Apollo 3/4" Bronze Double Union Threaded Water Pressure Regulator with Gauge Instruction Manual

1. Produit terminéview

The Apollo 3/4" Bronze Double Union Threaded Water Pressure Regulator with Gauge (Model 69ELF114TWG) is designed to reduce incoming water pressure to a safe and consistent level for residential and commercial plumbing systems. This unit features a compact design, lead-free bronze construction, and an integrated internal bypass mechanism. It includes a color-coded gauge for easy pressure monitoring and adjustment.

Figure 1: Apollo 3/4" Bronze Double Union Threaded Water Pressure Regulator with Gauge. This image shows the regulator with its integrated pressure gauge and yellow adjustment handle.

2. Consignes de sécurité

• Coupez toujours l'arrivée d'eau principale avant de commencer toute installation ou opération de maintenance.
• Portez un équipement de protection individuelle (EPI) approprié, tel que des lunettes de sécurité et des gants.
• Veillez à ce que tous les raccords soient correctement étanches afin d'éviter les fuites.
• Consult local plumbing codes and regulations for proper installation procedures.
• Si vous avez le moindre doute concernant une quelconque étape de l'installation, consultez un plombier qualifié.

3. Contenu du colis

Vérifiez que tous les composants sont présents avant de commencer l'installation :

• 1x Apollo 3/4" Bronze Double Union Threaded Water Pressure Regulator
• 1x Integrated Pressure Gauge

4. Installation

This regulator features a double union PEX-A (cold expansion) barb design for simplified installation in PEX-A piping systems. Ensure the regulator is installed in the correct flow direction, indicated by an arrow on the body.

1. Préparez le site d'installation : Turn off the main water supply. Drain the water lines to relieve pressure. Select a suitable location for the regulator, typically after the main shut-off valve and before any branch lines.
2. Cut and Prepare PEX-A Piping: Cut the PEX-A pipe to the required length, ensuring clean, square cuts. Prepare the pipe ends for cold expansion connections according to PEX-A system manufacturer guidelines.
3. Raccordez le régulateur :
   • Apply appropriate thread sealant (e.g., Teflon tape or pipe dope) to the male threads of the PEX-A fittings.
   • Thread the PEX-A fittings onto the double union ends of the regulator. Ensure the flow arrow on the regulator body points in the direction of water flow into the building.
   • Tighten the union nuts securely, but do not overtighten.
   • Perform cold expansion connections on the PEX-A pipe ends to the fittings according to PEX-A system manufacturer instructions.
4. Installer le manomètre : The pressure gauge is typically pre-installed. Ensure it is securely threaded into the designated port on the regulator body.
5. Rétablir l'approvisionnement en eau et vérifier l'absence de fuites : Slowly turn on the main water supply. Carefully inspect all connections for any signs of leaks. Tighten connections as necessary.

Figure 2 : Côté view of the Apollo Water Pressure Regulator, showing the double union PEX-A connections and the flow direction arrow. Note the "MAX INLET 400 PSI" marking.

5. Mode d'emploi

The regulator is factory-set at 50 psi and is adjustable from 15 psi to 75 psi. No special tools are required for adjustment.

1. Vérifiez la pression actuelle : Observe the reading on the integrated pressure gauge. The gauge is color-coded to indicate pressure ranges (e.g., Low, Optimal, Excessive).
2. Pression de réglage :
   • À augmenter pressure: Turn the yellow adjustment handle dans le sens des aiguilles d'une montre.
   • À diminuer pressure: Turn the yellow adjustment handle dans le sens antihoraire.
   • Make small adjustments and allow the system pressure to stabilize before re-checking the gauge.
3. Confirmer le réglage : Once the desired pressure is achieved (typically between 50-60 psi for most residential applications), confirm the reading on the gauge.

Figure 3 : Gros plan view of the Apollo Water Pressure Regulator, highlighting the pressure gauge with its color-coded optimal range and the yellow adjustment handle.

6. Entretien

The Apollo Water Pressure Regulator is designed for minimal maintenance. Regular checks can help ensure optimal performance.

• Periodic Pressure Check: Periodically check the pressure gauge to ensure the system pressure remains at the desired setting. Fluctuations may indicate a need for adjustment or inspection.
• Inspection des fuites : Annually inspect the regulator and connections for any signs of leaks or corrosion.
• Nettoyage: Clean the exterior of the regulator with a damp Utiliser un chiffon au besoin. Ne pas utiliser de produits chimiques agressifs.
• Sediment Filter (Optional): If your water supply contains significant sediment, consider installing a sediment filter upstream of the pressure regulator to prevent internal clogging.

7. Dépannage

8. Spécifications

• Modèle: 69ELF114TWG
• Matériel: Bronze
• Taille de connexion d'entrée : 3/4 pouces
• Type de connexion d'entrée : Cross Linked Polyethylene (PEX-A)
• Type de connexion de sortie : PEX
• Pression de service maximale : 400 PSI (Inlet)
• Plage de pression réglable : 15 - 75 PSI (Factory-set at 50 PSI)
• Dimensions de l'article (L xlxh): 2.13 x 7 x 8 pouces
• Poids de l'article : 2.53 livres
• Certifications: Certified to ASSE 1003 and CSA B356, listed by ASSE and IAPMO (cUPC)
• Caractéristiques spéciales : Integrated internal bypass mechanism, Color-coded gauge

9. Garantie et assistance

This Apollo Water Pressure Regulator comes with a manufacturer's warranty. For specific warranty details, please refer to the documentation included with your purchase or contact Apollo customer support.

For technical support or inquiries, please visit the official Apollo website ou contactez leur service client.