Introduction
Thank you for choosing the K-1028E Universal Air Conditioner Remote Control. This remote is designed for ease of use and broad compatibility, capable of controlling over 1000 different air conditioner brands worldwide. It features a large LCD display, a built-in clock, and on/off timer functions for convenient climate management.
This remote control is compatible with approximately 99% of air conditioner brands, offering a control distance of about 8-10 meters.
Installation
1. Installation de la batterie
- Ouvrez le couvercle du compartiment des piles au dos de la télécommande.
- Insérez deux (2) piles AAA en respectant la polarité (+/-). Piles non fournies.
- Fermez soigneusement le couvercle du compartiment à piles.
2. Programmation de la télécommande
The K-1028E remote can be programmed using either manual code entry or an automatic search function.
Manual Code Entry (Recommended)
- Allumez votre climatiseur manuellement.
- Locate the brand code for your air conditioner in the provided code list (usually included with the remote, or available online).
- Press and hold the 'SET' button on the remote for approximately 3 seconds until the code on the LCD screen starts flashing.
- Use the 'TEMP ▲' or 'TEMP ▼' buttons to input the 3-digit code for your air conditioner brand.
- Once the correct code is displayed, press the 'OK' button to confirm. The code will stop flashing.
- Test the remote by pressing the 'ON/OFF' button. If the air conditioner responds, the setup is complete. If not, try the next code for your brand or proceed to automatic search.
Recherche automatique
- Allumez votre climatiseur manuellement.
- Pointez la télécommande vers le climatiseur.
- Press and hold the 'SET' button for approximately 6 seconds until the code on the LCD screen starts flashing and automatically searching.
- The remote will send out different codes. Pay close attention to your air conditioner.
- As soon as your air conditioner responds (e.g., turns on/off, changes mode), immediately press the 'OK' button to stop the search and save the code.
- Test the remote's functions. If all functions work correctly, the setup is complete. If not, repeat the automatic search process.
Mode d'emploi
Once programmed, the remote control offers various functions for your air conditioner:
- MARCHE/ARRÊT : Appuyez pour allumer ou éteindre le climatiseur.
- TEMP ▲/▼ : Adjust the temperature setting up or down.
- MODE: Cycle through operating modes (e.g., Cool, Heat, Fan, Dry, Auto).
- VENT: Adjust fan speed (e.g., Low, Medium, High, Auto).
- E-chaleur : Activates electric heating function (if supported by AC).
- LUMIÈRE: Turns the display light on/off.
- M.SWING / A.SWING: Controls horizontal (Manual) and vertical (Auto) swing of the air deflector (if supported by AC).
- TIME ON / TIME OFF: Programmez une minuterie pour que le climatiseur s'allume ou s'éteigne automatiquement.
- F.Cool / F.Heat: Activates fast cooling or fast heating modes (if supported by AC).
- HORLOGE: Set the current time on the remote's display.
- SET: Used for programming and accessing settings.
- OK: Confirme les sélections et les paramètres.
Entretien
- Nettoyage: Essuyez la télécommande avec un chiffon doux et sec. N’utilisez pas de nettoyants liquides ni de produits abrasifs.
- Remplacement de la batterie : Replace batteries when the remote's range decreases or the display becomes dim. Always replace both batteries at the same time with new AAA batteries.
- Stockage: Si vous n'utilisez pas la télécommande pendant une période prolongée, retirez les piles pour éviter les fuites et les dommages. Rangez-la dans un endroit frais et sec, à l'abri de la lumière directe du soleil.
- Évitez les chutes : Handle the remote with care to prevent damage from drops or impacts.
Dépannage
| Problème | Cause possible | Solution |
|---|---|---|
| Remote not responding / AC not responding | Dead or incorrectly inserted batteries; Remote not programmed correctly; Obstruction between remote and AC unit. | Check and replace batteries; Re-program the remote using manual or automatic search; Ensure clear line of sight to the AC unit's receiver. |
| Limited control distance | Weak batteries; Obstruction; Interference. | Replace batteries; Remove obstructions; Minimize electronic interference. |
| AC functions not working correctly | Incorrect code programmed; AC unit does not support the specific function. | Try another code for your AC brand; Some advanced functions may not be universally supported by all AC models. |
| Remote does not work with a specific AC brand (e.g., Westpoint, Family, Mitsubishi msz-hr35vf, Mirage, Fujitsu) | Code not found or not compatible with specific model. | While compatible with 99% of brands, some specific models may not be supported. Ensure you have tried all available codes for the brand and the automatic search function. If issues persist, the model may not be compatible. |
Caractéristiques
- Numéro de modèle : K-1028E
- Matériel: ABS (acrylonitrile butadiène styrène)
- Distance de contrôle : Environ 8 à 10 mètres
- Alimentation: 2 piles AAA (non incluses)
- Style: Style moderne
- Origine: Chine continentale, Guangdong
Astuces utilisateur
- Keep Code List Handy: If a code list was provided with your remote, keep it in a safe place. It will be useful if you ever need to re-program the remote.
- Auto-Search as a Last Resort: While manual code entry is often quicker if you know your brand's codes, the automatic search function is a reliable alternative if you cannot find your specific code or brand.
- Ligne de mire: Always ensure there is a clear line of sight between the remote control and your air conditioner's infrared receiver for optimal performance.
Garantie et assistance
This product is designed for reliability and ease of use. For any issues not covered in this manual or for further assistance, please contact the seller or retailer from whom you purchased the product. Please retain your proof of purchase for any warranty claims.
