Introduction
Thank you for choosing the SILCA Pista Floor Pump. This manual provides essential information for the proper setup, operation, maintenance, and troubleshooting of your new pump. Designed for quick and efficient inflation of bicycle tires, the SILCA Pista combines high-pressure capability with durable construction and premium components.
Produit terminéview
Figure 1: The SILCA Pista Floor Pump in red with a black single-sided base and wood handle.
Caractéristiques principales :
- Conception haute pression : Delivers high pressure for quick and efficient inflation of bicycle tires.
- Construction en acier: Durable steel construction ensures long-lasting quality and performance.
- Wood Handle: Ergonomic Ash wood handle provides a comfortable grip.
- Premium Presta and Schrader Chuck: Equipped with machined aluminum chucks for various valve types.
- Leather Gasket: Includes a leather gasket for a secure and airtight pumping.
Installation
The SILCA Pista Floor Pump comes largely pre-assembled. Follow these steps to prepare your pump for first use:
- Déballage : Retirez délicatement la pompe de son emballage. Vérifiez qu'elle ne présente aucun dommage visible.
- Hose and Chuck Inspection: Ensure the hose is securely attached to the pump body and the chucks (Presta and Schrader) are properly connected to the hose.
- Stabilité de base : Place the pump on a flat, stable surface. The single-sided base provides stability during operation.
Mode d'emploi
Follow these steps for effective and safe tire inflation:
- Prepare the Tire Valve:
- For Presta valves, unscrew the valve core lock nut counter-clockwise until it is loose. Press down briefly on the valve core to release a small amount of air and ensure it is not stuck.
- For Schrader valves, no special preparation is typically needed.
- Fixez le mandrin :
- Select the appropriate chuck (Presta or Schrader).
- Firmly press the chuck onto the tire valve until it is fully seated. Ensure a tight seal to prevent air leakage.
Figure 2: The SILCA Pista Floor Pump chuck attached to a bicycle tire valve.
- Gonflez le pneu :
- Hold the pump handle firmly and place your feet on the pump's base for stability.
- Push the handle down smoothly and completely to inflate the tire. Pull the handle back up to draw in more air.
- Repeat this motion until the desired pressure is reached.
Figure 3: Proper technique for using the SILCA Pista Floor Pump.
- Surveiller la pression :
- Observe the pressure gauge located at the base of the pump. Inflate to the recommended PSI (Pounds per Square Inch) or BAR for your tire.
- Note: The gauge scale is condensed at higher pressures. Read carefully.
Figure 4 : Gros plan view of the pressure gauge on the pump's base.
- Retirez le mandrin : Once the desired pressure is achieved, quickly and firmly pull the chuck straight off the valve.
- Secure Presta Valve (if applicable): For Presta valves, screw the valve core lock nut clockwise until it is finger-tight.
Entretien
Regular maintenance ensures the longevity and optimal performance of your SILCA Pista Floor Pump.
- Leather Gasket Care: The leather gasket is crucial for an airtight seal. Over time, it may dry out or wear.
- If pumping becomes difficult or air leaks are detected, the leather gasket may need lubrication or replacement.
- Apply a small amount of leather conditioner or a suitable lubricant to the gasket to keep it supple.
- Replacement leather gaskets are available from SILCA or authorized dealers.
- Nettoyage général : Essuyez le corps de la pompe et le tuyau avec un chiffon humide.amp chiffon pour enlever la saleté et la poussière. Évitez d'utiliser des produits chimiques agressifs.
- Stockage: Store the pump in a dry, clean environment away from extreme temperatures.
Dépannage
| Problème | Cause possible | Solution |
|---|---|---|
| Pump not building pressure / Air leaking |
|
|
| Gauge not reading correctly or stuck |
|
|
| Pump handle feels loose or detached |
|
|
Caractéristiques
- Nom du modèle : PISTA
- Numéro de pièce : AM-PU-001-ASY-0101
- Couleur: Rouge
- Matériels: Alloy Steel, Aluminum, Brass, Leather, Wood
- Source d'alimentation : Manuel
- Pression maximale : 15 Bars (approximately 220 PSI)
- Dimensions de l'article (L x l x H) : 25.98 x 9.06 x 3.94 pouces
- Dimensions du colis (L x l x H) : 27 x 9.5 x 3 pouces
- Poids du colis : 0.66 kilogrammes
- Code à barres : 853740005886
Garantie et assistance
SILCA products are built for durability and performance. For specific warranty information, please refer to the warranty card included with your purchase or visit the official SILCA website. For technical support, replacement parts, or service inquiries, please contact SILCA customer service directly.
SILCA Official Website: www.silca.cc
Coordonnées: Veuillez vous référer à la website pour les coordonnées les plus récentes.
