Éclairage Sunco DL_SL6-14W

Sunco Lighting 6-Inch Ultra-Thin LED Recessed Light Manual

Modèle : DL_SL6-14W

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your Sunco Lighting 6-Inch Ultra-Thin LED Recessed Ceiling Lights. These 14W, 5000K Daylight fixtures are designed for easy installation without a can, featuring a wafer-thin profile and an integrated junction box. They offer seamless dimming capabilities and are IC rated for direct contact with insulation.

Consignes de sécurité

Qu'y a-t-il dans la boîte

Chaque package contient les composants suivants :

Caractéristiques

FonctionnalitéDétail
Numéro de modèleDL_SL6-14W
Taille6 pouces
Température de couleurLumière du jour 5000K
Quoitage14 watts
Luminosité850 lumens
Voltage120 volts
GradableOui (10%-100%)
MatérielPolycarbonate, Copper Wiring
Utilisation intérieure/extérieureIntérieur
CertificationsEnergy Star, ETL (5005842), FCC (L10), RoHS
Poids de l'article0.01 onces (par unité)
Dimensions du produit7 x 1 x 7 pouces

Note: Efficiency is approximately 61 lumens per watt.

Diagram showing the dimensions of the 6-inch ultra-thin LED recessed light and its separate junction box.

Image: Detailed dimensions of the light fixture and junction box.

Configuration et installation

These ultra-thin LED recessed lights are designed for easy, canless installation. Follow these steps for proper setup:

Outils requis :

Étapes d'installation :

  1. Couper l'alimentation : Before starting, ensure the power to the installation area is turned off at the circuit breaker to prevent electrical shock.
  2. Découper un trou dans le plafond : Use a hole saw to cut a 6-inch diameter hole in the desired ceiling location. Ensure there are no obstructions (e.g., joists, pipes) behind the ceiling.
  3. Connecter le câblage : Open the junction box. Connect the house electrical wires to the fixture wires using the provided wire nuts:
    • Black (Live) to Black (Fixture)
    • White (Neutral) to White (Fixture)
    • Green or Bare Copper (Ground) to Green (Fixture)
    Fermez soigneusement la boîte de jonction.
  4. Place Junction Box: Insert the junction box into the ceiling hole. The compact design allows it to sit above the ceiling.
  5. Installer le luminaire : Connect the light fixture to the junction box cable. Fold the spring-loaded clips on the side of the light fixture upwards and push the fixture into the ceiling hole. The clips will automatically snap down and hold the fixture securely in place.
  6. Tester la lumière : Rétablissez le courant au niveau du disjoncteur et testez le luminaire.
Diagram showing the installation of a recessed light with junction box and spring clips

Image: Installation diagram showing the junction box connected to house wiring and the light fixture with spring clips.

Vidéo : Un overview of Sunco Lighting's commitment to quality and customer service, including product testing and design.

Mode d'emploi

Your Sunco Lighting LED recessed lights are designed for simple operation and enhanced functionality.

Marche/Arrêt :

Operate the lights using a standard wall switch connected to the circuit. Flip the switch to turn the lights on or off.

Fonctionnalité de gradation :

These LED fixtures are fully dimmable from 10% to 100%. To utilize the dimming feature, ensure you have a compatible LED dimmer switch installed on the circuit. Adjust the dimmer switch to achieve your desired brightness level.

Image showing a room with recessed lights, split into two halves: one dark with lights at 10% brightness, and one bright with lights at 100% brightness, with a dimmer switch graphic.

Image: Visual representation of the smooth dimming capability from 10% to 100%.

Entretien

The Sunco Lighting LED recessed lights require minimal maintenance.

Dépannage

If you encounter issues with your LED recessed lights, refer to the following common problems and solutions:

ProblèmeCause possibleSolution
La lumière ne s'allume pas.No power, loose wiring, faulty switch, or faulty fixture.Check circuit breaker. Verify all wire connections are secure. Test the switch. If issues persist, contact support.
La lumière vacille ou faiblit de façon irrégulière.Incompatible dimmer switch, loose wiring, or voltage fluctuations.Ensure a compatible LED dimmer switch is used. Check wiring connections. Consult an electrician for voltage problèmes.
La lumière n'est pas aussi forte que prévu.Dimmer setting too low, or incorrect light placement.Adjust dimmer to 100%. Consider adding more fixtures for larger areas if needed.

Informations sur la garantie

Sunco Lighting fournit un Protection d'un an warranty for this product. This warranty covers defects in materials and workmanship under normal use. For warranty claims or further details, please contact Sunco Lighting customer support.

Des plans de protection supplémentaires peuvent être disponibles à l'achat auprès de détaillants agréés.

Soutien

For technical assistance, troubleshooting, or warranty inquiries, please contact Sunco Lighting customer support. Our knowledgeable specialists are available to assist you.

Visit the official Sunco Lighting website contenant des informations de contact et des ressources supplémentaires : www.suncolighting.com