Introduction
This manual provides essential information for the safe and effective installation, operation, and maintenance of your MALIIGAZA 32.8FT COB LED Strip Light. Please read these instructions carefully before use and retain them for future reference.
The MALIIGAZA COB LED Strip Light is a flexible, high-brightness lighting solution featuring Chip-on-Board (COB) technology. It delivers uniform, dotless illumination with a high Color Rendering Index (CRI) of 90+, ensuring accurate color representation. This 24V strip is dimmable and designed for various indoor decorative lighting applications.
Image: Flexible COB LED Strip with key features.
Consignes de sécurité
- Exigence d'alimentation : This LED strip operates on 24V DC. DO NOT connect the LED strip directly to AC 110V or 220V (standard wall power socket). An appropriate AC/DC transformer (power supply) is required and is NOT included with this product. Connecting directly to AC power will damage the strip and poses a safety risk.
- Utilisation en intérieur uniquement : This product is designed for indoor applications. Avoid exposure to moisture, water, or outdoor elements unless explicitly stated otherwise for a specific variant.
- VoltagCompatibilité : Ensure your power supply and any controllers are compatible with the 24V DC requirement of this LED strip.
- Installation by Qualified Personnel: En cas de doute concernant le câblage électrique, consultez un électricien qualifié.
- Évitez la surchauffe : Do not install the LED strip in enclosed spaces without adequate ventilation. Ensure proper heat dissipation to prolong the lifespan of the product.
- Cutting Precautions: Only cut the LED strip at designated cutting marks. Cutting elsewhere may damage the circuit and render sections of the strip inoperable.
Qu'y a-t-il dans la boîte
Votre forfait comprend :
- 1 x 32.8FT COB LED Strip Light
Note: Power supply/adapter and controller are NOT included and must be purchased separately.
Caractéristiques
| Marque | MALIIGAZA |
| Numéro de modèle | MALIIGAZA COB LED STRIP |
| Longueur | 32.8 pieds (10 mètres) |
| Voltage | 24 volts (CC) |
| Température de couleur | 4000K (blanc naturel) |
| Indice de rendu des couleurs (IRC) | RA90+ |
| LED par mètre | 384 LED/mètre |
| Largeur du PCB | 8 mm |
| Quoitage | 50 watts |
| Flux lumineux | 8000 lumens |
| Durée de vie | 50,000+ heures |
| Matériel | Caoutchouc de silicone |
| Utilisation intérieure/extérieure | Intérieur |
| Dossier spécial | Dotless lighting, Dimmable |
Image: High Color Rendering Index (CRI) Ra90+ for authentic color restoration.
Configuration et installation
Follow these steps for proper installation of your COB LED strip light:
- Préparez la surface : Ensure the installation surface is clean, dry, and smooth. Remove any dust, oil, or moisture that could affect the adhesive.
- Mesurer et couper (facultatif) : The LED strip is flexible and can be cut to your desired length. Locate the designated cutting marks (approximately every 1.22 inches or 31mm) along the strip. Use sharp scissors to cut precisely at these marks. Do not cut in other areas.
Image: Features of the LED strip including cut points and adhesive.
- Appliquer la bandelette : Peel off the backing from the strong double-sided adhesive tape on the back of the LED strip. Carefully press the strip onto the prepared surface, ensuring firm contact along its entire length.
- Connect Power Supply and Controller: The LED strip requires a 24V DC power supply (transformer) and optionally a controller for dimming or other functions. Connect the LED strip to the controller (if used), and then connect the controller to the 24V DC power supply. Finally, plug the power supply into a standard wall outlet.
Image: LED light strip installation diagram showing correct and incorrect power connections.
Important: Ensure all connections are secure and polarity is correct (positive to positive, negative to negative). Refer to the diagram for proper wiring. Never connect the LED strip directly to 110V/220V AC power.
Mode d'emploi
Once installed and connected to a compatible 24V DC power supply and controller (if applicable), your MALIIGAZA COB LED Strip Light is ready for operation.
- Marche/Arrêt : Use the switch on your power supply or controller to turn the LED strip on or off.
- Brightness Adjustment (Dimmable): If using a dimmable power supply or controller, adjust the brightness level according to your preference. The COB LED strip supports smooth dimming from 100% down to low levels.
Image: Brightness adjustment levels from 100% to 20%.
- Application: The uniform and soft lighting is ideal for various indoor settings such as kitchen under-cabinet lighting, bedroom accent lighting, ceiling coves, stair lighting, mirror backlighting, and more.
Image : Examples of wide application for the LED strip lights.
Entretien
The MALIIGAZA COB LED Strip Light requires minimal maintenance to ensure its longevity and performance.
- Nettoyage: Gently wipe the surface of the LED strip with a soft, dry cloth to remove dust. For stubborn dirt, a slightly damp cloth can be used, but ensure the strip is completely dry before reconnecting power. Do not use harsh chemicals or abrasive cleaners.
- Inspection: Periodically check the strip for any signs of damage, such as cuts, cracks, or loose connections. Address any issues promptly to prevent further damage or safety hazards.
- Évitez le stress physique : While flexible, avoid excessive bending, twisting, or pulling of the LED strip, especially at connection points, to prevent internal damage.
Dépannage
If you encounter issues with your MALIIGAZA COB LED Strip Light, refer to the following common problems and solutions:
| Problème | Cause possible | Solution |
|---|---|---|
| La bande LED ne s'allume pas | No power, incorrect connection, faulty power supply/controller, damaged strip. | Check if the power supply is plugged in and receiving power. Verify all connections (strip to controller, controller to power supply) are secure and correct polarity. Test the power supply with another device if possible. Inspect the strip for visible damage. |
| Les lumières sont faibles ou vacillantes | Insufficient power, loose connection, faulty dimmer/controller, voltage goutte. | Assurer l'alimentation électriquetage is sufficient for the strip's length. Check all connections for looseness. If using a dimmer, ensure it is compatible and functioning correctly. While this strip is designed for minimal voltage drop over 32.8ft, ensure the power supply is adequately rated. |
| Seule une partie de la bande s'allume | Damage to a section, incorrect cutting. | Inspect the unlit section for physical damage or improper cuts. If a section was cut incorrectly, it may be permanently damaged. |
| L'adhésif ne tient pas | Surface not clean/dry, improper application, unsuitable surface material. | Ensure the surface is thoroughly cleaned and dried before application. Apply firm pressure along the strip during installation. For rough or porous surfaces, consider using additional mounting clips or stronger adhesive. |
Garantie et assistance
MALIIGAZA products are manufactured to high-quality standards. For specific warranty details, please refer to the product packaging or the retailer's website where the product was purchased. In most cases, a standard manufacturer's warranty covers defects in materials and workmanship under normal use.
If you experience any issues or have questions regarding your MALIIGAZA COB LED Strip Light, please contact MALIIGAZA customer support through the retailer's platform or the official MALIIGAZA website. Please have your purchase information and product model number ready when contacting support.
