1. Introduction
The Seco-Larm SK-917T2-GNQ Enforcer Pendant RF Transmitter is designed to provide wireless control for various applications and devices. This device operates at 315MHz and is compatible with all Seco-Larm 315MHz receivers. It can be used to control functions such as garage doors, gates, home lighting, or alarm panels, offering convenient remote operation. Its compact, slimline design includes a keychain for portability.
Image 1.1: The Seco-Larm SK-917T2-GNQ Enforcer Pendant RF Transmitter. This black, rectangular device features two distinct buttons labeled '1' and '2' on its surface. The brand name 'ENFORCER' is visible below the buttons. A metal keychain ring is attached to the transmitter, enhancing its portability.
2. caractéristiques du produit
- Contrôle sans fil : Enables remote operation of compatible devices with the push of a button.
- CODEBUMP Technology: Incorporates anti-code grabbing technology for enhanced security.
- Compatibilité: Fully compatible with all 315MHz Seco-Larm receivers.
- High Security Codes: Offers over 18 quintillion possible codes to prevent unauthorized access.
- Plage de fonctionnement étendue : Operates up to 500 feet, depending on installation and environmental factors.
- LED Transmission Indicator: Provides visual confirmation of signal transmission.
- RF Anti-Scan Protection: Further enhances security against scanning attempts.
- Conception élancée : Compact and portable, includes a keychain for easy carrying.
- Two Buttons, Three Channels: Provides control over multiple functions.
3. Contenu du colis
Vérifiez que tous les éléments sont présents dans le colis :
- Seco-Larm SK-917T2-GNQ Enforcer Pendant RF Transmitter with Keychain
- Pile CR2032 (préinstallée ou incluse)
4. Installation
4.1. Installation/activation de la batterie
The transmitter comes with a CR2032 battery. In most cases, the battery is pre-installed. If the transmitter does not respond, or if the LED indicator does not light up when a button is pressed, the battery may need to be activated or replaced. Refer to the "Maintenance: Battery Replacement" section for instructions.
4.2. Appairage avec un récepteur
To function, the SK-917T2-GNQ transmitter must be paired or "learned" into a compatible 315MHz Seco-Larm receiver. The specific pairing procedure varies depending on the model of your Seco-Larm receiver. Please refer to the instruction manual provided with your Seco-Larm receiver for detailed pairing instructions.
- Ensure your Seco-Larm receiver is powered on and in programming mode (refer to receiver manual).
- Press the desired button(s) on the SK-917T2-GNQ transmitter as instructed by your receiver's manual to transmit the code.
- Confirm successful pairing via the receiver's indicator (e.g., LED flash, audible beep).
5. Fonctionnement
Once the transmitter is successfully paired with your Seco-Larm receiver, you can operate your connected devices.
- Fonctions des boutons : The SK-917T2-GNQ features two buttons, typically labeled '1' and '2'. These buttons can be programmed to control different functions or devices depending on your receiver's capabilities and your programming choices.
- Transmission d'un signal : Press and hold the desired button for approximately one second. The LED indicator on the transmitter will illuminate, confirming that a signal is being transmitted.
- Appareils de contrôle : The receiver will interpret the transmitted signal and activate the corresponding device or function (e.g., open a garage door, turn on a light, arm/disarm an alarm system).
For specific actions associated with each button, refer to your receiver's programming documentation.
6. Entretien
6.1. Remplacement de la batterie
The transmitter is powered by a single CR2032 lithium coin cell battery. When the LED indicator becomes dim or fails to light up during button presses, it is time to replace the battery.
- Locate the small notch or seam on the side of the transmitter casing.
- Ouvrez délicatement le casing à l'aide d'un petit tournevis plat ou d'un outil similaire.
- Remove the old CR2032 battery, noting its polarity (+ side up).
- Insérez une nouvelle pile CR2032 avec le côté positif (+) vers le haut.
- Alignez les deux moitiés du casing et pressez-les fermement l'un contre l'autre jusqu'à ce qu'ils se ferment d'un coup.
- Test the transmitter by pressing a button and observing the LED indicator.
Prudence: Dispose of used batteries according to local regulations. Keep batteries out of reach of children.
7. Dépannage
- L'émetteur ne répond pas :
- Vérifiez la pile : assurez-vous que la pile CR2032 est correctement installée et suffisamment chargée. Remplacez-la si nécessaire.
- Verify pairing: Confirm that the transmitter is properly paired with your Seco-Larm receiver. Refer to your receiver's manual for pairing instructions.
- Obstructions: Ensure there are no significant physical obstructions between the transmitter and the receiver.
- Portée opérationnelle réduite :
- Environmental factors: Thick walls, metal structures, or other electronic devices can interfere with RF signals.
- Battery level: A low battery can reduce the effective transmission range. Replace the battery if needed.
- Interference: Other 315MHz devices or strong electromagnetic fields might cause interference.
- Le voyant LED ne s'allume pas :
- Battery issue: The battery is likely depleted or incorrectly installed. Replace or re-install the battery.
- Transmitter malfunction: If battery replacement does not resolve the issue, the transmitter may be faulty.
8. Spécifications
| Fonctionnalité | Détail |
|---|---|
| Numéro de modèle | SK-917T2-GNQ |
| Taper | 2 boutons, 3 canaux |
| Fréquence RF | 315 MHz |
| Plage de fonctionnement | Up to 500 feet (line of sight, environment dependent) |
| Nombre de codes | Over 18 quintillion |
| Type de batterie | CR2032 (inclus) |
| Dimensions | 1-1/4 x 2-3/16 x 5/16 pouces (31.5 x 55 x 8 mm) |
| Poids | 0.95 onces |
| Certifications | FCC, CI |
9. Informations sur la garantie
The Seco-Larm SK-917T2-GNQ Enforcer Pendant RF Transmitter comes with a Garantie limitée de 2 ans from the date of purchase. This warranty covers defects in materials and workmanship under normal use. It does not cover damage resulting from misuse, accident, unauthorized modification, or improper installation. Please retain your proof of purchase for warranty claims.
10. Assistance
For further assistance, technical support, or warranty inquiries, please contact Seco-Larm customer service. Refer to the official Seco-Larm webPour obtenir les coordonnées les plus récentes, veuillez consulter le site web ou l'emballage du produit.
