TURCK NI3-EG08K-AP6X-V1131 Proximity Sensor User Manual

1. Introduction

This manual provides essential information for the proper installation, operation, and maintenance of the TURCK NI3-EG08K-AP6X-V1131 Proximity Sensor. This inductive sensor is designed for non-contact detection of metallic objects.

Veuillez lire attentivement ce manuel avant d'utiliser le produit afin de garantir un fonctionnement sûr et efficace.

2. Consignes de sécurité

WARNING: Failure to follow these safety instructions may result in personal injury or equipment damage.

Assurez-vous que l'alimentation électrique est coupée avant toute installation, câblage ou maintenance.
Seul un personnel qualifié est habilité à installer et à entretenir cet appareil.
Ne dépassez pas le volume spécifiétage et les cotes actuelles.
Protect the sensor from mechanical impact and excessive vibration.
Do not modify the sensor. Unauthorized modifications may void the warranty and compromise safety.

3. Produit terminéview

The TURCK NI3-EG08K-AP6X-V1131 is an inductive proximity sensor with the following key features:

Modèle: NI3-EG08K-AP6X-V1131
Portée de détection : 3 mm
Logement: M8x1 Barrel, 8mm stainless steel full threading short barrel
Type de sortie : Normally Open (NO) PNP
Vol d'exploitationtage: 10-30 VCC
Connexion: M8 Male Connector (Picofast 3-Pin QD Connector)
Indicateur: 1 LED for operational status

This sensor is designed for reliable detection of metallic targets in industrial environments.

4. Configuration et installation

4.1 Montage

Select a mounting location where the sensor is protected from physical damage and excessive heat.
Mount the M8x1 barrel sensor using appropriate mounting hardware, ensuring it is securely fastened.
Maintain adequate clearance around the sensor head to prevent interference from surrounding metallic objects, especially for flush-mountable sensors. Refer to the sensor's datasheet for specific mounting distances.

4.2 Câblage

The sensor features a 3-pin M8 male connector. Follow the standard wiring color code for PNP sensors:

Pin 1 (Brown): +VDC (10-30VDC)
Pin 3 (Blue): 0VDC (Ground)
Pin 4 (Black): Output (PNP, Normally Open)

Connect the sensor to the control system according to the wiring diagram provided by the system manufacturer. Ensure all connections are secure and properly insulated.

5. Fonctionnement

Once properly installed and wired, apply power to the sensor. The integrated LED indicator will provide status feedback:

CONDUIT SUR: Indicates that a metallic object is within the sensing range and the output is active (PNP output is high).
LED éteinte: Indicates no metallic object is detected within the sensing range and the output is inactive (PNP output is low).

The sensor operates by generating an electromagnetic field. When a metallic object enters this field, it causes a change in oscillation, triggering the output. The 3mm sensing range ensures reliable detection for small to medium-sized metallic targets.

6. Entretien

The TURCK NI3-EG08K-AP6X-V1131 sensor is designed for minimal maintenance. However, regular inspection can prolong its lifespan and ensure reliable operation.

Nettoyage: Periodically clean the sensor face to remove dust, dirt, or debris that may accumulate and affect sensing performance. Use a soft, damp chiffon. N'utilisez pas de nettoyants abrasifs ou de solvants.
Inspection: Check wiring and connections for any signs of damage, corrosion, or loose contacts. Ensure the sensor is securely mounted and not subjected to excessive vibration.
Conditions environnementales : Veillez à ce que l'environnement de travail reste dans les plages de température et d'humidité spécifiées.

7. Dépannage

Problème	Cause possible	Solution
Sensor not detecting objects / LED always OFF	Pas d'alimentation électrique Câblage incorrect Object out of sensing range Capteur endommagé	Check power supply (10-30VDC). Vérifiez le câblage conformément à la section 4.2. Adjust target position within 3mm range. Remplacez le capteur s'il est endommagé.
Sensor always ON / LED always ON	Metallic object permanently in sensing range Interference from surrounding metal Capteur défectueux	Remove any metallic objects from the sensing area. Check mounting clearances. Replace sensor if faulty.
Détection intermittente	Connexions desserrées Vibration Target speed too high	Sécurisez tous les branchements électriques. Assurez-vous d'un montage stable. Verify target speed is within sensor capabilities (refer to datasheet).

8. Spécifications

Paramètre	Valeur
Numéro de modèle	NI3-EG08K-AP6X-V1131
Fabricant	Turck
Portée de détection	3 mm
Type de logement	M8x1 Barrel, 8mm stainless steel full threading short barrel
Type de sortie	PNP, normalement ouvert (NO)
Vol d'exploitationtage	10-30 VCC
Connexion	M8 Male Connector (Picofast 3-Pin QD)
Indicateur	1 LED
ASIN	B0898TS8W2
Date de première disponibilité	27 mai 2020

9. Garantie et assistance

For specific warranty information, please refer to the documentation provided with your purchase or contact Turck customer support directly. General warranty terms typically cover defects in materials and workmanship for a specified period from the date of purchase.

For technical assistance, troubleshooting beyond this manual, or to inquire about repairs, please contact Turck customer service or your authorized distributor. Have your model number (NI3-EG08K-AP6X-V1131) ready when contacting support.

Turck Officiel Website: www.turck.com