MOUNTUP Single Monitor Desk Mount (Model B0DNJ321JD) Instruction Manual

Introduction

Thank you for choosing the MOUNTUP Single Monitor Desk Mount. This manual provides detailed instructions for the safe and efficient installation, operation, and maintenance of your monitor arm. This mount is designed to enhance your workspace ergonomics by providing flexible positioning for your monitor.

Figure 1: Extended reach of the MOUNTUP Single Monitor Arm, offering up to 27.7 inches of extension and 17 inches of height from the desk surface.

Caractéristiques

The MOUNTUP Single Monitor Desk Mount is built with high-quality alloy steel to ensure durability and stability. Please review the following specifications to ensure compatibility with your monitor and desk setup.

Figure 2 : Compatibilité surview for monitor size, VESA patterns, and weight capacity.

Instructions d'installation

Carefully follow these steps to install your MOUNTUP Single Monitor Desk Mount.

1. Choisissez votre méthode de montage

Le bras du moniteur prend en charge deux méthodes d'installation : C-Clamp et fixation par œillet. Choisissez la méthode qui convient à votre bureau.

Figure 3: Two available installation methods: C-Clamp for desk thickness 0.39"-3.15" and Grommet Mount for desk thickness 0.39"-1.97" with hole diameter 0.39"-2.36".

Cl-Camp Installation:

1. Attachez le C-clamp base to the edge of your desk. Ensure the desk thickness is between 0.39" and 3.15".
2. Serrez le clamp Visser solidement jusqu'à ce que la base soit stable.

Installation du support à œillets :

1. Insert the grommet base through an existing desk hole. Ensure desk thickness is between 0.39" and 1.97" and hole diameter is between 0.39" and 2.36".
2. Secure the base from underneath the desk using the provided hardware.

2. Assemble the Arm and Attach Monitor

1. Slide the main pole onto the installed base and secure it.
2. Attach the monitor arm to the main pole at your desired initial height.
3. Attach the VESA plate to the back of your monitor using the appropriate screws. This mount supports VESA patterns 75x75mm and 100x100mm.
4. Slide the monitor (with VESA plate attached) onto the arm's mounting head until it clicks into place.

Mode d'emploi

The MOUNTUP Single Monitor Desk Mount offers extensive adjustability for optimal viewconfort.

Réglages du moniteur :

• Réglage de la hauteur : The arm allows for up to 28.5 inches of vertical adjustment. Gently push or pull the monitor to raise or lower it.
• Extension/Rétraction : Extend the arm up to 27.7 inches or retract it closer to the pole to find your ideal viewdistance.
• Inclinaison: Tilt your monitor +90°/-90° to reduce glare and optimize your viewangle de vue.
• Pivot: Swivel the monitor +90°/-90° to share your screen with others or adjust for different tasks.
• Rotation: Rotate your monitor +180°/-180° to switch between landscape and portrait orientations. Note that some force may be required for rotation, which is normal for secure positioning.

Figure 4: Full motion capabilities of the monitor arm for ergonomic positioning.

Figure 5: Visual representation of the monitor's adjustable angles.

Réglage de la tension du ressort à gaz :

The gas spring mechanism allows for smooth and stable height adjustments. You may need to adjust the tension based on your monitor's weight.

1. Ensure the arm is in a horizontal position before adjustment.
2. Locate the tension adjustment screw on the arm (often marked with '+' and '-' symbols).
3. Use the provided Allen key to turn the screw:
• Tourner clockwise ('-') à réduire la tension for lighter monitors (monitor raises up easily).
• Tourner counter-clockwise ('+') à augmenter la tension for heavier monitors (monitor drops down easily).
4. Adjust gradually until the monitor stays at your desired height without drifting up or down.

Figure 6: Gas spring tension adjustment for optimal monitor stability.

Entretien

Regular maintenance ensures the longevity and optimal performance of your MOUNTUP monitor arm.

• Nettoyage: Essuyez le bras et la base avec un chiffon doux et sec.amp tissu. Évitez les nettoyants abrasifs qui pourraient endommager la finition.
• Contrôle d'étanchéité : Vérifiez régulièrement le serrage de toutes les vis et fixations. Resserrer si nécessaire.
• Ressort à gaz : The gas spring is designed for long-term use, tested for over 20,000 lifts. If you notice a change in the arm's ability to hold position, refer to the "Gas Spring Tension Adjustment" section.

Figure 7: The durable gas spring arm is tested for over 20,000 lifts.

Gestion des câbles:

Utilisez le système de gestion des câbles intégré pour garder votre espace de travail bien rangé.

• Route monitor cables through the clips or channels along the arm to prevent clutter.
• Veillez à ce que les câbles aient suffisamment de mou pour permettre une amplitude de mouvement complète sans tension.

Figure 8: Integrated cable management and convenient tool storage help maintain a clean desk.

Dépannage

Si vous rencontrez des problèmes avec le bras de votre écran, veuillez consulter les solutions courantes suivantes :

• Monitor does not stay at desired height or drifts: This indicates incorrect gas spring tension. Adjust the tension screw as described in the "Gas Spring Tension Adjustment" section under Operating Instructions. Increase tension for heavier monitors, decrease for lighter ones.
• Le bras est raide ou difficile à bouger : The joints may be too tight. Loosen the relevant screws at the arm joints slightly. For monitor rotation, applying a bit of force is normal, and a cracking sound might occur, which is part of the design for secure positioning.
• L'écran oscille : Assurez-vous que toutes les vis de fixation (bureau cl) sont bien en place.amp/grommet and VESA plate) are securely tightened. Check that the monitor's weight is within the specified range (4.4-19.8 lbs).
• Pièces manquantes ou composants endommagés : Do not attempt to assemble or use the product. Contact MOUNTUP customer support immediately for assistance.

Informations sur la garantie

The MOUNTUP Single Monitor Desk Mount (Model B0DNJ321JD) comes with a Garantie de 3 ans À compter de la date d'achat, cette garantie couvre les défauts de fabrication et les vices de matériaux dans des conditions normales d'utilisation. Veuillez conserver votre preuve d'achat pour toute réclamation au titre de la garantie.

Assistance clientèle

For further assistance, technical support, or warranty inquiries, please contact MOUNTUP customer service through the retailer's platform or the official MOUNTUP website. Our support team is available to help you with any questions or concerns regarding your product.