ACR PLB-400

ACR ResQLink 400 Personal Locator Beacon User Manual

Model: PLB-400 | Brand: ACR

1. Introduction

The ACR ResQLink 400 is a compact, buoyant, GPS-enabled Personal Locator Beacon (PLB) designed to provide a direct link to rescue services in an emergency. When activated, it transmits a powerful 406 MHz distress signal to the Cospas-Sarsat satellite system, along with your precise GPS location, alerting search and rescue efforts worldwide. This device is intended for use in outdoor emergencies across various activities including hiking, hunting, boating, and fishing.

ACR ResQLink 400 Personal Locator Beacon

Image: The ACR ResQLink 400 Personal Locator Beacon, a compact, bright yellow and clear device.

Person hiking with ACR ResQLink 400 attached to backpack

Image: The ResQLink 400 attached to a backpack during a hike, demonstrating portability.

2. Principales caractéristiques

3. Configuration et inscription

Before using your ResQLink 400, it is critical to register your beacon with the appropriate national authority. In the United States, this is the National Oceanic and Atmospheric Administration (NOAA). Registration is free and mandatory. It provides search and rescue forces with vital information about you and your vessel/activity, which can significantly aid in a rescue operation.

For detailed activation instructions, please refer to the video below:

Video: ACR ResQlink 400 + 425 Activation Guide. This video demonstrates the steps to activate your Personal Locator Beacon in an emergency.

Initial Registration Steps:

  1. Visit the official beacon registration website for your country (e.g., NOAA for USA).
  2. Locate your beacon's Unique Identifier Number (UIN) or Hex ID, typically found on the device label.
  3. Complete the online registration form with accurate personal and emergency contact information.
  4. Keep your registration information up-to-date, especially if your contact details or emergency contacts change.

4. Operating the ResQLink 400 in an Emergency

The ResQLink 400 is designed for simple, rapid deployment in life-threatening situations. Follow these steps carefully:

  1. Deploy the Antenna: Slide the antenna cover up and extend the antenna fully. Ensure it is positioned at a 90-degree angle to the beacon and has a clear view du ciel pour une réception satellite optimale.
  2. Activate the Beacon: Press and hold the red "ON" button for approximately 2 seconds until the red LED light begins to flash. The device will start acquiring GPS coordinates and transmitting the distress signal.
  3. Confirm GPS Acquisition: Once GPS coordinates are acquired, the red LED will turn green, indicating a successful position fix. The strobe light will also begin to flash.
  4. Maintenir son poste : Leave the beacon in an open area with an unobstructed view of the sky. Do not turn it off until rescue personnel confirm your safety.
Person holding ACR ResQLink 400 on a boat

Image: A person holding the ACR ResQLink 400 Personal Locator Beacon on a boat, demonstrating its use in a marine environment.

5. Self-Test Procedure

Regular self-testing ensures your ResQLink 400 is functioning correctly. Perform a self-test monthly or before any extended trip.

Video: ACR ResQlink 400 + 425 Self-Test Guide. This video provides instructions on how to perform a self-test on your Personal Locator Beacon.

Steps for Self-Test:

  1. Deploy Antenna: Slide the antenna cover up and extend the antenna fully.
  2. Initiate Self-Test: Press and hold the "T" (Test) button for approximately 2 seconds.
  3. Observer les LED : The green LED will flash once, followed by a second green LED flash. If you have the "View" model, the display will confirm "SELF TEST PASS".
  4. Remarque importante : During the self-test, ensure you do not touch the antenna. Holding the antenna can interfere with the test and potentially cause it to fail.

If the self-test fails (e.g., red LED flashes, no display message, or "FAIL" message), consult the troubleshooting section or contact ACR support.

6. Maintenance et entretien

7. Dépannage

ProblèmeCause possibleSolution
Self-Test Fails (Red LED)Antenna not deployed correctly, low battery, internal fault.Ensure antenna is fully extended and not obstructed. Check battery expiration. If issue persists, contact ACR support.
No GPS Acquisition during activationObstrué view of sky, device not stationary.Déplacez-vous vers un espace ouvert et dégagé. view of the sky. Keep the device stationary during activation.
L'appareil ne s'allume pasDepleted or expired battery.Check battery expiration date. Contact ACR support for battery replacement.

8. Spécifications

9. Contenu de la boîte

10. Garantie et assistance

ACR Electronics, Inc. stands behind the quality and reliability of its products. For specific warranty details, service, or technical support, please refer to the official ACR webconsultez le site ou contactez directement leur service client.

Visitez le ACR Store on Amazon Pour plus d'informations et découvrir nos produits.

11. Informations importantes sur la sécurité

The ACR ResQLink 400 is a critical safety device. It is subject to regulations by various authorities, including Cospas-Sarsat and the FCC. Always ensure your device is properly registered and maintained according to local and international guidelines. This device is intended for emergency use only. False activation can result in penalties.

Avis de non-responsabilité juridique : Cospas-Sarsat, FCC

Documents connexes - PLB-400

Préview Guide d'installation de l'ACR ResQLink PLB pour le gilet de sauvetage Atlas 190 UML
Instructions étape par étape pour installer une balise de localisation personnelle (PLB) ACR ResQLink sur un gilet de sauvetage Atlas 190 UML, garantissant un fonctionnement sûr et correct.
Préview Instructions de montage du gilet de sauvetage ACR ResQlink AIS pour Atlas 190 Hammar
Guide étape par étape pour l'installation d'une balise de localisation personnelle (PLB) ACR ResQlink AIS sur un gilet de sauvetage Mustang Survival Atlas 190 Hammar, garantissant une installation correcte et sûre pour les situations d'urgence.
Préview Instructions pour ACR AISLink MOB vers ELITE 190 Gilet de sauvetage gonflable
Guide étape par étape sur la façon d'installer un dispositif ACR AISLink MOB sur un VFI gonflable ELITE 190, garantissant un fonctionnement sûr et correct.
Préview ACR GlobalFix V5 EPIRB User Manual: Installation, Operation & Safety Guide
Comprehensive user manual for the ACR GlobalFix V5 EPIRB, covering installation, operation, testing, and safety features for Category 1 and Category 2 models. Learn how this Emergency Position Indicating Radio Beacon with AIS and RLS enhances maritime safety and aids rescue coordination.
Préview ACR Sea Shelter™ 4 Mounting Template and Installation Guide
Download the ACR Sea Shelter™ 4 mounting template (Y1-06-0299 A) with detailed dimensions and critical installation cautions for EPIRB safety.
Préview Guide de montage et d'installation du projecteur ACR RCL-300A
Guide complet pour le montage et l'installation du système de projecteur ACR RCL-300A, comprenant le contrôleur maître URC-300 et le pointeur URP-102, avec des instructions de câblage détaillées et les caractéristiques.