Introduction
This manual provides comprehensive instructions for the assembly, operation, maintenance, and troubleshooting of your Teknetics T2LTD-BLK Special Edition Metal Detector. Please read this manual thoroughly before using the device to ensure optimal performance and longevity.
The Teknetics T2LTD-BLK is designed for advanced metal detection, offering exceptional depth and speed for coin shooting and relic hunting. It features dual DD search coils (5-inch and 11-inch) and trigger-actuated pinpointing for precise target location.
Informations importantes sur la sécurité
- Always exercise caution when digging to avoid underground utilities or hazardous objects.
- N’utilisez pas le détecteur pendant les orages ou par conditions météorologiques extrêmes.
- Keep the control housing dry. The search coils are waterproof, but the control housing is not.
- Utilisez uniquement les piles recommandées.
- This device is heavy and may cause strain or injury if not handled properly. Maintain proper posture and take breaks during extended use.
Composants du produit
Your Teknetics T2LTD-BLK package includes the following main components:
- Control Housing with Display
- Tige supérieure
- Tige inférieure
- Accoudoir
- 11-inch DD Waterproof Search Coil
- 5-inch DD Waterproof Search Coil
- Coil Mounting Bolt and Washers
Image: Teknetics T2LTD-BLK Metal Detector with both 5-inch and 11-inch DD coils. This image shows the complete metal detector assembly, including the control unit, shaft, armrest, and both the larger 11-inch DD search coil and the smaller 5-inch DD search coil.
Configuration et assemblage
- Fixez la bobine de recherche :
Secure the desired search coil (11-inch or 5-inch DD) to the lower stem using the provided non-metallic bolt and washers. Ensure it is snug but do not overtighten.
- Assemble the Stems:
Insert the lower stem into the upper stem. Adjust the length to a comfortable position for your height, ensuring the search coil is parallel to the ground when held naturally.
- Monter le boîtier de commande :
Slide the control housing onto the upper stem. The armrest should be positioned to support your forearm comfortably.
- Connectez le câble de la bobine :
Wrap the search coil cable securely around the stem, leaving enough slack for coil movement. Plug the connector into the receptacle on the control housing. Ensure the connection is firm.
- Installer les piles :
The T2LTD-BLK requires 4 AA batteries. Open the battery compartment on the control housing and insert the batteries, observing proper polarity. Close the compartment securely.
Image : Gros plan view of the Teknetics T2LTD-BLK control panel. This image highlights the digital display, showing target ID, sensitivity, discrimination settings, and battery indicator. The control knob and menu button are also visible.
Mode d'emploi
Marche/Arrêt
To power on the detector, press and hold the MENU button. To power off, press and hold the MENU button again until the display turns off.
Modes de fonctionnement de base
- Mode Métal intégral : Detects all types of metal. Ideal for finding deeply buried targets or when the target material is unknown.
- Mode de discrimination : Allows the user to filter out unwanted metals (e.g., iron) and focus on specific target types.
Paramètres clés
- Sensibilité: Adjusts the detector's ability to detect targets. Higher sensitivity increases depth but can also increase false signals in mineralized ground.
- Discrimination Level: Sets the rejection level for unwanted metals. Higher levels reject more ferrous items.
- Équilibre au sol : Essential for stable operation in mineralized soil. The T2LTD-BLK features manual ground balance. Refer to the detailed manual for specific ground balancing procedures.
- Nombre de tonalités : Selects the audio tone response for different target IDs.
Trigger-Actuated Pinpointing
To pinpoint a target, center the search coil over the detected object. Pull and hold the trigger located under the control housing. Slowly move the coil in a cross-pattern over the target. The audio tone will peak, and the target ID will stabilize when the coil is directly over the center of the object.
Entretien et soins
- Nettoyage: Essuyez le détecteur avec de l'eau.amp Essuyez le chiffon après chaque utilisation. N’utilisez pas de nettoyants abrasifs ni de solvants.
- Stockage: Rangez le détecteur dans un endroit sec et frais. Retirez les piles si vous prévoyez de le ranger pendant une période prolongée afin d'éviter les fuites.
- Entretien des serpentins : The search coils are waterproof and can be rinsed with fresh water. Ensure the coil cable connection to the control housing remains dry.
- Remplacement de la batterie : Remplacez les piles lorsque le voyant de batterie faible s'affiche.
Dépannage
| Problème | Cause possible | Solution |
|---|---|---|
| Pas de courant | Piles mortes ou mal installées | Remplacez les piles, vérifiez la polarité. |
| Erratic signals/False signals | High sensitivity, poor ground balance, electromagnetic interference (EMI) | Reduce sensitivity, re-ground balance, move away from power lines or other electronics. |
| Aucun son cible | Volume too low, headphones unplugged/faulty | Increase volume, check headphone connection, try different headphones. |
| Détection de profondeur médiocre | Faible sensibilité, équilibre du sol incorrect, sol fortement minéralisé | Increase sensitivity, re-ground balance, consider using a smaller coil in highly mineralized areas. |
Caractéristiques
| Fonctionnalité | Détail |
|---|---|
| Modèle | T2LTD-BLK (T2 Special Edition) |
| Fréquence de fonctionnement | 13 kHz |
| Rechercher des bobines | 11-inch DD Waterproof, 5-inch DD Waterproof |
| Source d'énergie | 4 piles AA |
| Autonomie de la batterie | Environ 30 heures |
| Poids | 4.1 livres (1.86 kg) |
| Longueur réglable | Oui |
| Évaluation de la protection internationale | IP54 (Boîtier de commande non étanche) |
| Utilisation recommandée | Coin Shooting, Relic Hunting |
Informations sur la garantie
Teknetics products are backed by a manufacturer's warranty. For specific warranty terms and conditions, please refer to the documentation included with your purchase or visit the official Teknetics webConsultez le site. Conservez votre preuve d'achat pour toute réclamation au titre de la garantie.
Assistance clientèle
For technical assistance, troubleshooting beyond this manual, or spare parts, please contact Teknetics customer support. You can find contact information on the official Teknetics websur le site ou auprès de votre revendeur agréé.
Official Teknetics Website: Teknetics Store on Amazon
