WS2805 Pixels LED Strip Light RGBCCT User Manual

1. Introduction

The BTF-LIGHTING WS2805 Pixels LED Strip Light is an advanced RGBCCT (Red, Green, Blue, Cold White, Warm White) 5-in-1 addressable LED strip designed for dynamic and versatile lighting applications. Featuring dual signal capabilities, this strip allows for individual control of each LED segment, enabling complex lighting effects and precise color tuning from 3000K to 6500K white light. This manual provides essential information for the safe and effective use of your LED strip.

Figure 1: WS2805 Pixels LED Strip Light

2. Consignes de sécurité

• Assurer le vol de travailtage matches the strip's requirements (DC12V or DC24V). Using an incorrect voltage can damage the strip.
• Always disconnect power before installation, cutting, or maintenance.
• Do not bend the LED strip sharply, as this can damage the circuit board and LEDs.
• For IP67 rated strips, while the strip itself is waterproof, the 4-pin connectors are not. Ensure connectors are protected from moisture if used outdoors.
• IP30 and IP65 rated strips are designed for indoor use only.
• Tenir hors de portée des enfants.

3. Contenu du colis

Votre colis doit contenir les éléments suivants :

• 1 x WS2805 Pixels RGBCCT LED Strip (available in 1m, 3m, or 5m lengths)
• 1 x 4-pin connector
• 1 x Manuel d'utilisation (ce document)

Note: Power supply and pixels LED controller are NOT included and must be purchased separately.

Figure 2: Package Contents (New Edition shown on left)

4. Spécifications

Figure 3: WS2805 LED and IC Chip Details

Figure 4: WS2805 12V Dimensions (IP65/IP30 and IP67)

Figure 5: DC24V 84LED/m Dimensions (IP30, IP65, IP67)

5. Installation

5.1 Prérequis

• A compatible DC12V or DC24V power supply (depending on your LED strip variant).
• A compatible pixels LED controller (e.g., SP630E or similar WS2805 compatible controller).

Important: This light strip is not compatible with WLED/ESP32 controllers.

5.2 étapes d'installation

1. Préparez la surface : For strips with adhesive tape (IP30 and IP65), ensure the installation surface is smooth, clean, and dry.
2. Cut to Length (Optional): If custom lengths are required, cut the LED strip only at the designated cut marks. Do not bend the LED strip sharply.
   • 60 LED/M (DC12V): Can be cut every 3 LEDs (approx. 5cm).
   • 60 LED/M (DC24V): Can be cut every 6 LEDs (approx. 10cm).
   • 84 LED/M (DC24V): Can be cut every 7 LEDs (approx. 8.27cm).
3. Connect the Strip: Use the provided 4-pin connector to connect the LED strip to your pixels LED controller. Ensure the data direction arrow on the strip aligns with the controller's output.
4. Connecter l'alimentation : Connect the power supply to the pixels LED controller. For longer LED strip runs, it is recommended to power the strip from both ends using the 2-pin power wires to reduce voltage drop et assure une luminosité constante.
5. Sécuriser la bande : For IP30 and IP65 strips, peel off the backing from the adhesive tape and firmly press the strip onto the prepared surface. For IP67 strips, use appropriate mounting clips or channels (not included) to secure the strip.

Figure 6 : Schéma de connexion

Figure 7: Series Connection & Voltage Supplémentation

Figure 8: IC Control per LED Segment

6. Mode d'emploi

Once the LED strip is properly installed and connected to a compatible power supply and pixels LED controller, you can begin operating it. Refer to your specific pixels LED controller's manual for detailed instructions on its functions and app control.

6.1 Fonctionnement de base

• Marche/Arrêt : Use the power button or app control on your LED controller to turn the strip on or off.
• Sélection de couleur : Utilize the controller's interface or app to select from 16 million monochrome effects, including various RGB colors and pure white light.
• Effets dynamiques : Explore pre-programmed dynamic effects such as multi-color chasing effects and pure white lighting effects.
• Réglage de la lumière blanche : Adjust the white light temperature from Warm White (3000K) to Cold White (6500K) to suit your ambiance needs.

Figure 9: Multi-color Chasing Effects and Pure White Light

Figure 10: White Light Color Temperature Options

7. Entretien

7.1 Nettoyage

To clean the LED strip, gently wipe it with a soft, dry cloth. Avoid using harsh chemicals or abrasive materials that could damage the LEDs or the strip's coating.

7.2 Directives d'étanchéité

• IP30 (Non-waterproof): Suitable for dry indoor environments only. Avoid any contact with liquids.
• IP65 (Silicone Coating): Dust prevention and water-resistant. Works indoors only. Not suitable for direct water exposure.
• IP67 (Silicone Sheathing): Dust prevention and waterproof design. Can work outdoors, but the 4-pin connectors are non-waterproof and must be protected from moisture.

Figure 11: IP65 Silicone Coating Waterproof (Indoor Only)

Figure 12: IP67 Silicone Sheathing Waterproof (Can Work Outside)

7.3 Solder Joints

It is normal for the LED strip to have solder joints approximately every 0.5 meters. This is a standard manufacturing process and does not indicate a quality problem.

8. Dépannage

• Pas de lumière : Vérifiez si l'alimentation est correctement connectée et fournit le volume correcttage (DC12V or DC24V). Ensure the LED controller is properly connected and powered on.
• Couleurs/Effets incorrects : Verify that the LED controller is compatible with WS2805 strips and that the settings in the controller's app or interface are configured correctly for RGBCCT pixels. Check the data direction of the strip.
• Dimming/Color Shift at End of Strip (Voltage Drop): For longer installations, ensure you are injecting power at both ends of the LED strip to compensate for voltage goutte.
• Individual LED Segment Failure: The WS2805 features 'Break-Point Transmission', meaning if one LED segment fails, the signal will continue to the subsequent segments, preventing the entire strip from failing. However, the failed segment will not light up.
• Incompatibility with WLED/ESP32: This LED strip is explicitly not compatible with WLED/ESP32 controllers. Please use a dedicated WS2805 compatible pixels controller.

Figure 13: Break-Point Transmission and No Voltage Déposez

9. Conseils d'utilisation

• Choosing a Controller: Since the strip requires a pixels controller, ensure the one you purchase is specifically designed for WS2805 addressable LEDs. The product video showcases an SP630E controller as an example of a compatible device.
• Connecteurs : The strip comes with a 4-pin connector. Ensure your chosen controller and any extension cables are compatible with this connector type.
• Addressable Segments: For the 12V version with 60 LEDs/meter, each IC controls 3 LEDs, meaning you can address segments of 3 LEDs. This is useful for planning your lighting effects.

10. Garantie et assistance

BTF-LIGHTING provides a 12-month manufacturer's limited warranty for defective items, excluding damage caused by misuse or improper installation. Accessories included with the product come with a 3-month warranty. If you encounter any issues, please contact the seller within the warranty period. Defective items must be reported and returned within the warranty period in their original packaging. We do not repair or replace items with an expired warranty.