1. Produit terminéview
The Genie Stinger 390GED21V is a visor-sized remote control designed for compatibility with Genie garage door openers and receivers. It operates on a 390 MHz frequency and utilizes 12 dip switches for secure coding. This remote features a test/operate LED light and is powered by a 12-volt long-life battery.
Figure 1 : Genie Stinger 390GED21V Garage Door Opener Remote. This image displays the compact, black remote control with a beige button, designed to clip onto a vehicle's sun visor.
2. Installation et programmation
2.1 Installation de la batterie
The remote comes with a pre-installed 12V A23 battery. If replacement is needed:
- Ouvrez soigneusement la télécommande casing, typically by sliding the back cover or gently prying it open at a designated notch.
- Remove the old 12V A23 battery.
- Insert the new 12V A23 battery, ensuring the positive (+) and negative (-) terminals are correctly aligned.
- Fermez la télécommande casing en toute sécurité.
2.2 Réglage des commutateurs DIP
The 390GED21V remote uses 12 dip switches to match the code of your existing Genie garage door opener or receiver. This ensures secure and unique operation.
- Locate the dip switches inside your existing working garage door remote or on the garage door opener unit itself. These are typically small switches labeled 1 through 12.
- Ouvrez le casing of your new Stinger 390GED21V remote to expose its 12 dip switches.
- Carefully match the position (ON/OFF or +/0/-) of each dip switch on your new remote to the corresponding switch on your existing remote or opener unit. Ensure an exact match for all 12 switches.
- Once all switches are set, close the remote casing.
2.3 Testing the Remote
After setting the dip switches, test the remote's functionality:
- Stand within a reasonable range of your garage door opener.
- Press the button on the Stinger 390GED21V remote.
- Observe if the garage door responds (opens or closes). The remote's test/operate LED light should illuminate when the button is pressed.
- If the door does not respond, re-check the dip switch settings and battery installation.
3. Mode d'emploi
To operate your garage door using the Stinger 390GED21V remote:
- Ensure you are within range of your garage door opener.
- Appuyez sur le bouton unique de la télécommande et relâchez-le.
- The garage door will either open or close, depending on its current state.
- The remote's LED light will illuminate briefly when the button is pressed, indicating that a signal is being transmitted.
4. Entretien
4.1 Remplacement de la batterie
Replace the 12V A23 battery when the remote's range decreases significantly or the LED light fails to illuminate when the button is pressed. Refer to Section 2.1 for battery installation steps.
4.2 Nettoyage
Clean the remote with a soft, dry cloth. Avoid using harsh chemicals or abrasive cleaners, as these can damage the casing ou composants internes.
5. Dépannage
- La télécommande ne fonctionne pas :
- Check battery: Ensure the 12V A23 battery is correctly installed and not depleted. Replace if necessary.
- Verify dip switches: Confirm that all 12 dip switches are set to match your garage door opener's code exactly.
- Range: Ensure you are within the operational range of the garage door opener.
- Portée opérationnelle courte :
- Low battery: Replace the 12V A23 battery.
- Interference: Check for potential sources of radio frequency interference near your garage door opener or remote.
- Voyant LED non allumé :
- Battery issue: The battery may be dead or incorrectly installed. Replace or re-install.
- Remote malfunction: If battery and dip switch settings are correct, the remote may require replacement.
6. Spécifications
| Numéro de modèle | 390GED21V |
| Fréquence | 390 MHz |
| Compatibilité | Genie transmitters and receivers |
| Codage | 12 commutateurs DIP |
| Type de batterie | 12V A23 (included) |
| Indicateur | Test/Operate LED Light |
| Matériel | Plastique |
| Couleur | Black case, Beige button |
| Dimensions (environ) | 4 x 2 x 2 pouces |
| Poids (environ) | 4 onces |
7. Informations sur la garantie
Specific warranty details for the Genie Stinger 390GED21V remote are not provided in this manual. For information regarding product warranty, please refer to the manufacturer's official webConsultez le site ou contactez le détaillant auprès duquel le produit a été acheté.
8. Assistance
If you encounter issues not covered in this manual or require further assistance, please visit the official Genie support webConsultez leur site web ou contactez leur service client. Les coordonnées se trouvent généralement sur l'emballage du produit ou sur le site du fabricant. website.
