Manuel d'utilisation de l'interface homme-machine graphique MT8100iE Weintek 10.2 pouces

1. Introduction

The Weintek MT8100iE is a 10.2-inch Human Machine Interface (HMI) designed for industrial automation applications. It features an 800 x 480 TFT industrial-grade LCD and is built to fully support major PLCs such as Rockwell, Siemens, Mitsubishi, and Omron. This manual provides essential information for the proper installation, operation, and maintenance of your MT8100iE HMI.

2. Consignes de sécurité

Please read and understand all safety instructions before operating the device. Failure to comply may result in injury or damage to the equipment.

• Assurez-vous que l'alimentation électrique est débranchée avant toute installation ou maintenance.
• Seul un personnel qualifié est habilité à installer et à entretenir cet équipement.
• Do not expose the device to excessive moisture, dust, or extreme temperatures.
• Verify correct wiring and connections to prevent electrical hazards.
• The front panel is NEMA4/IP65 compliant, but ensure proper sealing during installation to maintain this rating.

3. Contenu du colis

Vérifiez que tous les éléments sont présents dans le colis :

• MT8100iE HMI Unit
• Supports de montage (4x)
• Connecteur d'alimentation
• Manuel de l'utilisateur (ce document)
• CD-ROM with EasyBuilder Pro Software (or download link)

4. Produit terminéview

Familiarize yourself with the components and interfaces of the MT8100iE HMI.

4.1 avant View

Figure 4.1 : Face avant view of the MT8100iE HMI, showing the 10.2-inch TFT LCD touchscreen and the power indicator LED at the top left.

4.2 Côté View

Figure 4.2 : Côté profile of the MT8100iE, illustrating its compact form factor suitable for panel mounting.

4.3 Arrière View

Figure 4.3 : Arrière view of the MT8100iE, highlighting the mounting holes for panel installation, the fuse holder for power protection, and the system reset button.

4.4 Ports de communication

Figure 4.4 : Bas view of the MT8100iE, detailing the various communication ports including USB, Ethernet, COM1 (RS-232), and COM2 (RS-485 2W/4W).

5. Installation

5.1 Montage sur panneau

1. Cut an opening in the control panel according to the dimensions provided in the installation guide (refer to the separate installation template for precise measurements).
2. Insert the MT8100iE HMI into the cutout from the front.
3. From the rear of the panel, insert the four mounting brackets into the slots on the HMI unit.
4. Tighten the screws on the mounting brackets evenly until the HMI is securely fastened to the panel. Do not overtighten.

5.2 Connexion d'alimentation

• Connect a 24V DC power supply to the power input terminal block on the rear of the HMI.
• Assurez-vous de respecter la polarité (+ et -).
• Secure the connection firmly.

5.3 Connexions de communication

• Ports série: Use the COM1 (RS-232) and COM2 (RS-485 2W/4W) ports to connect to PLCs or other serial devices. Refer to your PLC's documentation for specific wiring diagrams.
• Port Ethernet: Connect an Ethernet cable to the RJ45 port for network communication with PLCs or for remote access.
• Ports USB : Use the USB host ports for connecting USB flash drives for project transfers or other peripherals.

6. Mode d'emploi

6.1 Mise sous tension

Once all connections are secure, apply power to the HMI. The power indicator LED will illuminate, and the HMI will boot up, displaying the configured project.

6.2 Téléchargement du projet

To load a new project or update an existing one:

1. Create or modify your HMI project using the EasyBuilder Pro software on a PC.
2. Connect the PC to the HMI via Ethernet or USB.
3. In EasyBuilder Pro, use the 'Download' function to transfer the project to the HMI.
4. The HMI will restart with the new project loaded.

6.3 Fonctionnement de l'écran tactile

The MT8100iE features a resistive touchscreen. Use your finger or a non-sharp stylus to interact with the on-screen elements such as buttons, input fields, and displays.

6.4 PLC Communication

The HMI is designed to communicate with various PLCs. Ensure the communication settings (protocol, baud rate, station ID, etc.) configured in your EasyBuilder Pro project match those of your connected PLC.

7. Entretien

Regular maintenance ensures optimal performance and longevity of your HMI.

• Nettoyage: Utilisez un chiffon doux et sec.amp chiffon pour nettoyer l'écran et casing. Do not use abrasive cleaners or solvents. Ensure no liquid enters the device.
• Mises à jour du micrologiciel : Periodically check the Weintek website for firmware updates to ensure your HMI has the latest features and bug fixes.
• Remplacement du fusible : If the HMI does not power on, check the fuse located on the rear panel. Replace it with a fuse of the same type and rating if necessary. Always disconnect power before replacing the fuse.
• Conditions environnementales : Veillez à ce que l'environnement d'exploitation reste dans les plages de température et d'humidité spécifiées afin d'éviter tout dommage.

8. Dépannage

Cette section propose des solutions aux problèmes courants que vous pourriez rencontrer.

9. Spécifications

10. Garantie et assistance

Weintek products are manufactured to high quality standards. For warranty information and technical support, please refer to the official Weintek website or contact your authorized distributor. Keep your purchase receipt as proof of purchase for warranty claims.

For software downloads, drivers, and additional resources, visit the official Weintek support portal.