Introduction
This manual provides essential instructions for the installation, operation, and maintenance of the Sensor Switch NPODM-2P-DX-WH nLight WallPod Switch. This device is a low-voltage, two-channel push-button wall switch designed for On/Off control and dimming (Raise/Lower) within an nLight lighting control system. Please read this manual thoroughly before installation and use to ensure proper function and safety.
Consignes de sécurité
- AVERTISSEMENT: Risk of electric shock. Installation should only be performed by a qualified electrician in accordance with all national and local electrical codes.
- Coupez l'alimentation au niveau du disjoncteur avant d'installer ou d'entretenir l'interrupteur.
- Ne pas installer en milieu humide ou damp emplacements.
- Assurez-vous que toutes les connexions de câblage sont sécurisées et correctement isolées.
- Cet appareil est conçu pour les basses tensionstage applications. Do not connect to line voltage.
Configuration et installation
The NPODM-2P-DX-WH is designed for wall-mount installation. Follow these general steps for proper setup:
- Coupure de courant : Before beginning any installation, ensure that power to the circuit is turned off at the main circuit breaker.
- Montage: The switch is designed to be wall-mounted. Secure the device to a standard electrical box using the provided screws and mounting brackets.
- Câblage : Connectez le bas-voltage wiring to the screw terminals on the back of the switch. Refer to the nLight system documentation for specific wiring diagrams and connections. Ensure proper polarity and secure connections.
- Installation de la façade : Once the switch is securely mounted and wired, attach the decorative faceplate (not included) to complete the installation.
- Restauration de puissance : Rétablir le courant au disjoncteur.
Mode d'emploi
The NPODM-2P-DX-WH features two channels for control, typically configured for On/Off and dimming functions. The control method is touch-based via push buttons.
- Contrôle marche / arrêt: Press the designated On/Off button to toggle the connected lighting circuit between on and off states.
- Dimming (Raise/Lower): Use the dedicated Raise and Lower buttons to adjust the light output level. Press and hold the 'Raise' button to increase brightness, and press and hold the 'Lower' button to decrease brightness.
- nLight System Integration: This WallPod operates as part of an nLight lighting control system. Its functionality and configuration are managed through the nLight network, often utilizing Wi-Fi connectivity for system communication.
Entretien
The Sensor Switch NPODM-2P-DX-WH requires minimal maintenance.
- Nettoyage: To clean the plastic surface, gently wipe with a soft, damp Chiffon. N’utilisez pas de nettoyants abrasifs, de solvants ou de produits chimiques agressifs, car ils pourraient endommager la finition.
- Inspection: Inspectez régulièrement l'interrupteur afin de détecter tout dommage visible ou tout mauvais contact. En cas de problème, coupez l'alimentation et consultez un électricien qualifié.
Dépannage
If you experience issues with your NPODM-2P-DX-WH switch, consider the following common troubleshooting steps:
- Aucune réponse du commutateur :
- Check if the circuit breaker supplying power to the switch is on.
- Verify that all low-voltage wiring connections are secure and correct.
- Ensure the switch is properly integrated into the nLight system and configured.
- Dimming Not Functioning:
- Confirm that the connected lighting fixtures are dimmable.
- Check nLight system settings to ensure dimming functionality is enabled and correctly assigned to the switch.
- Fonctionnement intermittent :
- Vérifiez le câblage pour détecter les connexions desserrées ou endommagées.
- Check for potential interference with the Wi-Fi connectivity if applicable to the nLight system.
If problems persist after attempting these steps, contact a qualified electrician or the manufacturer's technical support.
Caractéristiques
| Fonctionnalité | Détail |
|---|---|
| Modèle | NPODM-2P-DX-WH |
| Marque | Interrupteur à capteur |
| Type de commutateur | Dimmer Switch, Push Button |
| Mode de fonctionnement | Off (as a default state, controls On/Off and Dimming) |
| Type de contact | Normalement ouvert |
| Type de connecteur | Bornes à vis |
| Terminal | Trou traversant |
| Matériel | Plastic (housing), Metal (contact) |
| Dimensions de l'article (L x l x H) | 5.12 x 3.46 x 2.28 pouces |
| Type de circuit | 2 voies |
| Type de montage | Support mural |
| Type d'actionneur | Bouton poussoir |
| Nombre de postes | 2 (canaux) |
| Type de contrôleur | Bouton poussoir |
| Méthode de contrôle | Touche |
| Protocole de connectivité | Wi-Fi (for nLight system integration) |
| Quoitage | 250 watts (maximum load capacity) |
| Couleur | White (product variant) |
| Poids de l'article | 0.29 livres |
| Évaluation de la protection internationale | IP54 |
| Spécification satisfaite | UL, cUL, IP54 |
| Code UPC | 745977911958 |
Informations sur la garantie
According to product information, this Sensor Switch NPODM-2P-DX-WH is sold with Aucune garantie. Please verify warranty terms with your point of purchase or the manufacturer directly for the most current information.
Soutien
For technical assistance, further product information, or to report issues not covered in this manual, please contact Sensor Switch customer support or visit their official website. Always provide your product model number (NPODM-2P-DX-WH) when seeking support.
