Okin 2 Button 5 Pin Recliner Hand Control with USB - Instruction Manual

Introduction

This manual provides instructions for the installation, operation, and maintenance of your Okin 2 Button 5 Pin Lift Chair or Power Recliner Hand Control with USB.

This control unit is designed for use with compatible lift chairs and power recliners, offering convenient control over reclining functions and a built-in USB charging port.

Caractéristiques du produit

• Matériel: Zinc alloy pane for durability.
• Chargement USB : 5V 2A output for mobile devices.
• Longueur du câble : Approximately 125cm (4.1Ft) recliner switch cable.
• Compatibilité: Works with Okin, Ashley Furniture, Dewert, Flexteel, Limoss, and many other power recliners using a 5-pin connection.

Okin 2 Button 5 Pin Recliner Hand Control with USB, showing the two control buttons and the USB charging port.

Configuration et installation

This section details the steps for replacing or installing the hand control unit.

Outils requis : Small flat-head screwdriver or putty knife (for prying), zip ties (optional, for cable management).

Étapes d'installation :

1. Débrancher l'alimentation : Ensure the recliner is unplugged from the electrical outlet before beginning installation.
2. Supprimer l'ancien contrôle : Carefully remove the existing hand control unit from its mounting location. This may involve gently prying it out of the armrest or side panel.
3. Déconnecter le câble : Disconnect the 5-pin connector of the old control from the recliner's motor or control box.
4. Connecter une nouvelle commande : Connect the new Okin 2 Button 5 Pin Hand Control's cable to the recliner's control box. Ensure the 5-pin connector is securely seated.
5. Câble de routage : Route the cable neatly and secure it with zip ties if necessary to prevent snagging or damage.
6. Unité d'installation : Insert the new hand control unit into the mounting hole. Ensure it clicks into place or is securely fastened using the provided circlips.
7. Rebrancher l'alimentation : Reconnect the recliner to the electrical outlet.

Explosé view diagram illustrating the components of the recliner hand control and its installation into a wooden frame, showing the switch cover, lower cover, circlips, and studs.

Close-up of the 5-pin connector, which connects the hand control to the recliner's motor system.

Mode d'emploi

The Okin 2 Button 5 Pin Hand Control provides simple operation for your power recliner.

Fonction inclinable :

• Extend Footrest / Recline: Appuyez et maintenez enfoncé le "EN HAUT" button to extend the footrest and recline the chair.
• Retract Footrest / Upright: Appuyez et maintenez enfoncé le "VERS LE BAS" button to retract the footrest and return the chair to its upright position.
• Note: Some recliner models may require continuous pressure on the button for the full range of motion.

Port de charge USB:

• The integrated USB port (5V 2A) is designed for charging mobile devices. Connect your device's USB cable to the port.
• Assurez-vous que le fauteuil inclinable est branché à une source d'alimentation pour que le port USB fonctionne.

Entretien

To ensure the longevity and proper function of your hand control unit:

• Nettoyage: Keep the unit clean by wiping it with a soft, dry cloth. Avoid abrasive cleaners or solvents, which can damage the surface or internal components.
• Inspection des câbles : Ensure cables are not pinched, twisted, or damaged. Regularly inspect the cable for any signs of wear, fraying, or cuts.
• Conditions environnementales : Do not expose the unit to excessive moisture, direct sunlight, or extreme temperatures.

Dépannage

L'unité de contrôle ne répond pas :

1. Vérification de l'alimentation : Verify that the recliner is properly plugged into a working power outlet.
2. Vérification de la connexion : Ensure that all cable connections, especially the 5-pin connector to the recliner's motor, are secure and fully inserted.
3. Dommages au câble : Inspect the control cable for any visible damage or cuts. A damaged cable may prevent proper function.
4. Motor/Power Supply: If the issue persists after checking connections and cable, the recliner's motor or power supply unit may need inspection by a qualified technician.

Le port USB ne charge pas :

1. Recliner Power: Ensure the recliner is powered on and connected to an electrical outlet. The USB port requires power from the recliner's system.
2. Cable/Device Check: Essayez un autre câble USB ou un autre appareil pour éliminer tout problème lié au câble de charge ou à l'appareil en charge.
3. Remplacement de l'unité : If the USB port still does not function, the control unit may require replacement.

Caractéristiques

Detailed dimensions of the Okin 2 Button 5 Pin Recliner Hand Control, showing measurements of 3.27 inches, 1.42 inches, and 3.9 inches.

Arrière view of the control unit, displaying product identification labels including P/N JLDK-17, DC 24V 2A, USB 5V 2A, and manufacturer Okin Refined Electric Technology Co., Ltd.

Garantie et assistance

For warranty information or technical support regarding this Okin 2 Button 5 Pin Recliner Hand Control, please refer to the documentation provided with your original recliner or contact the manufacturer directly. Specific warranty terms for this replacement part may vary.