1. Introduction
This manual provides essential instructions for the proper setup, operation, and maintenance of your Black Box EVNDVI01-0010 DVI-A to VGA HD15 Cable. Please read this manual thoroughly before using the product to ensure optimal performance and longevity.
2. Produit terminéview
The Black Box EVNDVI01-0010 is a DVI-A to VGA HD15 cable designed to connect a digital DVI-A output from a source device to an analog VGA input on a display device. This cable facilitates the transmission of analog video signals, allowing compatibility between DVI-A enabled devices and traditional VGA monitors or projectors.
Caractéristiques principales :
- Connects digital DVI-A display outputs to analog VGA device inputs.
- Supports resolutions up to 1600 x 1200.
- Features a 17-pin single link configuration for DVI-A.
- Male-to-Male connector gender.
Figure 1: Black Box DVI-A to VGA HD15 Cable. This image displays the cable with its DVI-A (white) and VGA (blue) connectors, illustrating its male-to-male configuration.
3. Installation
Follow these steps to properly connect your DVI-A to VGA cable:
- Identifier les ports : Locate the DVI-A output port on your source device (e.g., computer graphics card) and the VGA input port on your display device (e.g., monitor, projector). The VGA port is typically blue.
- Connect DVI-A: Carefully insert the DVI-A connector of the cable into the DVI-A output port of your source device. Ensure the pins align correctly and gently push until it is fully seated.
- Connecter VGA : Insert the VGA HD15 connector of the cable into the VGA input port of your display device. Tighten the thumbscrews on the VGA connector to secure the connection and prevent accidental disconnections.
- Allumer les appareils : Mettez sous tension à la fois votre périphérique source et votre périphérique d'affichage.
- Sélectionnez Entrée : On your display device, select the correct input source (e.g., 'VGA', 'PC', 'Input 1') using the display's menu or input selection button.
A proper connection should result in the display device showing the video output from the source device.
4. Fonctionnement
Once the Black Box EVNDVI01-0010 cable is correctly connected, its operation is passive. The cable transmits the analog video signal directly from the source to the display. No additional software or drivers are required for the cable itself.
- Paramètres de résolution : Ensure your source device's display settings are configured to a resolution supported by both the source and the display device, up to 1600 x 1200.
- Modes d'affichage: If using a computer, you may need to configure your display mode (e.g., duplicate, extend, second screen only) through your operating system's display settings.
5. Entretien
To ensure the longevity and reliable performance of your Black Box DVI-A to VGA cable, follow these maintenance guidelines:
- À manipuler avec précaution : Évitez de plier brusquement le câble ou d'appliquer une force excessive sur les connecteurs.
- Garder propre: Essuyez régulièrement le câble et les connecteurs avec un chiffon doux et sec pour enlever la poussière et les débris. N’utilisez pas de nettoyants liquides directement sur les connecteurs.
- Conserver correctement : When not in use, coil the cable loosely and store it in a clean, dry environment away from extreme temperatures.
- Inspecter les dommages : Regularly check the cable and connectors for any signs of wear, fraying, or damage. Discontinue use if damage is observed.
6. Dépannage
If you encounter issues with your DVI-A to VGA cable, consider the following troubleshooting steps:
- Aucun signal affiché :
- Assurez-vous que les deux extrémités du câble sont bien connectées.
- Verify that both the source and display devices are powered on.
- Confirm the correct input source is selected on your display device.
- Test with another cable if available to rule out a faulty cable.
- Mauvaise qualité d'image (scintillement, image déformée) :
- Check for loose connections at both ends of the cable. Tighten VGA thumbscrews.
- Adjust the display resolution on your source device to a lower setting to see if the issue resolves.
- Ensure there are no strong electromagnetic interference sources near the cable.
- Inspect the cable for any physical damage.
- Couleurs incorrectes :
- Verify the cable is fully seated and not bent or damaged.
- Check the color settings on your display device and source device.
7. Spécifications
| Marque | Boîte noire |
| Numéro de modèle | EVNDVI01-0010 |
| Type de connecteur | DVI-A Male, VGA HD15 Male |
| Type de câble | DVI-A to VGA |
| Résolution prise en charge | Jusqu'à 1600 x 1200 |
| Connecteur Sexe | Homme à Homme |
| Couleur | Noir, Bleu |
| Poids de l'article | 0.35 kilogrammes (12.3 onces) |
| Utilisation intérieure/extérieure | Intérieur, extérieur |
| Code UPC | 822088058960 |
8. Garantie et assistance
For specific warranty information regarding your Black Box EVNDVI01-0010 DVI-A to VGA HD15 Cable, please refer to the official Black Box webConsultez leur site web ou contactez directement leur service client. Les conditions de garantie peuvent varier.
If you require technical assistance or have questions not covered in this manual, please contact Black Box customer support through their official channels.
