Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your Project Source Chrome 1-Handle Pull-Down Kitchen Faucet, model 51-K814-PS-CP. Please read this manual thoroughly before beginning installation and retain it for future reference.
Consignes de sécurité
- Coupez toujours l'arrivée d'eau principale avant d'installer ou d'entretenir le robinet.
- Wear safety glasses and gloves during installation to prevent injury.
- Assurez-vous que tous les raccords sont bien fixés afin d'éviter les fuites.
- Si vous avez des doutes concernant une quelconque étape du processus d'installation, consultez un plombier qualifié.
Contenu du colis
Vérifiez que tous les composants sont présents avant de commencer l'installation :
Figure 1 : All components of the Project Source pull-down kitchen faucet, including the main faucet body, hot and cold water supply lines, mounting hardware, deck plate, and instruction manual.
- Main Faucet Body with Pull-Down Sprayer
- Hot and Cold Water Supply Lines (pre-attached)
- Mounting Hardware (nut, washer, gasket)
- Deck Plate (optional, for 3-hole sinks)
- Weight (for pull-down hose)
- Manuel d'instructions
Configuration et installation
Outils requis :
- Clé à molette
- Tournevis cruciforme
- Mastic de plombier ou mastic silicone
- Bucket (for catching drips)
- Lampe de poche
Étapes d'installation :
- Préparer l'évier : Turn off the hot and cold water supply valves under the sink. Open the existing faucet to drain any remaining water. Disconnect and remove the old faucet. Clean the sink surface thoroughly.
- Install Deck Plate (Optional): If your sink has three holes, place the deck plate (if using) over the sink holes. Apply a thin bead of plumber's putty or silicone sealant around the underside edge of the deck plate to create a watertight seal.
- Montez le robinet : Insert the faucet body through the center hole of the sink (and deck plate, if used). From underneath the sink, slide the rubber washer, then the metal washer, and finally thread the mounting nut onto the faucet shank. Hand-tighten, then use an adjustable wrench to secure it firmly, ensuring the faucet is properly aligned.
- Raccordement des conduites d'alimentation en eau : Connect the hot and cold water supply lines from the faucet to the corresponding hot and cold water supply valves. The faucet's lines are typically labeled (e.g., "HOT" for hot water). Hand-tighten, then use an adjustable wrench for a final quarter-turn. Do not overtighten.
- Install Hose Weight: Locate the indicator on the pull-down hose (usually a sticker or mark) where the weight should be installed. Attach the provided weight to the pull-down hose at this indicated position. This weight helps the sprayer retract smoothly.
- Vérifiez les fuites : Slowly turn on the hot and cold water supply valves. Check all connections for leaks. If leaks are present, tighten the connections slightly until the leak stops.
- Tirez la chasse d'eau : Remove the sprayer head and turn on the faucet to flush out any debris from the lines. Let the water run for a few minutes. Turn off the faucet, reattach the sprayer head, and check for proper operation.
Mode d'emploi
- Débit et température de l'eau : The single handle controls both water flow and temperature. Lift the handle to increase water flow. Move the handle to the left for hot water and to the right for cold water.
- Pulvérisateur à extraction vers le bas : Grasp the sprayer head and pull it down from the spout. The hose will extend to allow for greater reach. Press the button on the sprayer head to switch between stream and spray functions. When finished, guide the sprayer head back into the spout; the hose weight will assist in retraction.
Entretien
- Nettoyage: Clean the faucet regularly with a soft cloth and mild soap. Avoid abrasive cleaners, harsh chemicals, or scouring pads, as these can damage the chrome finish.
- Nettoyage de l'aérateur : If water flow decreases, the aerator may be clogged. Unscrew the aerator from the tip of the sprayer head, clean any debris, and rinse thoroughly before reattaching.
- Hose Weight Adjustment: If the pull-down sprayer does not retract smoothly, check the position of the hose weight. Adjust its position along the hose as needed to ensure proper retraction.
Dépannage
| Problème | Cause possible | Solution |
|---|---|---|
| Faible débit d'eau | Aérateur obstrué ; vannes d'alimentation partiellement fermées. | Clean aerator; fully open supply valves. |
| Fuites chez Connections | Connexions desserrées ; rondelles endommagées. | Resserrer les raccords ; remplacer les rondelles si elles sont endommagées. |
| Le pulvérisateur ne se rétracte pas | Hose weight is misplaced or missing; obstruction. | Adjust or reattach hose weight; clear any obstructions. |
| Robinet qui goutte | Cartouche usée. | Contactez le service client pour le remplacement de la cartouche. |
Caractéristiques
| Fonctionnalité | Détail |
|---|---|
| Numéro de modèle | 51-K814-PS-CP |
| Marque | Origine du projet |
| Couleur | Chrome |
| Style | Contemporain |
| Finition | Brillant |
| Matériel | Céramique (pour cartouche) |
| Méthode d'installation | Trou Simple |
| Débit | 1.8 gallons par minute |
| Nombre de poignées | 1 |
| Type de montage | Montage sur le pont |
| Caractéristiques spéciales | Pulvérisateur escamotable |
| Dimensions du produit | 27.43 x 8.64 x 64.52 cm |
| Poids de l'article | 2.34 kg |
Garantie et assistance
For warranty information or technical support, please refer to the contact details provided with your purchase documentation or visit the official Project Source webConsultez le site. Conservez votre reçu d'achat comme preuve d'achat pour toute réclamation au titre de la garantie.
