1. Produit terminéview
The Orbit 67364 is a 1/4-inch by 50-foot pressure-compensating drip emitter tubing designed for efficient and targeted watering. This tubing features integrated emitters spaced every 12 inches, delivering a consistent flow rate of 0.50 GPH (gallons per hour). Constructed from UV-resistant low-density polyethylene, it is flexible and suitable for various garden applications.
Image 1.1: Orbit 67364 1/4-inch Drip Emitter Tubing, coiled.
Caractéristiques principales :
- Targeted Watering: Ideal for watering closely spaced plants, hedges, vegetable gardens, planter boxes, and ground cover.
- Integrated Emitters: UV-resistant polyethylene tubing with pre-installed drip emitters spaced every 12 inches.
- Flux constant : Pre-installed, pressure-compensating (PC) emitters deliver 0.50 GPH for 1/4-inch tubing.
- Dimensions standard : Nominal outside diameter of 0.25 inches.
- Large compatibilité: Compatible with 1/4-inch drip fittings from Orbit, Hydro-Rain, and other major brands.
2. Configuration et installation
Proper setup ensures optimal performance and water efficiency for your drip irrigation system.
Étapes d'installation :
- Planifiez votre mise en page : Determine the desired path for your drip tubing. This tubing can be installed above ground, under mulch, or bark, and is suitable for planter boxes, vegetable gardens, box gardens, or looping around individual plants and trees.
- Raccordement à une source d'eau : Attach the drip tubing system to a cold water source. Ensure all connections are secure to prevent leaks.
- Install Pressure Regulator and Filter (Recommended): For optimal performance and to prevent clogging, install a pressure regulator and filter (sold separately) upstream of the drip tubing. This should be placed immediately after the valve or hose faucet connection.
- Disposition des tubes : Carefully unroll and position the tubing according to your planned layout. Ensure emitters are positioned near the base of plants for direct watering.
- Tuyauterie sécurisée : Use drip stakes (sold separately) to hold the tubing firmly in place, especially in windy areas or on uneven terrain.
- Vérifier la compatibilité : Ensure all fittings used are compatible with 1/4-inch drip tubing.
Image 2.1: A person installing drip irrigation tubing around plants in a garden bed.
3. Mode d'emploi
Once installed, operating the Orbit 67364 drip emitter tubing is straightforward. The system is designed for continuous, low-volume watering.
Consignes d'utilisation :
- Water Source Activation: Turn on the cold water supply to your drip irrigation system.
- Débit: The integrated pressure-compensating emitters will automatically deliver a consistent 0.50 GPH of water per emitter, regardless of minor pressure fluctuations in your water line.
- Durée d'arrosage : Adjust the watering duration based on your plants' needs, soil type, and local climate. Drip irrigation typically requires longer watering times at lower frequencies compared to traditional sprinklers.
- Surveillance du système : Periodically observe the system during operation to ensure all emitters are dripping consistently and that water is reaching the intended areas without runoff.
- Cold Water Use Only: This product is designed exclusively for outdoor use with cold water. Do not connect to hot water lines.
Image 3.1 : Gros plan view of drip emitters delivering water directly to the base of a plant.
4. Entretien
Regular maintenance helps prolong the life of your drip system and ensures efficient watering.
Conseils d'entretien:
- Inspection régulière : Routinely inspect the entire length of the tubing for any signs of damage, such as cuts, punctures, or severe kinks. Repair or replace damaged sections promptly.
- Nettoyage du filtre : If a filter is installed in your system, clean it regularly according to the filter manufacturer's instructions. This prevents sediment and debris from clogging the drip emitters.
- Vérification de l'émetteur : Periodically verify that all emitters are dripping consistently. If an emitter appears blocked, gently try to clear it. Avoid using sharp objects that could damage the emitter.
- Lignes de rinçage : Occasionally, flush the drip lines by temporarily removing the end caps (if applicable) and allowing water to run through to clear out any accumulated debris.
- Hivernage (pour les climats froids) : Before the first freeze, disconnect the drip system from the water source. Drain all water from the tubing and components to prevent freezing and cracking. Store the tubing in a protected, dry area during winter months.
Image 4.1: A drip irrigation assortment kit showing various components for system maintenance and expansion.
5. Dépannage
If you encounter issues with your Orbit 67364 drip emitter tubing, refer to the following troubleshooting guide:
Problèmes courants et solutions :
- Low or No Water Flow from Emitters:
- Vérifier la source d'eau : Ensure the main water supply is fully open and providing adequate pressure.
- Inspect Pressure Regulator and Filter: If installed, check the pressure regulator for proper function and clean any debris from the filter. A clogged filter is a common cause of reduced flow.
- Examine Tubing for Kinks: Look for any kinks, sharp bends, or crimps in the tubing that might restrict water flow. Straighten the tubing as needed.
- Clear Emitter Blockages: Visually inspect individual emitters for dirt, mineral deposits, or other blockages. Gently try to dislodge any debris.
- Arrosage irrégulier :
- Tubing Placement: Ensure the tubing is laid out evenly and secured with stakes to prevent shifting, which can alter emitter positioning.
- Emitter Function: Verify that all emitters are clear and functioning correctly. Replace any emitters that are consistently not dripping or are spraying incorrectly.
- Pression du système: Confirm that the system pressure is within the recommended operating range for drip irrigation. Too high or too low pressure can affect emitter performance.
- Leaks in the System:
- Vérifier les connexions : Tighten all connections between the tubing and fittings.
- Inspecter les tubes : Look for punctures or cracks in the tubing. Small holes can sometimes be repaired with a coupling, while larger damage may require replacing a section of tubing.
6. Spécifications
Detailed specifications for the Orbit 67364 Drip Emitter Tubing:
| Spécification | Détail |
|---|---|
| Marque | Orbite |
| Numéro de modèle | 67364 |
| Matériel | Polyéthylène (PE) |
| Couleur | Brun |
| Dimensions du produit (L x l) | 50 Feet (600 inches) x 0.25 Inches |
| Poids de l'article | 0.27 kilogrammes (9.6 onces) |
| Épaisseur nominale de la paroi | 0.25 pouces |
| Diamètre extérieur | 0.25 pouces |
| Espacement des émetteurs | 12 pouces |
| Emitter Flow Rate | 0.50 GPH (gallons par heure) |
| Code UPC | 046878673649 |
| Fabricant | Orbit Irrigation |
| Utilisations spécifiques | Gardening, Plant Care |
7. Informations sur la garantie
This Orbit product is covered by a limited manufacturer's warranty. The warranty typically covers defects in materials and workmanship under normal use. For specific details regarding warranty coverage, duration, terms, and conditions, please refer to the official Orbit website or contact Orbit customer service directly. Keep your proof of purchase for warranty claims.
8. Assistance clientèle
For technical assistance, product inquiries, or to purchase accessories and replacement parts, please utilize the following resources:
- Officiel Website: Visitez le site officiel d'Orbit website for comprehensive product information, FAQs, and support resources: www.orbitonline.com
- Service client: Contact Orbit customer support directly for personalized assistance. Refer to the website pour les méthodes de contact actuelles (téléphone, courriel, clavardage).
