Introduction
The Armor3 "ReadyHub" 3-Port HD Switcher allows you to connect up to three HD game consoles or other HD devices to a single HD display, such as an HDTV or monitor. This device simplifies your setup by eliminating the need to constantly swap cables, providing a convenient way to switch between your connected devices with the push of a button or via the included remote control. It supports 4K resolution, ensuring high-quality video output.
Contenu du colis
Veuillez vérifier que tous les articles sont présents dans votre colis :
- Armor3 "ReadyHub" 3-Port HD Switcher
- Télécommande
- Power Adapter (typically included for active switchers)
Note: HD cables are not included and must be purchased separately.
Image: The Armor3 ReadyHub 3-Port HD Switcher shown in its retail packaging, highlighting its 4K and 3D compatibility.
Instructions d'installation
Follow these steps to connect your Armor3 "ReadyHub" HD Switcher:
- Connecter les périphériques d'entrée : Plug your HD game consoles (e.g., Nintendo Switch, PS4, Xbox One, Wii U, Xbox 360) or other HD devices into the "INPUT 1", "INPUT 2", and "INPUT 3" ports on the HD Switcher using HD cables.
- Se connecter à l'écran : Connect one end of an HD cable to the "OUTPUT" port on the HD Switcher and the other end to an available HD input port on your HDTV or display.
- Connecter l'alimentation : Plug the included power adapter into the "DC 5V" port on the HD Switcher, then plug the adapter into a standard electrical outlet. The power indicator light on the switcher should illuminate.
- Sélectionnez Entrée : Turn on your HD display and select the corresponding HD input channel that the switcher is connected to.
Image: The Armor3 ReadyHub HD Switcher with HD cables connected to its input and output ports, alongside its remote control. This illustrates a typical setup configuration.
Mode d'emploi
Once connected, you can easily switch between your devices:
- Commutation manuelle : Press the "SELECT" button on the front of the HD Switcher to cycle through the connected input devices (Input 1, Input 2, Input 3). The corresponding LED indicator will light up to show the active input.
- Commutation à distance : Use the included remote control to directly select the desired input. Press the "1", "2", or "3" button on the remote to switch to Input 1, Input 2, or Input 3 respectively.
Ensure that the device you wish to display is powered on for the switcher to detect its signal.
Entretien
To ensure the longevity and optimal performance of your Armor3 "ReadyHub" HD Switcher:
- Nettoyage: Utilisez un chiffon doux et sec pour nettoyer l'extérieur de l'appareil. N'utilisez pas de nettoyants liquides ni de produits abrasifs.
- Stockage: Store the switcher in a cool, dry place away from direct sunlight and extreme temperatures.
- Manutention: Évitez de faire tomber l'appareil ou de le soumettre à des chocs violents.
Dépannage
If you encounter issues with your HD Switcher, please refer to the following common problems and solutions:
| Problème | Solution |
|---|---|
| Aucun signal affiché. |
|
| La télécommande ne fonctionne pas. |
|
| Le voyant d’alimentation est éteint. |
|
Caractéristiques
- Modèle: M07385
- Entrées : 3 x HD (HDMI)
- Sortir: 1 x HD (HDMI)
- Résolutions prises en charge : Jusqu'à 4 XNUMX
- Compatibilité: Nintendo Switch, PlayStation 4, Xbox One, Nintendo Wii U, Xbox 360, and other HD devices.
- Dimensions: 4.72 x 1.57 x 4.75 pouces (12 x 4 x 12.06 cm)
- Poids: 3.2 onces (90.7 grammes)
Garantie et assistance
For warranty information or technical support, please contact Armor3 customer service. Details can typically be found on the product packaging or the official Armor3 webVeuillez conserver votre preuve d'achat pour toute réclamation au titre de la garantie.
Pour obtenir de l'aide supplémentaire, vous pouvez consulter le site web du fabricant. webconsultez le site ou contactez leurs services d'assistance.
