Introduction
This manual provides essential instructions for the safe and efficient operation of your Pro-Ject Pre Box RS Stereo Preamplifier. Please read this manual thoroughly before using the device and retain it for future reference. The Pro-Ject Pre Box RS is a high-fidelity stereo preamplifier designed to provide precise signal amplification and versatile connectivity options for your audio system.
Consignes de sécurité
- Assurer l'alimentation voltage correspond aux exigences spécifiées sur l'unité.
- N'exposez pas l'appareil à la pluie ou à l'humidité.
- Évitez de placer l’appareil à proximité de sources de chaleur ou en plein soleil.
- N'ouvrez pas le casing. Confiez toutes les interventions de maintenance à un personnel qualifié.
- Disconnect the power cord from the outlet if the unit will not be used for an extended period.
Installation
1. Déballage
Retirez délicatement le préamplifier from its packaging. Check for any signs of damage during transit. Keep the original packaging for potential future transport or servicing.
2. Connexion des sources et sorties audio
The rear panel of the Pre Box RS offers a variety of input and output options for connecting your audio components. Refer to the image below for a visual guide to the connections.
Image 1 : Connexions du panneau arrière. This image displays the rear panel of the Pro-Ject Pre Box RS preamplifier. Visible connections include RCA inputs (In 1, In 2, In 3), XLR inputs (In 4 L/R, In 5 L/R, In 6 L/R), RCA outputs (Out R, Pre Out R, Out L, Pre Out L), and the 18V power input. The serial number and manufacturer information are also visible.
- Entrées : Connect your audio sources (e.g., CD player, streamer, phono stage) to the available RCA inputs (In 1, In 2, In 3) or XLR inputs (In 4 L/R, In 5 L/R, In 6 L/R). Ensure correct left and right channel connections.
- Résultats : Connectez le préamplifier's outputs to your power amplifier or active speakers. The unit provides both RCA (Out R, Out L) and XLR (Pre Out R, Pre Out L) outputs for flexible integration into your audio system.
3. Connexion électrique
Connect the supplied 18V DC power adapter to the 'Power 18V' input on the rear panel of the preamplifier. Then, plug the power adapter into a suitable wall outlet. Ensure all audio connections are secure before powering on the unit.
Mode d'emploi
1. Mise sous/hors tension
Locate the power button on the front panel of the Pre Box RS. Press it once to power on the unit. Press it again to power off. Allow a few seconds for the unit to stabilize after powering on.
2. Sélection d'entrée
Use the input selector on the front panel to choose your desired audio source. Cycle through the available inputs (In 1, In 2, In 3, In 4, In 5, In 6) until the active source is selected.
3. Contrôle du volume
Adjust the volume using the dedicated volume knob on the front panel. Start with a low volume setting and gradually increase it to a comfortable listening level.
4. Tube Output Stage
The Pre Box RS features a tube output stage. This can typically be engaged or disengaged via a switch on the front panel. Experiment with both modes to find your preferred sound signature, as the tube stage introduces a characteristic warmth and realism to the audio.
Entretien
Nettoyage
Disconnect the preamplifier from the power supply before cleaning. Use a soft, dry cloth to wipe the exterior surfaces. Do not use liquid cleaners or abrasive materials, as they may damage the finish.
Remplacement des tubes
The tubes in the Pre Box RS have a finite lifespan. If you notice a degradation in sound quality or unusual noise, the tubes may need replacement. This procedure should only be performed by qualified service personnel or by following specific instructions provided by Pro-Ject. Contact your dealer or Pro-Ject support for guidance on tube replacement.
Dépannage
| Problème | Cause possible | Solution |
|---|---|---|
| Pas de courant | Câble d'alimentation non branché ; prise de courant défectueuse. | Vérifiez le branchement du câble d'alimentation ; essayez une autre prise. |
| Pas de son | Incorrect input selected; cables loose; power amplifier éteint. | Select correct input; check all audio cable connections; ensure power amplifier est allumé. |
| Son déformé | Input signal too high; faulty cables; damaged tubes. | Reduce source volume; replace cables; consult service for tube inspection. |
| Bruit de bourdonnement ou de bourdonnement | Ground loop; faulty cables; proximity to interference sources. | Ensure proper grounding; try different cables; move unit away from other electronics. |
Caractéristiques
- Numéro de modèle : 13184
- Dimensions du produit : 15.59 x 13.31 x 7.32 pouces
- Poids de l'article : 8 livres
- Fabricant: Projet
- ASIN: B00AE7YTTW
- Date de mise en ligne sur Amazon : 5 décembre 2012
Garantie et assistance
For warranty information and technical support, please refer to the documentation provided with your purchase or visit the official Pro-Ject Audio Systems website. Contact your authorized Pro-Ject dealer for service or assistance.
Pro-Ject Audio Systems: www.project-audio.com
