Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of the Custom Dynamics ProBEAM 5 3/4" LED Headlamp, model PB-575-B. Please read this manual thoroughly before installation and use to ensure proper function and safety.
Figure 1 : Devant view of the Custom Dynamics ProBEAM 5 3/4" LED Headlamp (PB-575-B). This image shows the clear lens, the upper LED light bars, and the lower projector-style LED elements, along with the Custom Dynamics logo at the bottom.
Consignes de sécurité
Respectez toujours les consignes de sécurité suivantes :
- Débranchez la batterie du véhicule avant d'effectuer toute intervention électrique.
- Assurez-vous que toutes les connexions sont bien fixées et correctement isolées afin d'éviter les courts-circuits.
- Consultez un technicien qualifié si vous avez des doutes concernant les étapes d'installation.
- Do not modify the headlamp in any way, as this may void the warranty and compromise safety.
- Portez un équipement de protection individuelle (EPI) approprié lors de l'installation.
Contenu du colis
Vérifiez que tous les composants sont présents avant de commencer l'installation :
- 1x Custom Dynamics ProBEAM 5 3/4" LED Headlamp (PB-575-B)
- 1x Wiring Harness (if applicable, check product packaging)
- 1x Manuel d'instructions (ce document)
Configuration et installation
- Préparation: Park the vehicle on a level surface and turn off the ignition. Disconnect the negative terminal of the vehicle's battery.
- Remove Existing Headlamp: Carefully remove the bezel or retaining ring securing the existing 5 3/4" headlamp. Disconnect the wiring harness from the old headlamp.
- Install ProBEAM Headlamp: Connect the wiring harness of the ProBEAM LED headlamp to the vehicle's headlamp connector. Ensure the connection is secure.
- Secure Headlamp: Place the ProBEAM LED headlamp into the headlamp bucket. Reinstall the retaining ring or bezel to secure the headlamp en place.
- Rebranchez la batterie : Rebranchez la borne négative de la batterie du véhicule.
- Fonctionnalité de test : Turn on the vehicle's ignition and test the headlamp's low beam, high beam, and any integrated auxiliary functions (e.g., daytime running lights, if applicable).
- Visée: Ajustez la têteamp aim according to local regulations and for optimal visibility without blinding oncoming traffic. Refer to your vehicle's service manual for specific aiming procedures.
Note: Specific installation steps may vary depending on the vehicle model. Always refer to your vehicle's service manual for detailed instructions on removing and installing headlamps.
Mode d'emploi
The Custom Dynamics ProBEAM LED Headlamp operates in conjunction with your vehicle's existing headlamp switch. It features both low beam and high beam functions.
- Feux de croisement: Activate your vehicle's low beam setting for standard illumination.
- Feux de route : Activate your vehicle's high beam setting for increased illumination when conditions permit.
The LED technology provides instant-on illumination and a crisp, clear light output. No special operating procedures are required beyond standard vehicle headlamp opération.
Entretien
The Custom Dynamics ProBEAM LED Headlamp is designed for long-lasting performance with minimal maintenance.
- Nettoyage: Nettoyer la têteamp lens with a soft cloth and mild soap and water. Avoid abrasive cleaners or solvents, as these can damage the lens.
- Inspection: Inspectez périodiquement la têteamp for any signs of damage, loose connections, or moisture ingress.
- Remplacement de l'ampoule : The LED elements are designed to last the lifetime of the product and are not user-replaceable. If the headlamp malfunctions, contact Custom Dynamics support.
Dépannage
| Problème | Cause possible | Solution |
|---|---|---|
| Têteamp n'éclaire pas |
|
|
| Têteamp scintille ou est faible |
|
|
| Humidité à l'intérieur de la lentille |
|
|
Caractéristiques
| Fonctionnalité | Détail |
|---|---|
| Numéro de modèle | PB-575-B |
| Têteamp Taille | 5 3/4 pouces |
| Source de lumière | DIRIGÉ |
| Couleur | Black (housing), Clear (lens) |
| Matériau de la lentille | Polycarbonate |
| Dossier spécial | High Beam functionality |
| Poids de l'article | 2.25 livres |
| Code UPC | 644978545677 |
Garantie et assistance
For warranty information, technical support, or replacement parts, please contact Custom Dynamics directly. Refer to the official Custom Dynamics website for the most current warranty policy and contact details.
Custom Dynamics Contact Information:
- Website: www.customdynamics.com
- Phone: Refer to website pour les numéros de contact actuels.
- Email: Refer to website pour l'adresse e-mail de contact actuelle.
