1. Introduction
This manual provides essential information for the installation, operation, and maintenance of your FACULX 36/48V 35A 1500W Ebike Brushless Motor Controller. This controller is designed for electric bicycles, offering efficient power management for brushless motors and compatibility with various LCD displays (LCD3, LCD4, LCD5, LCD7). Please read this manual thoroughly before installation and use to ensure proper function and safety.
2. Consignes de sécurité
- Always disconnect the battery before performing any installation, maintenance, or repair work on the ebike electrical system.
- Ensure all connections are secure and correctly polarized to prevent damage to the controller or other components.
- Avoid exposing the controller to water, excessive moisture, or extreme temperatures.
- N'essayez pas d'ouvrir ou de modifier le contrôleur casing. This may void the warranty and pose a safety risk.
- Consult a qualified technician if you are unsure about any installation steps or encounter persistent issues.
3. Contenu du colis
Vérifiez que tous les éléments sont présents dans votre colis :
- FACULX 36/48V 35A 1500W Ebike Brushless Motor Controller (Model: 36/48KSRL-FF01) with integrated wiring harness.
Image 3.1 : Terminéview of the FACULX Ebike Brushless Motor Controller with its integrated wiring harness.
4. Configuration et installation
Follow these steps to correctly install your ebike controller. Ensure the battery is disconnected before starting.
4.1. Montage du contrôleur
Mount the controller securely to your ebike frame in a location protected from physical impact and moisture. Use appropriate fasteners (not included) to ensure it is stable during operation.
4.2. Connexions de câblage
Identify each connector on the controller's wiring harness and connect them to the corresponding components on your ebike. Refer to the images below for visual guidance.
- Connexion de la batterie : Connect the main power cables (typically red for positive, black for negative) to your ebike battery. Ensure correct polarity. This controller uses a common XT60 or similar high-current connector for the battery.
- Fils de phase du moteur : Connect the three thick phase wires (usually green, blue, yellow) from the controller to the corresponding phase wires of your brushless motor.
- Câbles du capteur à effet Hall : Connect the smaller Hall sensor wire bundle (typically 5 or 6 wires) from the controller to the motor's Hall sensor connector.
- Connexion d'affichage : Connect the display cable to your compatible LCD3, LCD4, LCD5, or LCD7 display unit. This is often a multi-pin waterproof connector.
- Connexion de l'accélérateur : Connect the throttle cable to your ebike's throttle unit.
- Brake Lever Connections: Connect the brake lever cables. This controller supports low-level brake input.
- Pedal Assist Sensor (PAS) Connection: If your ebike has a PAS, connect its cable to the controller.
- Autres connexions : Connect any other auxiliary cables such as lights or speed sensors if applicable and supported by your controller model.
Image 4.1 : Détail view of the controller's wiring harness, showing different connector types for various ebike components.
Image 4.2 : Example of a multi-pin connector, often used for display or throttle connections.
Image 4.3 : Example of ring terminal connectors, typically used for motor phase wires.
5. Mode d'emploi
Once the controller is correctly installed and all connections are secure, you can begin operating your ebike.
- Mise sous tension : Turn on your ebike battery and then power on your LCD display unit. The display should illuminate and show relevant information.
- Commande d'accélérateur : Gently twist the throttle to engage the motor. The motor speed will correspond to the throttle input.
- Assistance au pédalage (PAS) : If equipped, begin pedaling, and the PAS system will provide motor assistance based on your pedaling effort and the selected assist level on your display.
- Freinage: Activating the brake levers will cut off power to the motor, ensuring safe stopping.
- Fonctions d'affichage: Use your LCD display to monitor speed, battery level, assist level, and other parameters. Refer to your specific LCD display manual for detailed instructions on its functions.
6. Entretien
Proper maintenance ensures the longevity and reliable performance of your controller.
- Inspection régulière : Vérifiez périodiquement le serrage de tous les branchements électriques et l'absence de signes d'usure ou de dommages.
- Propreté: Keep the controller clean and free from dust, dirt, and debris. Use a dry cloth for cleaning. Do not use water or harsh chemicals.
- Protection de l'environnement : Store and operate your ebike in conditions that protect the controller from extreme weather, direct sunlight, and high humidity.
- Gestion des câbles: Ensure cables are neatly routed and secured to prevent snagging or damage during riding.
7. Dépannage
Si vous rencontrez des problèmes avec votre manette, consultez les problèmes et solutions courants suivants :
| Problème | Cause possible | Solution |
|---|---|---|
| Le moteur ne fonctionne pas | Loose battery connection, low battery, motor/Hall sensor wires disconnected, faulty throttle/display. | Check battery charge and connections. Verify all motor, Hall sensor, throttle, and display cables are securely connected. |
| L'écran ne s'allume pas | Battery off, display cable loose/damaged, faulty display. | Ensure battery is on. Check display cable connection. Test with a known good display if possible. |
| Le moteur s'arrête par intermittence. | connexions desserrées, surchauffe, tension de batterie faibletage. | Inspect all connections. Allow controller to cool down. Check battery voltage. |
| Incorrect speed reading on display | Speed sensor issue, incorrect display settings. | Check speed sensor connection. Verify wheel size and other parameters are correctly set in the display. |
If the problem persists after attempting these solutions, please consult a professional ebike technician.
8. Spécifications
The following are the technical specifications for the FACULX Ebike Brushless Motor Controller (Model: 36/48KSRL-FF01):
Image 8.1: Controller label displaying key specifications.
- Modèle: 36/48KSRL-FF01
- Vol évaluétage: DC36V/48V
- Courant nominal : 17A
- Courant maximal : 35±1A
- Speed Set: 1-4.2V
- Brake Input: Niveau faible
- Vol faibletaget Protection: DC30/40±0.5V