Manuel d'utilisation du câble audio Radial Catapult MINI TX Cat 5

Introduction

The Radial Catapult MINI TX is a compact and robust 4-channel analog audio snake transmitter designed to send balanced audio signals over a standard Cat 5 or Cat 6 Ethernet cable. This device, when paired with a Catapult MINI RX unit (sold separately), provides a convenient and cost-effective solution for transmitting multiple audio channels over long distances, utilizing existing network infrastructure or dedicated Cat cable runs. Its passive design ensures high-fidelity audio transmission without the need for power.

Radial Catapult MINI TX unit, angled view, showing the blue casing and product name.

Figure 1: Radial Catapult MINI TX unit, angled view, highlighting its compact design and branding.

Caractéristiques principales

4-Channel Audio Transmission: Supports four balanced analog audio signals.
Cat 5/6 Connectivity: Utilizes standard Ethernet cables for signal transmission, offering flexibility and cost savings.
Fonctionnement passif : Requires no external power, simplifying setup and increasing fiabilité.
Conception compacte et durable : Housed in a rugged steel enclosure, suitable for professional use.
XLR and RJ45 Connectors: Standardized connectors for easy integration into existing audio systems.

Instructions d'installation

Setting up the Catapult MINI TX is straightforward. Ensure you have a Catapult MINI RX unit and a shielded Cat 5 or Cat 6 Ethernet cable of appropriate length for your application.

Identifier les composants : Locate the Catapult MINI TX (transmitter) and Catapult MINI RX (receiver) units. The TX unit typically has female XLR inputs, and the RX unit has male XLR outputs.
Connect Audio Sources to TX: Connect your balanced audio sources (e.g., microphones, preamps, mixing console outputs) to the four female XLR inputs on the Catapult MINI TX unit. Each input corresponds to a specific channel.

Radial Catapult MINI TX with four XLR cables connected, showing the input side.

Figure 2: Catapult MINI TX with four XLR cables connected, illustrating the input setup.

Connectez le câble Ethernet : Connect one end of a shielded Cat 5 or Cat 6 Ethernet cable to the RJ45 connector on the Catapult MINI TX unit.

Fin view of Radial Catapult MINI TX showing the RJ45 and XLR connectors.

Figure 3 : Fin view of the Catapult MINI TX, highlighting the RJ45 and XLR connector ports.

Connect RX Unit: Connect the other end of the Ethernet cable to the RJ45 connector on the Catapult MINI RX unit.
Connect Audio Destinations from RX: Connect the male XLR outputs of the Catapult MINI RX unit to your audio destinations (e.g., mixing console inputs, audio interface inputs, powered speakers).
Vérifiez les connexions : Double-check all cable connections to ensure they are secure and correctly routed.

Mode d'emploi

Once the Catapult MINI TX and RX units are connected, operation is automatic due to their passive design. No power or configuration is required.

Flux du signal : Audio signals from your sources connected to the TX unit's XLR inputs will be transmitted over the Cat 5/6 cable to the RX unit, and then output via its XLR connectors.
Mappage des canaux : Each XLR input on the TX unit corresponds directly to an XLR output on the RX unit. Ensure your audio sources and destinations are connected to the correct channels.
Longueur du câble : While Cat 5/6 cables can transmit signals over significant distances, extremely long runs (e.g., hundreds of feet) may introduce slight signal degradation. Test your setup with the intended cable length to ensure optimal performance.
Shielded Cable Requirement: Always use shielded Cat 5 or Cat 6 cable for reliable and noise-free operation. Unshielded cables may introduce interference.

Entretien

The Radial Catapult MINI TX is designed for durability and requires minimal maintenance.

Nettoyage: Utilisez un chiffon doux et sec pour nettoyer l'extérieur de l'appareil. Évitez les nettoyants abrasifs et les solvants.
Stockage: Store the unit in a dry environment, away from extreme temperatures and direct sunlight, when not in use.
Inspection des câbles : Periodically inspect your Cat 5/6 and XLR cables for any signs of wear, damage, or corrosion. Replace damaged cables immediately.
Entretien des connecteurs : Keep the XLR and RJ45 connectors free of dust and debris.

Dépannage

If you encounter issues with your Catapult MINI TX, consider the following troubleshooting steps:

Problème	Cause possible	Solution
Pas de signal audio	Mauvaise connexion du câble Damaged Cat 5/6 cable Unshielded Cat 5/6 cable Câble XLR défectueux Source/destination device issues	Ensure all XLR and RJ45 cables are securely connected. Verify you are using a shielded Cat 5 or Cat 6 cable. Test cables individually with other equipment. Check power and settings of connected audio devices.
Hum or noise in audio	Unshielded Cat 5/6 cable Ground loop issues Interférence électromagnétique externe	Ensure you are using a shielded Cat 5 or Cat 6 cable. Try isolating power supplies of connected equipment. Route Cat cable away from power lines or strong electromagnetic fields.
Signal intermittent	Connexions de câbles desserrées Câble ou connecteur endommagé	Reseat all cables firmly. Inspect cables and connectors for physical damage. Replace if necessary.

Caractéristiques

Fonctionnalité	Détail
Modèle	R800 8028
Chaînes	4 (balanced analog audio)
Connector Type (Audio)	XLR Female (Input)
Connector Type (Data)	RJ45
Exigence de câble	Shielded Cat 5 or Cat 6 Ethernet cable
Opération	Passive (no power required)
Dimensions (L x l x H)	6.3 x 4.3 x 3 pouces (environ)
Poids	1.06 livres (environ)
Matériaux de construction	Acier
Couleur	Bleu

Garantie et assistance

Radial Engineering products are built to high standards and are backed by a limited warranty. For specific warranty terms and conditions, please refer to the official Radial Engineering website or contact their customer support directly. For technical assistance, troubleshooting beyond this manual, or service inquiries, please visit the Radial Engineering support page or contact their authorized service centers.

Officiel Website: www.radialeng.com

	Radial HotShot MD StagGuide d'utilisation du commutateur de microphone électronique Guide d'utilisation du Radial HotShot MD, commetagCe commutateur de microphones est conçu pour le réacheminement momentané de microphones dynamiques vers plusieurs destinations, offrant un contrôle facile pour les chanteurs et la communication au sein du groupe.
	Guide de l'utilisateur de la boîte de direct active Radial J48 Guide d'utilisation complet du boîtier de direct actif Radial J48, détaillant ses caractéristiques, ses fonctions, ses spécifications et les informations relatives à sa garantie pour les applications audio professionnelles.
	Guide d'utilisation du boîtier de direct passif Radial JDI Guide d'utilisation complet du boîtier de direct passif Radial JDI, détaillant ses caractéristiques, ses spécifications, ses applications et le dépannage. Découvrez son transformateur Jensen, son impédance d'entrée/sortie et comment obtenir des performances audio optimales.
	Guide d'utilisation de la tête radiale VT : Guitare Amp Commutation de tête Guide d'utilisation complet du Radial Headbone VT, un appareil permettant aux guitaristes de basculer entre deux lampes ampCe guide couvre les têtes d'amplification et un baffle mono avec commande au pied. Il aborde l'installation, les fonctionnalités, la sécurité et le dépannage.
	Guide d'utilisation du rack Radial Workhorse Powerhouse série 500 Guide d'utilisation du Radial Workhorse Powerhouse, un rack série 500 à 10 emplacements. Ce guide détaille les fonctionnalités, l'installation, le flux du signal, l'alimentation, les spécifications et les informations de garantie destinées aux ingénieurs du son professionnels.
	Préampli Phono Radial J33amp DI User Guide - Enhance Turntable Audio Comprehensive user guide for the Radial J33 Phono Preamp DI. Learn about its features, connections, specifications, and how to integrate your turntable into professional and consumer audio systems.

Radial Engineering R800 8028