Manuel d'utilisation du casque sans fil UHF Thomson WHP3001BK

1. Introduction

This manual provides comprehensive instructions for the setup, operation, maintenance, and troubleshooting of your Thomson WHP3001BK UHF Wireless Headphones. Please read this manual thoroughly before using the product to ensure proper function and longevity.

2. Consignes de sécurité

• Do not expose the headphones or transmitter to rain, moisture, or extreme temperatures.
• Évitez de laisser tomber ou de soumettre l'appareil à des impacts violents.
• Ne tentez pas de démonter ni de modifier l'appareil. Confiez toute réparation à un personnel qualifié.
• Keep the product away from medical devices that may be affected by radio waves.
• Jetez les piles de manière responsable, conformément à la réglementation locale.
• Une écoute prolongée à des niveaux de volume élevés peut causer des dommages auditifs.

3. Contenu du colis

Vérifiez que tous les éléments sont présents dans le colis :

• Thomson WHP3001BK Wireless Headphones (1 unit)
• UHF Transmitter/Charging Base (1 unit)
• Audio Connection Cable (3.5mm jack to RCA)
• Adaptateur secteur
• Rechargeable AAA NiMH Batteries (2 units, pre-installed or separate)
• Manuel de l'utilisateur (ce document)

4. Produit terminéview

Familiarisez-vous avec les composants de votre système de casque sans fil.

Figure 1 : Thomson WHP3001BK Wireless Headphones resting on their charging base. The headphones feature large, padded earcups and an adjustable headband. The base unit includes indicator lights for charge and power status.

Figure 2 : Côté view of the Thomson WHP3001BK Wireless Headphones, highlighting the over-ear design and the power button with LED indicator on the right earcup.

Figure 3 : Rear panel of the charging base, showing the DC IN port, Audio IN (RCA L/R) ports, and a channel selection switch.

Figure 4 : Included audio connection cable, featuring a 3.5mm stereo jack on one end and red/white RCA plugs on the other, for connecting the transmitter to an audio source.

5. Installation

5.1. Charger les écouteurs

1. Connect the power adapter to the DC IN port on the rear of the charging base (Figure 3).
2. Plug the power adapter into a wall outlet. The "SIGNAL/POWER" LED on the base should illuminate.
3. Place the headphones onto the charging base, ensuring the charging contacts align. The "CHARGE" LED on the base should illuminate, indicating that the headphones are charging.
4. Allow approximately 8-10 hours for the initial full charge. Subsequent charges may take less time.

Note: The headphones use 2 AAA NiMH rechargeable batteries. Ensure these are correctly inserted if not pre-installed.

5.2. Connexion de l'émetteur à une source audio

The transmitter connects to your audio source (e.g., TV, stereo system, computer) via a 3.5mm jack.

1. Identify the audio output port on your source device. This is typically a 3.5mm headphone jack or RCA audio output ports (red and white).
2. Using the supplied audio cable (Figure 4), connect the 3.5mm jack end to your source device's headphone output.
3. Connect the red and white RCA plugs to the "AUDIO IN" ports on the rear of the charging base (Figure 3).
4. If your source device only has RCA outputs, use the RCA ends of the cable for both connections. If your source device has a 3.5mm output, use the 3.5mm end for the source and the RCA ends for the base.
5. Ensure the audio source is powered on and playing audio. The "SIGNAL/POWER" LED on the base should turn green when an audio signal is detected.

Important: When connecting to a TV's headphone jack, the TV's internal speakers may be muted. To allow others to hear the TV, consider using an alternative audio output (e.g., RCA audio out, optical out with a converter) if available.

5.3. Initial Pairing and Tuning

1. Ensure the transmitter is powered on and receiving an audio signal (green "SIGNAL/POWER" LED).
2. Turn on the headphones by pressing the power button on the right earcup. The LED on the headphones will illuminate.
3. The headphones feature auto-tuning. They will automatically search for and connect to the strongest signal from the transmitter.
4. If you experience interference, you may need to adjust the channel switch on the rear of the transmitter (Figure 3) and allow the headphones to re-tune.

6. Fonctionnement

6.1. Mise sous/hors tension

• To power on the headphones, press and hold the power button on the right earcup until the LED illuminates.
• To power off the headphones, press and hold the power button until the LED turns off.
• The transmitter powers on automatically when connected to power and an audio signal is detected. It will enter standby if no signal is present for a period.

6.2. Contrôle du volume

• Adjust the volume using the volume control dial located on the headphones.
• For optimal sound quality and to minimize static or hiss, it is recommended to set the volume of your audio source (TV, stereo) to a high level and then adjust the headphone volume to your desired listening level.

6.3. Portée

The Thomson WHP3001BK headphones offer a wireless range of up to 100 meters in open areas and approximately 20-30 meters indoors, depending on environmental factors and obstacles.

7. Entretien

7.1. Nettoyage

• Essuyez les écouteurs et l'émetteur avec un chiffon doux et sec.
• N’utilisez pas de nettoyants liquides ni de matériaux abrasifs.

7.2. Entretien de la batterie

• Use only the specified NiMH rechargeable AAA batteries.
• Si vous n'utilisez pas les écouteurs pendant une période prolongée, retirez les piles pour éviter les fuites.
• Remplacez les piles lorsque leurs performances se dégradent significativement.

8. Dépannage

9. Spécifications

10. Garantie et assistance

For warranty information, please refer to the documentation provided at the time of purchase or contact your retailer. For technical support, please visit the official Thomson website ou contactez leur service client.

Veuillez conserver votre preuve d'achat pour toute réclamation au titre de la garantie.