1. Introduction
This manual provides essential information for the proper installation, use, and maintenance of your Mopar 68525329AC Semi-Metallic Front Disc Brake Pads. These brake pads are designed to deliver reliable stopping power and durability for compatible vehicles.
2. Consignes de sécurité
AVERTISSEMENT:
- Brake system work should only be performed by qualified personnel. Improper installation can lead to brake failure and serious injury or death.
- Always wear appropriate personal protective equipment (PPE), including safety glasses and gloves, when working on vehicle brake systems.
- Brake dust may contain hazardous materials. Avoid inhaling dust and use proper disposal methods.
- Avant toute intervention, assurez-vous que le véhicule est correctement calé sur des chandelles. Ne vous fiez jamais uniquement au cric.
- Veuillez vous référer au manuel d'entretien de votre véhicule pour connaître les spécifications de couple et les procédures spécifiques.
3. Contenu du colis
Avant de commencer l'installation, vérifiez que tous les composants sont présents et non endommagés.
- 2 x Mopar 68525329AC Semi-Metallic Front Disc Brake Pads (set for one axle)
- Brake hardware kit (shims, clips, etc., as applicable)
Figure 1: Contents of the Mopar 68525329AC Brake Pad Kit, showing the brake pads, associated hardware, and the Mopar branded packaging.
4. Installation (Configuration)
This section outlines the general procedure for replacing front disc brake pads. Always consult your vehicle's specific service manual for detailed instructions and torque specifications.
- Préparez le véhicule : Park the vehicle on a level surface, engage the parking brake, and block the rear wheels. Loosen the front wheel lug nuts.
- Soulever et sécuriser : Safely lift the front of the vehicle using a jack and support it securely with jack stands. Remove the front wheels.
- Access Caliper: Locate the brake caliper. Depending on your vehicle, you may need to remove two caliper guide pins or bolts to swing the caliper open or remove it entirely.
- Supprimer les anciens tampons : Carefully slide out the old brake pads from the caliper bracket. Note their orientation.
- Nettoyer et inspecter : Clean the caliper, caliper bracket, and rotor surface thoroughly. Inspect the brake rotor for excessive wear, scoring, or cracks. Replace if necessary. Inspect caliper guide pins and boots for damage.
- Piston de compression : Use a brake caliper piston compression tool to slowly and evenly push the caliper piston(s) back into the caliper bore. This creates space for the new, thicker pads.
- Installer du nouveau matériel : Install any new shims, clips, or anti-rattle springs provided in the hardware kit onto the new brake pads or caliper bracket as per your vehicle's manual.
- Installer de nouveaux coussinets : Carefully slide the new Mopar brake pads into the caliper bracket, ensuring they are correctly seated and oriented.
- Réassemblez l'étrier : Reinstall the brake caliper over the new pads and rotor. Secure the caliper guide pins or bolts, tightening them to the manufacturer's specified torque.
- Purger les freins (si nécessaire) : If the brake lines were opened or air entered the system, bleed the brake system according to your vehicle's service manual.
- Réinstaller les roues : Reinstall the wheels and hand-tighten the lug nuts.
- Véhicule inférieur : Safely lower the vehicle to the ground.
- Couple final : Torque the lug nuts to the vehicle manufacturer's specifications in a star pattern.
- Pédale de frein à pompe : Before driving, slowly pump the brake pedal several times until a firm pedal feel is achieved. This seats the pads against the rotor and restores hydraulic pressure. Check the brake fluid reservoir level.
5. Bedding-In Procedure (Operating)
Proper bedding-in is crucial for optimal brake performance and longevity. This process transfers a thin, even layer of friction material from the pads to the rotor surface.
- Trouvez un endroit sûr et dégagé, peu fréquenté.
- Perform 10-15 moderate stops from approximately 30-40 mph (50-65 km/h) down to about 5-10 mph (8-16 km/h). Do not come to a complete stop.
- Prévoyez environ 30 secondes entre chaque arrêt pour permettre aux freins de refroidir légèrement.
- After the last stop, drive for several minutes without using the brakes to allow them to cool completely. Avoid hard braking during this cool-down period.
- During the bedding-in process, you may notice some smoke or a burning smell. This is normal.
IMPORTANT:
Avoid heavy braking, panic stops, or prolonged braking (e.g., down a long hill) for the first 200-300 miles (320-480 km) after installation to allow the pads to fully seat.
6. Entretien
- Inspection régulière : Inspect brake pads, rotors, and fluid levels regularly as part of your vehicle's recommended maintenance schedule.
- Usure des coussinets : Replace brake pads when the friction material wears down to the minimum thickness specified by your vehicle manufacturer, typically around 2-3mm.
- Liquide de frein : Ensure brake fluid is at the proper level and is clean. Consult your vehicle manual for brake fluid replacement intervals.
- État du rotor : Check rotors for warping, deep grooves, or cracks. Replace or resurface rotors as needed when replacing pads.
7. Dépannage des problèmes courants
| Symptôme | Cause possible | Solution |
|---|---|---|
| Bruit de grincement/grincement | New pads not bedded-in, worn pads, foreign object, improper installation, worn rotors. | Perform bedding-in procedure. Inspect pads for wear. Check for debris. Re-install correctly. Inspect/replace rotors. |
| Vibration/Pulsation during braking | Warped rotors, uneven pad transfer, caliper issues. | Inspect/replace rotors. Re-bed pads. Check caliper for sticking. |
| Pédale de frein molle ou spongieuse | Présence d'air dans les conduites de frein, niveau de liquide de frein bas, problème de maître-cylindre. | Bleed brake system. Check fluid level and leaks. Consult a mechanic for master cylinder issues. |
8. Spécifications
- Marque: Mopar
- Numéro de modèle : 68525329AC
- Matériel: Semi-Metallic
- Position de la pièce automobile : Devant
- Spécification respectée : Fabricant d'équipement d'origine
- Fabricant: Stellantis
- Nombre d'articles : 2 (per kit)
9. Informations sur la garantie
Mopar parts are backed by a limited warranty. For specific warranty terms and conditions, please refer to the official Mopar warranty documentation provided with your purchase or visit the official Mopar webConsultez le site. Conservez votre preuve d'achat pour toute réclamation au titre de la garantie.
10. Assistance clientèle
For technical assistance, installation questions, or warranty inquiries, please contact your authorized Mopar dealer or visit the official Mopar support webVous trouverez plus d'informations et les coordonnées sur le site. Mopar Store on Amazon.
