Introduction
This manual provides comprehensive instructions for the safe and efficient use of your Paulmann MaxLED 79797 RGBW Controller. This device allows you to control Paulmann MaxLED RGBW light strips, enabling functions such as switching, dimming, and changing light colors and effects via the included wireless remote control. The controller operates without requiring direct line-of-sight to the remote, offering a range of up to 30 meters.
Consignes de sécurité importantes
- Lisez attentivement toutes les instructions avant l'installation et l'utilisation.
- Conservez ce manuel pour référence ultérieure.
- Ce produit est conçu pour une utilisation en intérieur uniquement (indice de protection IP20). Ne pas exposer à l'humidité ni aux températures extrêmes.
- Assurez-vous que l'alimentation électrique est débranchée avant toute installation ou opération de maintenance.
- Only use with Paulmann MaxLED RGBW strips and compatible 24V power supplies.
- Do not attempt to open or modify the controller or remote control. This will void the warranty.
- Gardez les piles hors de portée des enfants. Jetez les piles usagées de manière responsable.
Contenu du colis
Vérifiez que tous les composants sont présents dans le package :
- 1x Paulmann MaxLED RGBW Controller (Model 79797)
- 1x télécommande sans fil
- 1x Assembly Instructions (this manual)
Image: The MaxLED RGBW Controller and its wireless remote control. The controller is a small white rectangular unit with a cable, and the remote is an oval-shaped white device with various buttons and a color wheel.
Image: Diagram showing the MaxLED RGBW Controller and remote control with their approximate dimensions. The controller measures 22.5x85x45mm and the remote 20x110x53mm. A 150mm cable connects the controller to the LED strip.
Configuration et installation
Follow these steps for proper installation of your MaxLED RGBW Controller:
- Préparez la zone d'installation : Ensure the surface where the LED strip will be mounted is clean, dry, and free of dust.
- Connecter la bande LED : Connect your Paulmann MaxLED RGBW strip to the output cable of the controller. The system uses an easy plug-in connection. Ensure the connectors are securely fastened.
- Connectez l'alimentation : Connect a compatible 24V Paulmann power supply (not included) to the input side of the MaxLED RGBW Controller.
- Montez le contrôleur : The controller is designed for hidden installation. Place it in a discreet location where it is protected from physical damage and moisture, but still allows for proper signal transmission from the remote (up to 30m range).
- Mise sous tension : Once all connections are secure, plug the power supply into a suitable electrical outlet.
- Pairing the Remote Control (if necessary): The remote control is usually pre-paired. If not, refer to the "Operating Instructions" section for pairing procedures.
Image: This image illustrates the MaxLED expandable component system, highlighting three key aspects: "Easy to connect" (showing a hand connecting an LED strip), "Easy to mount" (showing an LED strip being applied to a surface), and "Easy to control" (showing the remote control). This demonstrates the simplicity of the setup process.
Mode d'emploi
The wireless remote control allows full command over your MaxLED RGBW strips.
Fonctions de la télécommande :
Image : Une image détaillée view of the MaxLED RGBW remote control, showing its various buttons and the central color wheel. The remote features power, brightness, mode, speed, and color selection controls.
- Bouton d'alimentation (O): Press to turn the LED strips On or Off.
- Réglage de la luminosité (B +/-): Use the '+' button to increase brightness and '-' to decrease brightness.
- Roue chromatique : Touch the color wheel to select a desired static color for your LED strips.
- Mode Selection (M): Cycle through various pre-programmed light effects and color changing modes.
- Contrôle de vitesse (S +/-): When in a dynamic mode, use the '+' button to increase the speed of the effect and '-' to decrease it.
Couplage de la télécommande :
If your remote control is not responding, it may need to be paired with the controller:
- Assurez-vous que le contrôleur est sous tension.
- Within 3 seconds of powering on the controller, press and hold the "Mode" (M) button on the remote control for a few seconds.
- The LED strips should flash to indicate successful pairing.
Entretien
Nettoyage:
To clean the controller and remote control, gently wipe with a soft, dry cloth. Do not use abrasive cleaners, solvents, or excessive moisture, as this can damage the components.
Remplacement de la pile de la télécommande:
The remote control requires batteries (type not specified in product data, typically CR2032 or similar button cell). If the remote's range decreases or it stops responding, replace the battery:
- Localisez le compartiment à piles à l'arrière de la télécommande.
- Ouvrez le compartiment à l'aide d'un petit tournevis ou en faisant glisser le couvercle.
- Retirez l'ancienne pile et insérez-en une nouvelle en veillant à respecter la polarité (+/-).
- Fermez soigneusement le compartiment à piles.
- Éliminez l’ancienne batterie conformément aux réglementations locales.
Dépannage
| Problème | Cause possible | Solution |
|---|---|---|
| LED strips do not light up. | No power, loose connection, faulty power supply, remote not paired. | Check power supply connection. Ensure all cables are securely plugged in. Verify power outlet is functional. Re-pair the remote control (see Operating Instructions). |
| La télécommande ne répond pas. | Dead battery, remote not paired, out of range. | Replace remote control battery. Re-pair the remote control. Move closer to the controller (within 30m). |
| Les couleurs sont incorrectes ou incohérentes. | Loose connection to LED strip, faulty LED strip. | Check the connection between the controller and the LED strip. Ensure the strip is fully compatible. |
| Dimming or effects not working. | Remote control issue, incompatible LED strip. | Ensure the remote control battery is good and it is paired. Verify the LED strip is an RGBW dimmable type. |
Caractéristiques
| Marque | Paulman |
| Numéro de modèle | 79797 |
| Dimensions du produit (L x l x H) | 5.3 x 11 x 2 cm (Controller); 20 x 110 x 53 mm (Remote) |
| Poids | 102 grammes |
| Indice de protection IP | IP20 (utilisation en intérieur uniquement) |
| Matériel | Plastique |
| Max. Vattage | 144 watts |
| Voltage | 24 volts |
| Type de source lumineuse | LED (for compatible strips) |
| Source d'énergie | AC (via external 24V power supply) |
| Caractéristiques spéciales | Dimmable, Variable Intensity, Remote Control, RGBW Color Change |
| Fréquence de la télécommande | RF 2.4 GHz |
| Portée de la télécommande | Up to 30 meters (non-line-of-sight) |
| Piles requises (télécommande) | Oui (non inclus) |
Image: The MaxLED RGBW Controller and its remote control, emphasizing the 2.4 GHz RF wireless technology for reliable communication.
Garantie et assistance
Garantie:
Paulmann offers a 1-year availability for spare parts for this product. For specific warranty terms and conditions, please refer to the official Paulmann webou contactez votre revendeur.
Assistance clientèle :
For further assistance, technical support, or inquiries regarding your Paulmann MaxLED RGBW Controller, please visit the official Paulmann website or contact their customer service department. Contact information can typically be found on the product packaging or the Paulmann website.
Paulman Website: www.paulmann.com
