1. Consignes de sécurité
Read and understand all instructions before beginning installation. Failure to follow these instructions may result in electric shock, fire, property damage, or personal injury.
- Coupez toujours l'alimentation au niveau du tableau électrique avant de câbler ou d'entretenir l'appareil.
- Tous les câblages doivent être conformes aux codes et normes électriques locaux.
- Cet appareil est conçu uniquement pour la ventilation générale. Ne pas utiliser pour l'évacuation de matières ou de vapeurs dangereuses ou explosives.
- To reduce the risk of fire or electric shock, do not use this fan with any solid-state speed control device unless specifically approved for such use.
- Ensure the installation location provides adequate structural support for the fan.
2. Contenu du colis
Vérifiez que tous les composants sont présents avant de commencer l'installation :
- Boîtier de ventilateur
- Assemblage de la calandre
- LED Bulbs (2x)
- Frosted Glass Cover
- Vis de montage
- Manuel d'instructions
Image: Components of the Akicon Bathroom Exhaust Fan.
Video: Unboxing guide for the Akicon Bath Fan 1480 Satin White, showing all included parts.
3. Spécifications du produit
| Fonctionnalité | Spécification |
|---|---|
| Marque | Akicon |
| Nom du modèle | BPT14-80CL |
| Capacité de débit d'air | 80 pieds cubes par minute (CFM) |
| Niveau de bruit | 2.0 sons |
| Source d'énergie | AC |
| Voltage | 120 volts |
| Quoitage | 27.6 watts |
| Dimensions du produit | 13"P x 13"L x 7.75"H |
| Dimensions du boîtier | 8-1/2" x 8-1/2" x 5-3/4" |
| Diamètre du couvercle lumineux | 13" |
| Taille du conduit | 4 pouces |
| Dossier spécial | LED Light (3000K, 4000K, 5000K selectable, Dimmable) |
| Certifications | cUL, HVI Listed |
Image: Key dimensions of the Akicon Bathroom Exhaust Fan.
Image: Detailed housing dimensions and ceiling opening size requirements.
4. Installation
This fan can be installed with or without attic access. Refer to the appropriate video and steps below.
4.1 Vérifications avant l'installation
- Ensure your soffit or attic has enough space for installation.
- Required opening size: 8-1/2" x 8-5/16".
- Soffit/Attic Height: > 6-1/2".
Image: Pre-installation considerations for attic and soffit space.
4.2 Installation with Attic Access
- Starting next to a joist, trace an outline for the fan housing.
- Use a drywall saw to cut the marked opening.
- Slide the fan housing into the opening and screw it into the joist.
- Attach the duct to the fan's exhaust port and apply HVAC tape over the connection to ensure a secure seal.
- Connect the house wires to the fan wires (black to black, white to white, ground to ground).
- Place insulation over and around the fan housing.
- Plug in the light connection.
- Install the grille, LED bulbs, and glass cover.
Video: Step-by-step installation guide for the Akicon 1480 series Bathroom fan with attic access.
4.3 Installation without Attic Access (No-Attic Installation)
- If attic access is not available, this model allows for no-attic installation.
- First, disconnect the wires connecting the motor and the housing.
- Remove the fixing screws on the outside of the housing. This allows you to remove the motor from the housing.
- After connecting the ventilation duct, send the housing into the ceiling opening.
- Connect the wires correctly according to the label on the wires (black to black, white to white, ground to ground).
- Secure the housing to the joist using appropriate fasteners.
- Reinstall the motor back into the housing and connect the plugs.
- Finally, install the grille, LED bulbs, and glass cover.
Video: Detailed instructions on how to install the bathroom exhaust fan light combo without attic access.
4.4 Schéma de câblage
Image: Electrical wiring diagram for connecting the fan and light to a switch.
5. Mode d'emploi
The Akicon BPT14-80CL fan is designed for efficient and quiet operation.
5.1 Fonctionnement du ventilateur
- The fan operates at 80 CFM (Cubic Feet Per Minute) with a noise level of 2.0 Sones, ensuring effective ventilation with minimal sound.
- Activate the fan using the connected wall switch.
Fonctionnement de la lumière LED 5.2
- The integrated LED light offers three color temperature options: 3000K (Warm White), 4000K (Cool White), and 5000K (Daylight).
- To select your desired color temperature, locate the sliding switch on the back of the lampshade (or on the LED bulbs themselves, depending on the specific bulb type). Adjust this switch before installing the glass cover.
- The LED light is dimmable, allowing you to adjust brightness using a compatible dimmer switch (sold separately).
Image : Terminéview of the fan's performance and lighting features.
Video: Demonstration of the Akicon Bathroom Exhaust Fan with Light (AK1480-SW) features, including CCT selection and dimming.
6. Entretien
Un entretien régulier garantit des performances optimales et une longue durée de vie à votre ventilateur d'extraction.
6.1 Cleaning the Grille and Glass Cover
- Disconnect power at the service panel before cleaning.
- Carefully remove the glass cover by rotating it counter-clockwise.
- Wash the glass cover with mild soap and water, then dry thoroughly.
- Essuyez la grille avec l'adamp chiffon. N'utilisez pas de nettoyants abrasifs.
- Reinstall the glass cover by aligning the markings and rotating clockwise until secure.
6.2 Remplacement des ampoules LED
- Coupez l'alimentation au niveau du panneau de service.
- Remove the glass cover as described above.
- Unscrew the old LED bulbs and replace them with new ones of the same type (GU24 base, if applicable, or compatible LED bulbs).
- Reinstall the glass cover.
7. Dépannage
If your fan is not operating correctly, consult the following common issues:
| Problème | Cause possible | Solution |
|---|---|---|
| Le ventilateur ne fonctionne pas | Pas de courant, câblage desserré, interrupteur défectueux | Check circuit breaker, verify wiring connections, test switch. |
| La lumière ne s'allume pas | Loose bulb, faulty bulb, wiring issue | Ensure bulbs are screwed in tightly, replace bulbs, check light wiring. |
| Bruit excessif | Loose mounting, debris in fan, motor issue | Check mounting screws, clean fan blades, contact support if motor is faulty. |
| Mauvaise ventilation | Blocked duct, fan too small for room, dirty fan blades | Check duct for obstructions, ensure fan size is appropriate for room area, clean fan blades. |
8. Garantie et assistance
This Akicon Bathroom Exhaust Fan comes with a 3-Year Limited Warranty, ensuring confidence in the quality and construction of the product.
8.1 Assistance clientèle
Pour toute question, problème ou pièce manquante, veuillez contacter le service client d'Akicon :
- Heures de service: 8 h – 6 h HNE, du lundi au vendredi
- Téléphone: +1 (302) 213-4406
- E-mail: service@akiconshop.com
