Introduction
Le Wampler Catacombs is a programmable, all-in-one delay and reverb pedal designed to provide a wide range of time-based effects for musicians. This manual provides essential information for setting up, operating, maintaining, and troubleshooting your Catacombs pedal.
Produit terminéview
The Catacombs pedal integrates 11 popular delay and reverb sounds into a single, intuitive unit. It features studio-quality 48 kHz sampling rate with 24-bit audio conversion, 8 onboard preset locations, and MIDI compatibility for up to 128 total presets.
Figure 1 : Devant view du Wampler Catacombs pedal, showing controls for delay and reverb effects, input/output jacks, and footswitches.
Figure 2 : Incliné view du Wampler Catacombs pedal, highlighting its compact design and various control knobs.
Installation
Exigences en matière d'alimentation
Le Wampler Catacombs pedal requires a standard 9V DC power supply (not included) with a center-negative barrel connector. Ensure the power supply provides sufficient current for optimal performance.
Branchement de votre pédale
- Connectez votre instrument (par exemple, une guitare) au ENTRÉE MONO or ENTRÉE STÉRÉO Prise jack sur le côté droit de la pédale utilisant un câble d'instrument standard de 6,35 mm (1/4 pouce).
- Connectez le SORTIE MONO or STEREO OUT La prise jack située à gauche de la pédale vers votre ampAmplificateur ou pédale d'effet suivante.
- Connect the 9V DC power supply to the 9 V CC prise d'entrée.
- For MIDI control, connect a MIDI cable to the MIDI saisir.
Mode d'emploi
Contrôles surview
- Delay Type Knob: Selects between various delay types including Tape, SPC, FTE, BBD, ANLG, and DIGI.
- Reverb Type Knob: Selects between reverb types such as SHMR (Shimmer), PLT (Plate), SPR (Spring), ROOM, and HALL.
- Time/Shimmer Knob: Adjusts the delay time or shimmer intensity depending on the selected effect.
- Feedback/Decay Knob: Controls the number of delay repeats or the reverb decay time.
- Mod Rate Knob: Adjusts the modulation rate for effects with modulation.
- Delay Tone Knob: Shapes the tone of the delay repeats.
- Reverb Tone Knob: Shapes the tone of the reverb effect.
- Bypass/ALT Footswitch: Toggles the effect on/off. Hold to access alternate functions (ALT mode).
- Preset/Save Footswitch: Cycles through presets. Hold to save current settings to a preset location.
- Tap Tempo Footswitch: Taps in the desired delay tempo.
Enregistrement et rappel des préréglages
The Catacombs pedal allows for 8 onboard preset locations. To save a preset, adjust the knobs to your desired sound, then press and hold the Preset/Save footswitch until the indicator lights confirm the save. To recall a preset, short press the Preset/Save footswitch to cycle through the saved locations.
Alternate Functions (ALT Mode)
Some knobs have alternate functions accessible by holding the Bypass/ALT footswitch. When in ALT mode, the indicator light will change (e.g., from blue to red as noted in some user feedback), allowing you to adjust secondary parameters. Release the footswitch to return to normal operation.
Entretien
To ensure the longevity and optimal performance of your Wampler Catacombs pedal, follow these maintenance guidelines:
- Nettoyez la pédale avec un chiffon doux et sec. Évitez les nettoyants abrasifs et les solvants.
- Rangez la pédale dans un endroit frais et sec, à l'abri de la lumière directe du soleil et des températures extrêmes.
- Coupez l'alimentation électrique lorsque l'appareil n'est pas utilisé pendant une période prolongée.
- Regularly check all cable connections for secure fit.
Dépannage
| Problème | Cause possible | Solution |
|---|---|---|
| Aucun son lorsque la pédale est actionnée. | Incorrect power supply, faulty cables, incorrect input/output connections. | Verify power supply is 9V DC center-negative. Check all instrument cables. Ensure input is connected to IN and output to OUT. |
| Effect is too subtle or too extreme. | Knobs are set incorrectly, or in ALT mode unintentionally. | Adjust the relevant control knobs (Time, Feedback, Tone). Check if the pedal is in ALT mode and adjust accordingly. |
| Impossible d'enregistrer ou de rappeler les préréglages. | Fonctionnement incorrect de la pédale. | Ensure you are holding the Preset/Save footswitch long enough to save. For recalling, use short presses. |
| Bruit ou bourdonnement. | Ground loop, faulty power supply, interference. | Use an isolated power supply. Try different cables. Ensure proper grounding of all equipment. |
Caractéristiques
- Modèle: CATACOMBS
- Dimensions: 7.25 x 5.7 x 3.75 pouces
- Poids de l'article : 1.39 livres
- Source d'alimentation : Corded Electric (9V DC, center-negative, power supply not included)
- Format des signaux : Analogique
- Effets de sortie audio : Délai, réverbération
- SampTaux de ling: 48 kHz
- Audio Bit Depth: 24 bits
- Présélections: 8 onboard, 128 via MIDI
- Manufacture Location: Designed and Built in the USA
Garantie et assistance
Wampler Pedals products are designed and built to high standards. For warranty information and technical support, please refer to the official Wamppédales webConsultez leur site web ou contactez directement leur service client. Conservez votre preuve d'achat pour toute réclamation au titre de la garantie.
Pour obtenir de l'aide supplémentaire, visitez le Wampler Store on Amazon.
