1. Introduction
This manual provides essential information for the proper installation, use, and maintenance of the Graphtec Authentic CE7000 Series Teflon Cutting Strip Replacement (CE7000-130). This product is an authentic Graphtec part designed specifically for use with Graphtec CE7000 Series cutting plotters.
The cutting strip is a critical component that protects the plotter's cutting blade and ensures precise, clean cuts by providing a smooth, sacrificial surface for the blade to press against. Regular replacement of this strip is vital for maintaining optimal performance and extending the life of your cutting blades.
2. Consignes de sécurité
Please read and understand all safety precautions before handling or installing the cutting strip. Failure to follow these instructions may result in injury or damage to your equipment.
- Always power off and unplug your Graphtec cutting plotter before performing any maintenance or part replacement.
- Exercise caution when handling cutting blades. They are extremely sharp.
- Gardez la zone de travail propre et bien éclairée.
- Dispose of old cutting strips and any waste materials responsibly.
- Ce produit n'est pas un jouet. Tenir hors de portée des enfants.
3. Produit terminéview
The Graphtec Authentic CE7000 Series Teflon Cutting Strip is designed for durability and precision. Each package contains two (2) replacement strips.
Figure 3.1: Graphtec CE7000 Series Teflon Cutting Strip (2-pack) and packaging.
Figure 3.2 : Gros plan view of the Graphtec Teflon Cutting Strip, highlighting its flexible nature and the adhesive backing.
Each strip features a single side with an aggressive adhesive for secure attachment to your plotter, and an opposite side with a rigid Teflon base that provides the ideal cutting surface. The strip has a width of 10mm and a length of 50 inches, specifically sized for the CE7000-130 model.
Important Note: This cutting strip is exclusively compatible with Graphtec CE7000 Series cutting plotters. It is NOT compatible with CE5000 or CE6000 Series models.
4. Installation (Configuration)
Follow these steps carefully to replace the Teflon cutting strip on your Graphtec CE7000 Series plotter:
- Prepare the Plotter: Ensure your Graphtec CE7000 Series plotter is powered off and unplugged from the electrical outlet. Open the cover to access the cutting area.
- Remove the Old Strip: Carefully peel off the old, worn cutting strip from the plotter's cutting channel. If the adhesive is stubborn, you may gently warm it with a hairdryer on a low setting to soften it, but avoid excessive heat.
- Nettoyer la surface : Thoroughly clean the cutting channel where the strip was located. Use isopropyl alcohol and a lint-free cloth to remove any adhesive residue, dust, or debris. The surface must be completely clean and dry for the new strip to adhere properly.
- Position the New Strip: Unroll the new Graphtec Teflon cutting strip. Locate the cutting channel on your plotter. The strip should be aligned precisely within this channel.
Figure 4.1: Proper placement of the Teflon cutting strip within the plotter's cutting channel.
- Apply the New Strip: Starting from one end, carefully peel back a small section of the adhesive backing from the new strip. Align the strip perfectly with the cutting channel and press it down firmly. Slowly continue to peel the backing while pressing the strip down along the entire length of the channel, ensuring no air bubbles or wrinkles. Apply firm, even pressure.
- Sécuriser la bande : Once the strip is fully applied, run your finger or a soft, flat tool along its entire length to ensure maximum adhesion and to remove any trapped air.
- Vérifier l'installation : Close the plotter cover and reconnect the power. Perform a test cut to ensure the new strip is functioning correctly and providing optimal cutting performance.
5. Fonctionnement et fonction
The Teflon cutting strip is a passive but essential component of your Graphtec CE7000 Series plotter. Its primary function is to provide a smooth, consistent, and durable surface for the cutting blade to press against during operation. This ensures:
- Protection de la lame : Prevents the cutting blade from directly contacting the metal components of the plotter, which would dull the blade quickly.
- Découpes précises : A uniform cutting surface allows the blade to maintain consistent depth and pressure, resulting in clean, accurate cuts on various materials.
- Reduced Friction: The Teflon material minimizes friction, allowing the blade to glide smoothly across the surface.
No specific operational steps are required for the cutting strip itself once installed. Its function is integrated into the normal operation of your Graphtec cutting plotter.
6. Entretien
Regular inspection of your Graphtec Teflon cutting strip is crucial for maintaining cutting quality and extending blade life. While the strip itself requires minimal maintenance, its condition directly impacts your plotter's performance.
- Inspection visuelle : Periodically inspect the cutting strip for signs of wear, such as grooves, indentations, deep cuts, or peeling. These are indicators that the strip is nearing the end of its useful life.
- Nettoyage: If debris or adhesive residue accumulates on the strip, gently wipe it with a lint-free cloth dampened with isopropyl alcohol. Ensure the strip is completely dry before resuming operation.
- Calendrier de remplacement : The lifespan of a cutting strip varies depending on usage frequency and material types cut. Replace the strip immediately if you notice a decline in cutting quality, blade damage, or visible wear. It is good practice to have a spare strip on hand.
7. Dépannage
Issues related to the cutting strip often manifest as problems with cutting quality or blade performance. Refer to the table below for common issues and their solutions:
| Problème | Cause possible | Solution |
|---|---|---|
| Poor cutting quality (ragged edges, incomplete cuts) | Worn or damaged cutting strip; improper blade depth. | Inspect the cutting strip for wear. Replace if necessary. Adjust blade depth according to your plotter's manual. |
| Blade dulls quickly | Severely worn cutting strip allowing blade to hit metal; incorrect blade pressure. | Replace the cutting strip. Ensure proper blade pressure settings. |
| Cutting strip peeling or bubbling | Improper installation (surface not clean); adhesive failure. | Remove the old strip, thoroughly clean the surface, and install a new strip carefully, ensuring firm adhesion. |
| Strip not adhering properly | Surface not clean or dry; insufficient pressure during installation. | Ensure the cutting channel is free of all debris and completely dry before applying the new strip. Apply firm, even pressure during installation. |
If problems persist after troubleshooting, refer to your Graphtec CE7000 Series plotter's main user manual or contact Graphtec technical support.
8. Spécifications
- Nom du produit: Graphtec Authentic CE7000 Series Teflon Cutting Strip Replacement
- Modèle: CE7000-130
- Numéro de pièce : PM-CR-011
- Compatibilité: Graphtec CE7000 Series Cutting Plotters ONLY (Not compatible with CE5000 or CE6000 Series)
- Dimensions: 50 inches (Length) x 10mm (Width)
- Matériel: Teflon with aggressive adhesive backing
- Quantité: 2 strips per pack
- Fabricant: Graphtec
- Code à barres : 091128996115
9. Garantie et assistance
As an authentic Graphtec part, this product is covered by Graphtec's standard warranty policy for replacement parts. For specific warranty terms and conditions, please refer to the documentation provided with your Graphtec cutting plotter or visit the official Graphtec website.
For technical assistance, installation queries, or warranty claims, please contact your authorized Graphtec distributor or Graphtec customer support directly. Ensure you have your product model number (CE7000-130) and part number (PM-CR-011) available when seeking support.
Note: This manual is for the replacement cutting strip only. For operation, maintenance, and troubleshooting of your Graphtec CE7000 Series cutting plotter, please consult its dedicated user manual.
