Steinbach Active Balls+ Filter System Instruction Manual

Introduction

This manual provides comprehensive instructions for the safe and efficient installation, operation, and maintenance of your Steinbach Active Balls+ Filter System, model 040386. This non-self-priming pump is designed to maintain crystal-clear water in pools up to approximately 19,000 liters. Please read this manual thoroughly before initial use to ensure proper function and longevity of your filter system.

Consignes de sécurité

Respectez toujours les consignes de sécurité suivantes afin d'éviter les blessures ou les dommages :

• Vérifiez que l'alimentation électrique correspond aux spécifications indiquées sur l'étiquette du produit.
• Débranchez l'alimentation électrique avant d'effectuer tout entretien ou nettoyage.
• N’utilisez pas la pompe si le cordon d’alimentation ou la prise est endommagé.
• Tenir les enfants et les personnes non autorisées à l'écart du système de filtration pendant son fonctionnement.
• Install the filter system on a stable, level surface, protected from direct sunlight and rain.
• Do not run the pump dry. Ensure it is always filled with water during operation.
• Maximum water temperature for operation is 35°C (95°F).
• Suitable for saltwater up to a salt content of 5 g/l.

Produit terminéview et composants

The Steinbach Active Balls+ Filter System consists of several key components designed for optimal pool water filtration.

Figure 1 : Plusview of the Steinbach Active Balls+ Filter System components, showing the filter tank, pump unit, and various connection parts.

Figure 2 : Détaillé view of the 7-way valve, indicating various operational modes such as Filter, Rinse, Waste, Recirculate, Closed, and Backwash.

Figure 3: Product label displaying technical specifications of the pump, including model number, power, voltage, and maximum temperature.

Figure 4: The filter system alongside a visual representation of the filter balls, which are the primary filtration medium.

Figure 5: Dimensional diagram illustrating the approximate height of the filter tank, which is 55 cm (22 inches).

Installation

Follow these steps for initial setup of your filter system:

1. Déballer les composants : Retirez soigneusement toutes les pièces de l'emballage. Vérifiez que tous les composants sont présents conformément à la liste de colisage.
2. Positionnez le système : Place the filter system on a firm, level surface near your pool, ensuring it is protected from direct weather exposure.
3. Install Filter Balls: Open the filter tank and carefully pour the approximately 300g of filter balls into the tank. Ensure the central pipe is correctly positioned before closing the tank.
4. Raccordez la pompe au réservoir du filtre : Attach the pump unit to the filter tank using the provided connections. Ensure all seals are properly seated and connections are tightened to prevent leaks. It is recommended to use PTFE tape on threaded connections for a secure seal.
5. Se connecter à la piscine : Connect the pool hoses to the filter system's inlet and outlet ports. The inlet hose typically connects from the pool skimmer/main drain to the pump's suction side, and the outlet hose connects from the filter's return side back to the pool.
6. Remplir d'eau : Before starting the pump, ensure the pool is filled with water and the filter system is primed by allowing water to flow into the pump and filter tank.
7. Connexion électrique : Connect the power plug to a grounded electrical outlet. Ensure the outlet is protected by a Residual Current Device (RCD) for safety.

Operating the 7-Way Valve

The 7-way valve controls the flow of water through the filter system. Always turn off the pump before changing the valve position.

• FILTRE: This is the standard operating position for daily filtration. Water flows from the pool, through the filter balls, and back to the pool.
• REMOUS: Used for cleaning the filter balls. Water flows in reverse through the filter, dislodging trapped debris, and is then directed to waste. Perform backwash when the pressure gauge indicates higher than normal pressure or when water flow decreases.
• RINCER: Used after backwashing to flush out any remaining debris from the filter and settle the filter balls. Water flows through the filter and is directed to waste.
• DÉCHETS: Bypasses the filter and sends water directly from the pool to waste. Useful for vacuuming heavy debris directly to waste or lowering the pool water level.
• RECIRCULER : Circulates water through the pump and back to the pool without passing through the filter. Useful for distributing chemicals quickly.
• FERMÉ: Shuts off all flow to the filter and pump. Use this position only when the pump is off and for maintenance or when the pool is not in use.
• HIVERNAGE : (If applicable) Position for draining the system for winter storage. Consult specific winterization instructions.

Entretien

Regular maintenance ensures optimal performance and extends the life of your filter system.

• Lavage à contre-courant : Perform backwashing regularly, typically once a week or when the pressure gauge reading increases by 0.2-0.3 bar (3-5 psi) above its clean operating pressure.
  1. Éteignez la pompe.
  2. Réglez la vanne à 7 voies sur « RÉTROLAVAGE ».
  3. Mettez la pompe en marche et laissez-la fonctionner jusqu'à ce que l'eau dans le voyant (s'il y en a un) soit claire (environ 2 à 3 minutes).
  4. Éteignez la pompe.
  5. Réglez la vanne à 7 voies sur « RINÇAGE ».
  6. Mettez la pompe en marche et laissez-la fonctionner pendant 30 à 60 secondes.
  7. Éteignez la pompe.
  8. Remettez la vanne à 7 voies sur « FILTRER ».
  9. Mettez la pompe en marche pour reprendre la filtration normale.
• Cleaning Filter Balls: The filter balls can be cleaned manually or in a washing machine (in a laundry bag) at 30°C (86°F) without fabric softener. Replace filter balls when they show signs of significant wear or reduced filtration efficiency.
• Nettoyage du panier de la pompe : Periodically check and clean the pump's pre-filter basket (if applicable) to remove large debris that could obstruct flow.
• Hivérisation: Before freezing temperatures, drain all water from the pump, filter tank, and hoses. Store the pump and valve in a dry, frost-free location.

Dépannage

Consultez cette section pour les problèmes courants et leurs solutions.

Caractéristiques

Garantie et assistance

For warranty information and technical support, please refer to the documentation provided with your purchase or contact Steinbach customer service. Keep your proof of purchase for warranty claims.