Introduction
This manual provides essential information for the safe and efficient use of your Philips Lighting ER55LD3WR LED Exit Sign. Please read these instructions carefully before installation and operation, and retain them for future reference. This product is designed for commercial lighting applications, specifically as a lighted exit sign.
Consignes de sécurité
- Always disconnect power before installing or servicing the unit.
- L'installation doit être effectuée par un électricien qualifié, conformément aux normes électriques nationales et locales.
- N'utilisez pas ce produit à des fins autres que l'utilisation prévue.
- Assurez-vous que toutes les connexions sont sécurisées et correctement isolées.
- Tenir à l’écart de l’eau et de l’humidité excessive.
Contenu du colis
Vérifiez que tous les composants sont présents avant de commencer l'installation :
- Philips Lighting ER55LD3WR LED Exit Sign unit
- Matériel de montage (vis, chevilles)
- Manuel d'instructions (ce document)
Configuration et installation
The Philips Lighting ER55LD3WR LED Exit Sign is designed for wall mounting. Ensure the mounting surface is suitable to support the weight of the unit.
- Préparez la zone d'installation : Disconnect power to the circuit where the exit sign will be installed.
- Montage:
- Identify the desired wall mounting location.
- Use the provided mounting hardware to securely attach the exit sign to the wall. Ensure the unit is level.
- Câblage :
- Connect the building's 120V AC power supply to the corresponding wires on the exit sign. Refer to the wiring diagram inside the unit's housing for specific connections.
- Assurez une bonne mise à la terre.
- Connect the internal battery (if not pre-connected). This is crucial for emergency operation.
- Assemblage final : Secure any covers or diffusers.
Figure 1 : Face avant view of the Philips Lighting ER55LD3WR LED Exit Sign. This image shows the white housing with the red "EXIT" lettering illuminated, indicating its primary function as an emergency egress indicator.
Mode d'emploi
Once installed and power is restored, the Philips Lighting ER55LD3WR LED Exit Sign will operate automatically.
- Fonctionnement normal : When AC power is present, the "EXIT" sign will be illuminated by the internal LEDs. The green indicator light on the unit will be ON, signifying operating status.
- Opération d'urgence: In the event of an AC power failure, the unit will automatically switch to battery backup, illuminating the "EXIT" sign for a specified duration (typically 90 minutes).
- Bouton de test : A test button is provided on the unit to verify emergency operation. Press and hold the "Push to Test" button to simulate an AC power failure. The sign should remain illuminated, and the green indicator light will blink, indicating testing. Release the button to return to normal operation.
Figure 2 : Gros plan view of the test button and indicator lights on the Philips Lighting ER55LD3WR LED Exit Sign. The green indicator shows operating status (ON for ready, Blinking for testing). The red indicator shows service alerts such as battery, charger board, transformer, or LED strip faults.
Entretien
Regular maintenance ensures the reliability and longevity of your LED Exit Sign.
- Test mensuel : Press the "Push to Test" button for at least 30 seconds to ensure the battery backup system is functioning. The sign should remain illuminated.
- Test annuel : Disconnect AC power to the unit for 90 minutes to verify the battery can sustain emergency illumination for the required duration.
- Nettoyage: Nettoyez l'extérieur de l'appareil avec un chiffon doux.amp chiffon. N'utilisez pas de nettoyants abrasifs ou de solvants.
- Remplacement de la batterie : The internal battery has a limited lifespan. If the unit fails to hold a charge or the red "Battery fault" indicator illuminates, the battery may need replacement. Contact qualified service personnel for battery replacement.
Dépannage
Consultez le tableau suivant pour connaître les problèmes courants et leurs solutions.
| Problème | Cause possible | Solution |
|---|---|---|
| Sign does not illuminate (AC power present) | No AC power; faulty wiring; LED strip fault | Check circuit breaker; verify wiring connections; contact service for LED replacement. |
| Sign does not illuminate during power outage (emergency mode) | Battery not connected; discharged battery; faulty battery; charger board fault | Ensure battery is connected; allow 24 hours for initial charge; replace battery; contact service for charger board repair. |
| Red Service Alert indicator is ON | Indicates battery, charger board, transformer, or LED strip fault (refer to unit label) | Identify specific fault from unit label; perform monthly/annual tests; contact qualified service personnel. |
| Green Operating Status indicator is OFF (AC power present) | No AC power; internal fault | Check AC power supply; contact qualified service personnel. |
Caractéristiques
| Fonctionnalité | Détail |
|---|---|
| Numéro de modèle | ER55LD3WR |
| Marque | Éclairage Philips |
| Type de source lumineuse | DIRIGÉ |
| Voltage | 120 volts |
| Source d'énergie | Électrique avec fil |
| Type de montage | Support mural |
| Matériel | Métal |
| Couleur | Blanc |
| Dimensions du produit | 4.25 x 6.25 x 4.8 pouces |
| Poids de l'article | 4.98 livres |
| Code UPC | 781370410117 |
Garantie et assistance
For warranty information or technical support, please contact Philips Lighting customer service. Keep your purchase receipt as proof of purchase.
Fabricant: Éclairage Philips
Website: Visit the PHILIPS Store on Amazon
