
- Caractéristiques spéciales : 5V USB Powered, RF Remote Control, UL-Listed, Dimmable, Dotless, Flicker-Free, Memory Function, Timer
- Durée de vie: >65,000 XNUMX heures
- Indice de protection IP (Indice de protection IP) : IP30 (utilisation en intérieur uniquement)
- Matériel: 3M Adhesive, COB LED Light Source, Double Layer Pure Copper PCB, Plastic
- Longueur du câble d'alimentation : 2.6 pieds
- Code à barres : 717994811924
8. Garantie et assistance
PAUTIX is committed to customer satisfaction. This product comes with a Garantie de 5 ans, garantissant qualité et fiabilité.
If you encounter any issues or have questions regarding your PAUTIX LED Strip Lights, please contact our customer support team. We aim to respond within 24 hours and provide a prompt resolution.
Coordonnées: Please refer to the product packaging or the official PAUTIX website pour obtenir les coordonnées les plus récentes du service client.
