1. Introduction
This manual provides essential instructions for the installation, operation, and maintenance of your Hikvision DS-7732NI-I4/16P-12TB Network Video Recorder (NVR). This NVR is a 32-channel device supporting H.264 and H.265 video compression, resolutions up to 12MP, and features an integrated 16-port Power over Ethernet (PoE) switch. It includes 4 SATA interfaces for storage, with 12TB of pre-installed capacity, and HDMI output for local display.
Please read this manual thoroughly before operating the device and retain it for future reference. Ensure all safety precautions are observed during installation and operation.
Précautions de sécurité
- Utilisez uniquement l'adaptateur secteur spécifié pour cet appareil.
- Assurer une ventilation adéquate pour éviter la surchauffe.
- Évitez d'exposer l'appareil à des liquides ou à des températures extrêmes.
- Ne tentez pas de démonter ou de modifier l'appareil. Confiez toute réparation à un personnel qualifié.
2. Installation
2.1 Déballage et inspection
Carefully unpack the NVR and check the contents against the packing list. Inspect the device for any signs of damage during transit. If any items are missing or damaged, contact your supplier immediately.
2.2 Installation physique
The DS-7732NI-I4/16P-12TB NVR is designed for rack-mounting or desktop placement. Ensure the installation location is stable, well-ventilated, and free from excessive dust or moisture.
Connexion de l'alimentation
- Connect the provided power cable to the NVR's power input and then to a grounded power outlet.
Réseau de connexion
- Connectez un câble Ethernet du port LAN du NVR à votre routeur ou commutateur réseau.
Écran de connexion
- Connect an HDMI cable from the NVR's HDMI output port to a monitor or TV.
Connecting Cameras (PoE)
- Connect IP cameras directly to the NVR's 16 PoE ports using Ethernet cables. The NVR will provide power and data connectivity.
Figure 1: Rear panel connections of the Hikvision DS-7732NI-I4/16P-12TB NVR, illustrating the power input, LAN port, HDMI output, and the 16 PoE ports for camera connections.
Hard Drive Installation (if applicable)
The NVR comes with 12TB pre-installed. If additional drives are needed or replacement is required, follow these steps:
- Mettez le NVR hors tension et débranchez tous les câbles.
- Remove the NVR cover screws and slide off the cover.
- Mount the hard drive(s) into the drive bays using the provided screws.
- Connect the SATA data and power cables to the hard drive(s) and the NVR motherboard.
- Replace the cover and secure the screws.
2.3 Configuration initiale
Powering On and First-Time Wizard
- After connecting all necessary cables, power on the NVR.
- The NVR will boot up and display a first-time setup wizard on the connected monitor.
- Follow the on-screen prompts to set up a strong administrator password, configure network settings (DHCP or static IP), and set the date and time.
Ajout de caméras IP
- The NVR will typically auto-detect Hikvision cameras connected to its PoE ports.
- For manual addition or third-party cameras, navigate to Configuration > IP Camera > Add.
- Enter the camera's IP address, protocol, port, username, and password.
3. Fonctionnement
3.1 Navigation de l'interface utilisateur
The NVR can be accessed via a local monitor, web browser, or client software (e.g., iVMS-4200). The local interface is navigated using a mouse.
Menu principal terminéview
- En direct View: Displays real-time camera feeds.
- Lecture: Accesses recorded footage.
- Configuration: System settings, camera management, recording schedules.
- Événement: Alarm and event management.
- Fermer: Safely powers off or restarts the NVR.
3.2 En direct View
Du direct View screen, you can monitor all connected cameras. Double-click a camera feed to view it in full screen. Use the layout options to display multiple cameras simultaneously (e.g., 4, 9, 16, 32 channels).
Figure 2: The Live View interface of the NVR, displaying multiple camera streams in a grid layout, with options for channel selection and layout customization.
3.3 Enregistrement
To configure recording settings, navigate to Configuration > Enregistrement > Planification.
- Enregistrement continu: Enregistrements constants.
- Enregistrement de détection de mouvement : Enregistre uniquement lorsque du mouvement est détecté.
- Enregistrement d'alarme : Enregistre le déclenchement d'une alarme.
- Enregistrement manuel : Click the record icon in Live View to start/stop recording manually.
3.4 Lecture
Pour accéder aux photos enregistréestage, aller à Lecture depuis le menu principal.
- Select the desired camera(s) and date.
- Use the timeline to navigate through recorded events. Different colors on the timeline indicate different recording types (e.g., continuous, motion).
- Utilisez les commandes de lecture (lecture, pause, avance rapide, retour rapide) pour review footage.
- Pour exporter footage, select the desired segment and click the Agrafe or Exporter bouton.
3.5 Gestion des alarmes
Configure alarm events and responses via Configuration > Événement.
- Détection de mouvement : Define detection areas and sensitivity for each camera.
- Vidéo Tampering: Detects if a camera's view is obstructed or altered.
- Line Crossing/Intrusion Detection: Set up virtual lines or areas to trigger alarms.
- Actions d'alarme : Configure actions such as recording, sending email notifications, triggering alarm outputs, or sounding a buzzer.
3.6 Paramètres du système
Access various system settings via Configuration > System.
- Général: Date and time, language.
- Gestion des utilisateurs : Create, modify, or delete user accounts and assign permissions.
- Stockage: View HDD status, format drives, configure overwrite settings.
- Réseau: Adjust IP address, DNS, port settings.
4. Entretien
4.1 mises à jour du micrologiciel
Regularly check for firmware updates on the official Hikvision webLe site web indique que les mises à jour du micrologiciel peuvent apporter de nouvelles fonctionnalités, des améliorations de performances et des améliorations de sécurité.
- Téléchargez le bon firmware file pour votre modèle de NVR.
- Transfer the firmware to a USB drive.
- Accéder à Configuration > System > Maintenance > Upgrade et suivez les instructions à l'écran.
- Do not power off the NVR during the upgrade process.
4.2 Gestion du disque dur
Monitor the health of your hard drives via Configuration > Stockage > Disque dur. If a drive shows errors or fails, replace it promptly. You can also format drives from this menu.
4.3 Sauvegarde et restauration du système
It is recommended to regularly back up your NVR's configuration settings. This can be done via Configuration > System > Maintenance > Import/Export. You can export the configuration to a USB drive and restore it if needed.
4.4 Nettoyage
Periodically clean the NVR's exterior with a soft, dry cloth. Ensure ventilation openings are free from dust to maintain proper airflow and prevent overheating.
5. Dépannage
This section addresses common issues you might encounter. For more complex problems, refer to the Hikvision support website ou contactez le support technique.
| Problème | Cause possible | Solution |
|---|---|---|
| NVR does not power on | Câble d'alimentation débranché ; alimentation électrique défectueuse ; problème de prise électrique. | Check power cable connection; test power outlet; contact support if power supply is suspected faulty. |
| Aucun affichage vidéo sur le moniteur | HDMI cable loose/faulty; incorrect monitor input; NVR resolution mismatch. | Check HDMI cable; ensure monitor is on correct input; try a different monitor or cable; access NVR via web interface to adjust resolution. |
| Cameras not connecting/displaying | PoE cable issue; camera faulty; incorrect camera IP/credentials; network conflict. | Check PoE cable connections; verify camera power; ensure camera IP is correct and not conflicting; check camera status in NVR configuration. |
| Aucun enregistrement | Hard drive full/faulty; recording schedule not set; camera not added/enabled. | Check HDD status and capacity; configure recording schedule; ensure cameras are added and enabled for recording. |
| Cannot access NVR via network | Incorrect IP address/gateway; network cable issue; firewall blocking access. | Verify NVR's IP address and gateway; check network cable; temporarily disable firewall for testing; ensure NVR and PC are on the same subnet. |
6. Spécifications
The following table outlines the key technical specifications for the Hikvision DS-7732NI-I4/16P-12TB NVR.
| Fonctionnalité | Spécification |
|---|---|
| Modèle | DS-7732NI-I4/16P-12TB |
| Entrée vidéo | 32 canaux |
| Compression vidéo | H.265 + / H.265 / H.264 + / H.264 |
| Résolution d'enregistrement maximale | Jusqu'à 12 MP |
| Ports PoE | 16 interfaces réseau PoE indépendantes |
| Interfaces SATA | 4 interfaces SATA pour 4 disques durs |
| Pre-installed Storage | 12 To (extensible) |
| Sortie vidéo | 1 HDMI, 1 VGA |
| Dimensions (L x P x H) | 15.4 x 17.5 x 2.8 pouces (390 x 445 x 70 mm) |
| Poids (sans les disques durs) | 11.02 livres (5 kg) |
| Fabricant | Hikvision États-Unis |
7. Garantie et assistance
7.1 Informations sur la garantie
For specific warranty terms and conditions applicable to your Hikvision DS-7732NI-I4/16P-12TB NVR, please refer to the warranty card included with your product or the official Hikvision website. La garantie couvre généralement les défauts de matériaux et de fabrication dans des conditions normales d'utilisation.
7.2 Assistance technique
Should you require technical assistance, please visit the official Hikvision support website. You can find comprehensive FAQs, troubleshooting guides, software downloads, and contact information for technical support. When contacting support, please have your NVR model number (DS-7732NI-I4/16P-12TB) and serial number readily available.
Official Hikvision Support: https://www.hikvision.com/us/support/
