1. Introduction
This manual provides essential instructions for the safe and correct installation, operation, and maintenance of the Satco 80-2627 Two-Light Ballast Bypass Wiring Harness. This harness is designed to convert existing fluorescent fixtures to operate with linear LED T8 lamps that require a ballast bypass (direct wire) installation. Please read all instructions thoroughly before beginning installation.
2. Consignes de sécurité
AVERTISSEMENT : Risque d’électrocution. L’installation requiert des connaissances en systèmes électriques de luminaires. Si vous n’êtes pas qualifié, n’essayez pas l’installation. Contactez un électricien qualifié.
- Always disconnect power at the circuit breaker or fuse box before installation, servicing, or removing the fixture.
- Assurer le vol d'alimentationtage is correct for the LED T8 lamps en cours d'installation.
- Ne faites pas et ne modifiez pas de trous ouverts dans un boîtier de câblage ou de composants électriques pendant l'installation du kit.
- Pour éviter tout dommage ou abrasion du câblage, n'exposez pas le câblage aux bords de la tôle ou à d'autres objets tranchants.
- This product is intended for use with specific LED T8 lamps designed for ballast bypass operation. Consult the LED lamp manufacturer's instructions for compatibility and wiring diagrams.
- Portez un équipement de protection individuelle (EPI) approprié, tel que des lunettes de sécurité et des gants, lors de l'installation.
- Assurez-vous que toutes les connexions sont sécurisées et correctement isolées.
3. Produit terminéview
The Satco 80-2627 wiring harness simplifies the conversion of a two-lamp fluorescent fixture to operate with ballast bypass LED T8 lamps. It includes pre-wired lamp holders (sockets) and a quick-connect terminal for easy connection to the main power supply.
Image 1: Components of the Satco 80-2627 Ballast Bypass Wiring Harness, showing the pre-wired lamp holders and quick-connect terminal.
4. Configuration et installation
Follow these steps carefully to install the Satco 80-2627 wiring harness:
- Débrancher l'alimentation : Turn off power to the fixture at the circuit breaker or fuse box. Verify power is off using a voltage testeur avant de continuer.
- Access Fixture Wiring: Open the fixture to access the existing ballast and wiring. Remove any covers or diffusers as necessary.
- Remove Existing Ballast: Disconnect all wires from the existing fluorescent ballast. Carefully remove and dispose of the old ballast according to local regulations.
-
Installer le nouveau Lamp Titulaires : Supprimer le l existantamp holders (sockets) from the fixture. Install the new pre-wired lamp holders from the Satco 80-2627 harness into the fixture, ensuring they are securely seated.
Image 2: Illustration of the easy installation process, showing the harness with new lamp holders ready for connection.
- Wire the Harness: Connect the quick-connect terminal of the Satco 80-2627 harness to the fixture's main power supply wires (Line and Neutral). Ensure proper polarity as indicated by the wiring diagram on the LED T8 lamps or fixture. Typically, one side of the LED T8 lamp receives Line voltage, and the other side receives Neutral. The harness is designed to provide these connections to the lamp détenteurs.
- Câblage sécurisé : Ensure all wiring is neatly routed and secured, preventing pinching or contact with sharp edges. Replace any wiring covers.
- Install LED T8 Lamps: Insert the ballast bypass LED T8 lamps into the new lamp holders. Ensure they are fully seated and twisted into place.
- Fermer le luminaire : Replace any fixture covers or diffusers that were removed.
- Restaurer l'alimentation : Turn power back on at the circuit breaker or fuse box. Test the new LED lighting system.
5. Mode d'emploi
Once installed, the Satco 80-2627 Ballast Bypass Wiring Harness operates seamlessly with your fixture's existing wall switch. Simply use the wall switch to turn the LED T8 lampest allumé ou éteint.
6. Entretien
The Satco 80-2627 wiring harness requires minimal maintenance. Periodically, it is recommended to:
- Inspection visuelle : With power disconnected, visually inspect the wiring and connections for any signs of wear, damage, or loose connections.
- Nettoyage: If necessary, gently wipe down the exterior of the lamp holders with a dry, lint-free cloth. Do not use liquid cleaners near electrical components.
7. Dépannage
Si vous rencontrez des problèmes après l'installation, veuillez consulter le guide de dépannage suivant :
| Problème | Cause possible | Solution |
|---|---|---|
| Lamps do not turn on. |
|
|
| Lamps flicker or dim. |
|
|
If troubleshooting steps do not resolve the issue, contact a qualified electrician or Satco customer support.
8. Spécifications
- Numéro de modèle : 80-2627
- Fabricant: Satco
- Numéro de pièce : 80-2627
- Dimensions du produit : Dimensions approximatives : 10 x 10 x 10 pouces (emballage)
- Poids de l'article : 1 livre
- Source d'alimentation : Électrique avec fil
- Nombre de Lamps Prise en charge : Deux (2)
- Compatible Lamp Taper: Linear LED T8 Lamps (Ballast Bypass / Direct Wire)
- Composants inclus : Satco 80-2627 Two Light Ballast Bypass Wiring Harness
9. Informations sur la garantie
For warranty information regarding the Satco 80-2627 Two-Light Ballast Bypass Wiring Harness, please contact the manufacturer directly. Warranty terms and conditions may vary.
Coordonnées du fabricant : Refer to Satco's official webPour obtenir les coordonnées les plus récentes, veuillez consulter le site web ou l'emballage du produit.
10. Assistance
If you require further assistance or have questions not covered in this manual, please contact Satco customer support. Ensure you have your product model number (80-2627) available when contacting support.
Satco Website: www.satco.com
