Introduction
This manual provides essential instructions for the proper setup, operation, and maintenance of your Intermec SR30 Linear Imager RS232 Barcode Scanner. Please read this manual thoroughly before using the device to ensure optimal performance and to prevent damage.
The Intermec SR30 is a high-performance linear imager designed for reliable barcode scanning in various environments, connecting via an RS232 interface.
Consignes de sécurité
- N’exposez pas le scanner à des températures extrêmes, à l’humidité ou à la lumière directe du soleil.
- Évitez de faire tomber le scanner ou de le soumettre à des chocs violents.
- Do not attempt to open or modify the scanner. Refer all servicing to qualified personnel.
- Use only the power supply and cables provided or approved by Intermec.
- Veillez à ce que la fenêtre de lecture soit propre pour garantir une lecture précise des codes-barres.
Contenu du colis
Vérifiez que votre colis contient les éléments suivants :
- Intermec SR30 Linear Imager Barcode Scanner
- Câble d'interface RS232
- Bloc d'alimentation
- Documentation (this manual or similar)
Si des articles sont manquants ou endommagés, veuillez contacter immédiatement votre fournisseur.
Installation
1. Connexion du scanner
- Connectez le câble RS232 : Plug the RS232 connector of the interface cable into the corresponding serial port on your host computer or POS system.
- Se connecter au scanner : Plug the other end of the interface cable into the port at the base of the SR30 scanner. Ensure a secure connection.
- Connectez l'alimentation : Connect the power supply unit to the power port on the interface cable or directly to the scanner base, as applicable for your specific cable configuration. Plug the power supply into a standard electrical outlet.
2. Mise sous tension initiale
Once connected, the scanner should power on automatically. Observe the indicator lights (typically an LED) for initial status. The scanner may emit a short beep to indicate it is ready for operation.
3. Basic Configuration (if required)
The SR30 scanner may require configuration for specific RS232 communication parameters (e.g., baud rate, data bits, parity) to match your host system. Refer to the detailed programming guide (often a separate document with programming barcodes) for advanced configuration. For basic operation, the default settings are often sufficient.
Utilisation du scanneur
1. Scanner les codes-barres
- But: Point the scanning window of the SR30 at the barcode you wish to read. Ensure the entire barcode is within the scanner's field of view.
- Balayage: Press and hold the trigger button (if applicable) or present the barcode to the scanner's window for automatic scanning.
- Confirmation: A successful scan is typically indicated by an audible beep and/or a change in the LED indicator light (e.g., green light). The barcode data will be transmitted to your host system.
2. Comprendre les indicateurs
- LED verte: Indicates a successful barcode read.
- Red/Amber LED: May indicate an error, scanner busy, or awaiting input. Consult the full programming guide for specific error codes or patterns.
- Beep Sounds: Different beep patterns can indicate successful reads, errors, or configuration changes.
Entretien
Nettoyage du scanneur
- Nettoyez régulièrement la fenêtre de numérisation avec un chiffon doux non pelucheux.ampterminer avec de l'eau ou un nettoyant doux et non abrasif.
- Do not use harsh chemicals, solvents, or abrasive materials, as these can damage the scanner's surface.
- Assurez-vous que le scanner est éteint avant de le nettoyer.
Stockage
Lorsqu'il n'est pas utilisé, rangez le scanner dans un endroit propre et sec, à l'abri de la lumière directe du soleil et des températures extrêmes.
Dépannage
| Problème | Cause possible | Solution |
|---|---|---|
| Le scanner ne s'allume pas. | Power cable not connected; power outlet faulty; power supply unit failure. | Check all cable connections. Try a different power outlet. Ensure the power supply is functioning. |
| Le scanner ne lit pas les codes-barres. | Barcode damaged or poorly printed; scanning window dirty; incorrect symbology enabled; scanner not configured for host. | Ensure barcode is clear. Clean scanning window. Verify scanner configuration matches host system requirements. Try scanning a known good barcode. |
| Barcode data not appearing on host. | RS232 cable loose or faulty; incorrect RS232 communication settings (baud rate, parity); host application not ready. | Check RS232 cable connection. Verify RS232 settings on both scanner and host. Ensure host application is active and ready to receive input. |
Caractéristiques
- Modèle: SR30
- Numéro de pièce : 225-727-003 (Kit)
- Type de scanner: Imageur linéaire
- Interface: RS232
- Fabricant: Intermec
- Poids de l'article : 0.01 ounces (approximate, scanner only)
- Département: Code à barres
- ASIN: B003T0WF3S
Garantie et assistance
For warranty information and technical support, please refer to the documentation provided with your purchase or visit the official Intermec webConsultez le site. Conservez votre reçu d'achat comme preuve d'achat pour toute réclamation au titre de la garantie.
Contact your reseller or Intermec customer service for assistance with issues not covered in this manual.
