1. Introduction
This manual provides essential instructions for the installation, maintenance, and proper use of your Wahl Professional 2-Hole Standard Clipper Blade, Model 1006. Designed for professional precision, this replacement blade ensures accurate and sharp performance for various Wahl clippers. Please read this manual thoroughly before use to ensure optimal performance and longevity of your blade.
Image 1: Wahl Professional 2-Hole Standard Clipper Blade, Model 1006.
2. Compatibilité
The Wahl Professional 2-Hole Standard Clipper Blade (Model 1006) is compatible with the following Wahl clipper models:
- Wahl Super Taper
- Wahl Super Taper II
- Wahl Icon
- Wahl Pro Basic
- Wahl Sterling 9
Image 2: Various Wahl clipper models compatible with the 2-Hole Standard Clipper Blade.
3. Contenu du colis
Your Wahl Professional 2-Hole Standard Clipper Blade package includes:
- 1mm-3mm Standard Clipper Blade
- Huile de lame
- Vis de montage
- Instructions d'installation (ce manuel)
4. Installation de la lame
Follow these steps to properly install your new clipper blade:
- Éteindre: Ensure your clipper is turned off and unplugged from the power source before beginning installation.
- Retirer l'ancienne lame : Using a screwdriver, carefully loosen and remove the two screws holding the old blade assembly to the clipper housing. Set aside the old blade and screws.
- Clean Clipper: Clean any hair or debris from the clipper's blade area using a brush.
- Position de la nouvelle lame : Place the new Wahl Professional 2-Hole Standard Clipper Blade onto the clipper, aligning the holes in the blade with the screw holes on the clipper. Ensure the small moving blade is correctly seated on the drive lever.
- Lame sécurisée : Insert the screws and tighten them just enough to hold the blade in place, allowing for slight adjustment.
- Align Blades: Adjust the blade to ensure the top blade (cutter) is perfectly aligned with the bottom blade (comb), with the teeth of the top blade slightly behind the teeth of the bottom blade. This prevents cutting the skin.
- Serrage final : Once aligned, firmly tighten both screws. Do not overtighten.
- Lubrifier: Apply a few drops of Wahl clipper oil to the teeth of the new blade.
Image 3 : Détail view of the 2-Hole Standard Clipper Blade, highlighting its design and dimensions.
5. Entretien
Proper maintenance is crucial for extending the life and performance of your clipper blade.
5.1 Lubrification des lames
Regular oiling reduces friction, prevents rusting, and ensures smooth cutting performance. Wahl's high-carbon blades benefit significantly from consistent lubrication.
- Appliquer de l'huile : With the clipper turned off, apply a drop of Wahl clipper oil to each corner of the top blade and one drop to the foot of the blade.
- Distribute Oil: Turn the clipper on for a few seconds to allow the oil to work its way into the blades.
- Essuyer l'excédent : Essuyez tout excès d'huile avec un chiffon propre.
It is recommended to oil your blades before or after each use, especially if the clipper feels sluggish or pulls hair.
Video 1: Demonstrates how to oil clipper blades to prevent pulling and ensure smooth operation.
5.2 Nettoyage des lames
After each use, brush off any loose hair from the blades. For a deeper clean, especially after prolonged use or if hair buildup is noticeable:
- Brossez les cheveux : Use a small cleaning brush to remove hair from between the blade teeth.
- Désinfecter (facultatif) : For professional use, consider using a clipper disinfectant spray (e.g., Wahl Clini-Clip Spray) to sanitize the blades. Follow the product's instructions.
- Re-oil: Always re-oil the blades after cleaning or disinfecting to prevent rust and maintain lubrication.
Image 4: Essential maintenance products for Wahl clippers, including blade oil and disinfectant spray.
6. Dépannage
| Problème | Cause possible | Solution |
|---|---|---|
| Clipper pulls or snags hair | Les lames sont émoussées, sales ou mal huilées. | Clean and oil the blades. If the problem persists, the blades may need sharpening or replacement. |
| Blades are rusting | Insufficient oiling or exposure to moisture. | Ensure blades are thoroughly dried after cleaning and regularly oiled, especially in humid environments. |
| La lame ne coupe pas efficacement | Improper blade alignment or worn blades. | Check blade alignment as per installation instructions. If blades are old, consider replacing them. |
7. Spécifications
- Nom du produit: 2-Hole Standard Clipper Blade
- Numéro de modèle : 1006
- Marque: Professionnel Wahl
- Longueur de coupe : 1mm-3mm (Standard)
- Matériel: Acier à haute teneur en carbone
- Dimensions: 2 x 0.1 x 3 pouces
- Poids de l'article : 0.8 onces
- Code à barres : 785085010068 043917100609
- Fabricant: Professionnel Wahl
- Origine: Fabriqué aux États-Unis
8. Garantie et assistance
For warranty information, product support, or to purchase additional accessories, please visit the official Wahl Professional webConsultez leur site web ou contactez leur service client. Conservez votre reçu d'achat comme preuve d'achat pour toute réclamation au titre de la garantie.
Professionnel Wahl Website: www.wahlpro.com
